• Journal of Advanced Marine Engineering and Technology
• /
• v.27 no.1
• /
• pp.76-81
• /
• 2003

The purpose of this study is to analyze the collapse characteristics of widely used spot welded section members coated damping material Y1000 and to develop an analysis method for acquiring exact collapse loads and energy absorption ratio. Hat-shaped thin-walled members have the biggest energy absorbing capacity in a front-end collision. The sections were tested on quasi-static and impact loads. Specimens with two type thickness, width ratio and spot weld pitch on the flange have been tested in impact velocities(6.73n0sec and 7.54n1sec) which imitate a real-life car collision. As a result, it was developed the system for acquiring impact energy absorbing characteristics of structure united thin-walled member and damping materials.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2007.05a
• /
• pp.1181-1184
• /
• 2007

The differential equations governing free, in-plane vibrations of linearly elastic circular arches with rotationally flexible supports, including the effects of rotatory inertia, shear deformation and axial deformation, are solved numerically using the corresponding boundary conditions. The lowest four natural frequencies and the corresponding mode shapes are obtained over a range of non-dimensional system parameters: the subtended angle, the slenderness ratio, and the rotational spring stiffness.

• Journal of the Korean Society for Advanced Composite Structures
• /
• v.3 no.2
• /
• pp.47-54
• /
• 2012

In this study, composite laminate cantilever type cylindrical shells with edge-stiffeners are analyzed. A versatile 4-node flat shell element which is useful for the analysis of shell structures is used. An improved flat shell element is established by the combined use of the addition of non-conforming displacement modes and the substitute shear strain fields. Two models by load conditions are considered. Load type A and B are loaded by point load at the free edge and line load respectively. A various parameter examples are presented to obtain proper stiffened length and stiffened thickness of edge-stiffeners. It is shown that the thickness of shell can be reduced minimum 30% by appropriate edge-stiffeners.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.53 no.9
• /
• pp.525-531
• /
• 2004

This paper proposes inserted core type of slotless Permanent Magnet Linear Synchronous Motor(PMLSM) to improve its low thrust density. However, by inserting the core between windings of each phase, detent force is generated and it acts as thrust ripple. Furthermore, linear motors generate end effect making thrust ripple. So, this paper applies the neural network to minimize detent force and to maximize thrust. Also, sub-poles is placed at the end parts of the mover to compensate end effect. To confirm of calculation method's validity, the calculated results are compared with experimental results.

• Journal of the Korean Magnetics Society
• /
• v.4 no.2
• /
• pp.106-113
• /
• 1994

This paper deals with the magnetic forces of the combined levitation and guidance EDS(Electrodynamic Suspension) maglev system when the car bogie is tilted by the roll, pitch and yaw. The end effect on the magnetic forces are considered by calculating the air-gap flux without the assumptions for its pattern. Induced voltages and currents of the ground coils are given as results. The restoring torque due to roll, pitch and yaw of the bogie body are also examined. It has been shown that the end effect of the concentrically loaded vehicle are not negligible and the combined EDS is stable maglev system against disturbing forces.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.55 no.9
• /
• pp.459-464
• /
• 2006

The detent force by end-effect has an undesired influence on moving coil type Permanent Magnet Linear Synchronous Motor(PMLSM). So, the reduction of detent force by end-effect is especially required for the improvement of thrust characteristics. In this paper, in order to reduce detent force by end-effect, the auxiliary-teeth is installed at the end part of mover. It is also analyzed by Finite Element Analysis(FEA) and optimized by using neural network. By comparison, the detent force is reduced about 41.4[%] comparing to that of basic model.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.14 no.2
• /
• pp.36-42
• /
• 2000

This paper presents the characteristics analysis of electromagnetic pump using linear induction motors. The electromagnetic pump is designed to transfer the molten metals by the electromagnetic force of linear induction motors. The characteristics f a linear induction motor are analysed by the equivalent circuit method considering the end effects. For the verification of the analysis method, the locked test and load test with molten tin were made. The test results of locked test were compared with the simulations, and the velocity of the load test with molten zinc showed 0.24[m/x] with air gap 30[gap] which is sufficient for transferring molten tin.

• Proceedings of the KSR Conference
• /
• 2009.05a
• /
• pp.978-983
• /
• 2009

This paper analyzed longitudinal end effect occurred in linear induction motor by using I-d direct solution and its result is verified by 2-d Finite Element Method(FEM). Longitudinal end effect of linear induction motor caused by magnetic discontinuity in primary core and electric discontinuity in armature winding has been investigated by many researchers. In this paper, 1-d direct solution and boundary conditions proposed by Yamamura and Nasar is used to analyze end effect of linear induction motor and its solution is verified by 2-d FEM.

• Proceedings of the KIEE Conference
• /
• 1994.07b
• /
• pp.1445-1447
• /
• 1994

This paper deals with the edge effect in thin insulating films, focusing on their dependence on film thickness, so we derived a simple mathematical form which depicts that reducing film thickness lowers the field at the electrode edge. we expect that this result may be suitable to problems with multi level insulating films.

• Proceedings of the KIEE Conference
• /
• 2000.07b
• /
• pp.981-983
• /
• 2000

Linear induction motors have static and dynamic end effects due to its finite core length, so that per-phase impedances are asymmetric and the air gap flux distribution is distorted. Because of these points the d-q equivalent circuit model considering both end effects has not been exactly completed. So this paper proposes a characteristic analysis method considering both static and dynamic end effect of the LIM. This method is to utilize asymmetric d-q equivalent circuit model with dynamic end effect coefficient. As a result, it is shown that the simulation results have a good agreement with experimental ones.