• 한국전산유체공학회:학술대회논문집
• /
• 2009.11a
• /
• pp.211-217
• /
• 2009

The numerical program has been developed for the purpose of the complicate geometries application using CIP method. The non-staggered, non-orthogonal, and unstructured grid system can be also used for the various geometries in the program. For validating CIP solver, the lid-driven cavity flow and solitary wave propagation flow are carried out. Test results show a good agreement with the verified results. The dynamic solver was used for the behavior of moving body. Interface process between the two solvers is introduced. The research was performed on the flow problem around torpedo and log and the flow problem in a tank in order to analyze the three phase flow problem Although the comparison to the verified results was not quantitatively performed, the trend of the results was reasonable.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.19 no.7
• /
• pp.651-658
• /
• 2009

In this study, computer applied engineering(CAE) techniques are fully used to efficiently conduct structural and dynamic analyses of a huge composite rotor blade using super-element. Computational fluid dynamics(CFD) is used to predict aerodynamic loads of the rotating wind-turbine blade. Structural vibration analysis is conducted based on the non-linear finite element method for composite laminates and multi-body dynamic simulation tools. Various numerical results are presented for comparison and the structural dynamic behaviors of the rotor blade are investigated herein.

• Proceedings of the KIEE Conference
• /
• 2004.10a
• /
• pp.73-76
• /
• 2004

자동 부하 전환 개폐기는 일반적으로 주 전원의 전압 상태를 감시하여 주 전원의 정전이나, 저 전압 이 감지 될 때 주 전원을 개방시키고, 예비 전원으로 신속하게 전환 시킬 수 있는 구동 메커니즘이 필요하며, 주 전원이 정상 상태로 복구되면 다시 예비 전원에서 주 전원으로의 신속한 전환이 요구 되어진다. 본 논문에서 연구되는 자동 부하 전환 개폐기의 구동부는 1개의 구동력으로 2개 선로의 스위치를 동시에 조작하게 할 수 있는 링크 구조와 동작 원리를 간지고 있으며, 이 동작을 안정적이고 신뢰도 높게 조작하기 위해서 개폐기 구동부의 동특성을 구현할 수 있는 동적 모델로 검증하여 재작하였다. 보다 정확한 모델 수립을 위하여 기구 동작 시에 발생하는 부품들 사이의 충돌, 마찰, 유연성 등의 많은 동적특성들을 정밀하게 모사 할 수 있는 유연 다물체 동역학을 적용하였으며, 검증하였다.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.17 no.11
• /
• pp.1069-1076
• /
• 2007

The purpose of this study is to improve the performance of a linear feeder that can transport grains uniformly. In order to analyze the dynamic behaviors of a linear feeder, the displacements of the feeder are measured by several accelerometers when it is in an operating condition. After the signal data from the accelerometers are captured in the time domain, the feeder motion in the space is visualized by using graphic computer software. In addition, a dynamic model of the feeder is established for a multi-body dynamics simulation. For the dynamic simulation, RecurDyn, which is a commercial multi-body dynamic package, is used. From the experimental and the computational approaches, an optimal dynamic motion is obtained for uniform transportation of grains. Furthermore, we also consider the determination of design parameters for optimal dynamic motion such as centroid, stiffness, and damping coefficient of the feeder system.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1997.10a
• /
• pp.166-172
• /
• 1997

In order to find out relationship between hit probability and gun firing of a moving tank, a turret and flexible gun system model has been developed using the recursive flexible multibody dynamics. For a firing simulation model, nodal coordinates for a finite element model of a flexible gun have been employed to include traverse loads to the gun tube due to moving bullet and ballistic pressure. Modal coordinates are also used to represent the motion induced gun vibration before a firing occurs. An efficient switching technique from modal equations to nodal equations has been introduced for an entire gun firing simulation with rotating turret.

• Proceedings of the KSR Conference
• /
• 2008.11b
• /
• pp.1607-1613
• /
• 2008

The present investigate is a base investigate required in development of DMT wagon train. And it deduced that follows by developing trail analysis model about Modalohr wagon train and examining traveling movement specific using analysis model developed. Vibration acceleration of all direction was increased with addition of travel speed and first suspension. But in case of right and left vibration acceleration, that could influenced by nonlinear specific of first suspension. Therefore checking about those is needed. Frequency of $2{\sim}3\;Hz$ and $7{\sim}8\;Hz$ generated in Right and left, up, down vibration of vehicle. And right and left vibration of bogie generated $25{\sim}35\;Hz$ in low speed section and frequency of $40{\sim}50\;Hz$ in high speed section, $25{\sim}35\;Hz$ in low speed section, $10{\sim}15$ or $40{\sim}50\;Hz$ in high speed section.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.39 no.3
• /
• pp.303-309
• /
• 2015

In this study, a vehicle dynamic analysis and roller rig test were performed to evaluate the applicability of a suspensionless composite bogie to railway vehicles. A vehicle dynamic analysis was carried out under different rubber bushing stiffness values. The stiffness of the rubber bushing that plays a role in guiding wheel sets was varied in the range of 10-100 MN/m, in 10-MN/m steps. Based on the results, the composite bogie with a rubber bushing stiffness of more than 40 MN/m satisfied the design requirements. In addition, a rubber bushing with a stiffness of 81 MN/m was fabricated, and a roller rig test was performed. Based on the test results, the vehicle equipped with the composite bogie had a critical speed of 363 km/h, which agreed with the simulation result within an error of 10%.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.38 no.11
• /
• pp.1231-1237
• /
• 2014

It is essential to perform driving performance tests of military vehicles on rough terrain. A full car test is limited by cost and time constraints, because of which a dynamic analysis via computer simulation is preferred. In this study, a vehicle model is developed using MSC.ADAMS, a commercial multibody analysis program, and compared via experiments. FTire is modeled using the results of a tire performance test to obtain the vertical stiffness. A nonlinear damper is modeled by a characteristic experiment. Leaf springs are modeled with beam force elements and consisted to a vehicle model. The vertical force and acceleration response of the wheel are identified when vehicle is passing over a simple bump as well as a sinusoidal road. The developed vehicle model is verified with the results of a full car test.

• Journal of the Korean Society for Aviation and Aeronautics
• /
• v.19 no.1
• /
• pp.1-6
• /
• 2011

The free-wing tilt-body aircraft is researched in the flight performance characteristics such as short take-off and landing capability, and reduced sensitivity to gust and center of gravity (CG) change. Due to the main wing separating from the fuselage, the high tiltable empennage, and the stub-wing strongly influencing from the propeller wake, the resulting vehicle aerodynamics and flight dynamics are quite different from those of a conventional fixed-wing aircraft. Using the governing flight dynamics model was studied previously, all of speed and body tilt angle is simulated to determine the flight envelope by a non-linear 3-DOF flight simulation analysis. Though flight performance and trimmability are studied, the flight model of free-wing tilt-body aircraft is to reduce the hidden risk and to achieve the successful flight test. It is analyzed the flight characteristics that distinguishes free-wing tilt-body aircraft from the conventional aircraft.

• Proceedings of the KSME Conference
• /
• 2001.06b
• /
• pp.422-427
• /
• 2001

The component mode synthesis method allows the elastic deformation of each component in the flexible multibody system by a sum of modes and modal coordinates. This paper focuses on the selection of boundary conditions and deformation modes for redundantly constrained flexible components in mechanical system dynamics. The result of a flexible body dynamic analysis with only normal modes is used to identify proper boundary conditions of a static modes and a desired set of static modes which will be used in the final model. A simple four bar mechanism is used to explain the procedure and a space satellite with solar panels is analyzed using the proposed method.