• Journal of Ocean Engineering and Technology
• /
• v.29 no.2
• /
• pp.120-127
• /
• 2015

When a deep-seabed lifting pump is kept this device has bending and deformation in the axis due to its long length(8m). These influences can be caused a breakdown. Therefore, a mounting must be developed to keep the lifting pump safe. This paper discusses the hydraulic cylinder design of the lifting pump and structural safety estimation of the mounting using SBD(simulation-based design). The multi-body dynamic simulation method is used, which has been used in the automotive, structural, ship building, and robotics industries. In this study, the position and diameter of the hydraulic cylinder were determined based on the results of the strokes and buckling loads for the design positions of the hydraulic cylinder. A structural dynamic model of the mounting system was constructed using the determined design values, and the structural safety was evaluated using this dynamic model. According to these results, this system has a sufficient safety factor to manufacture.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.9
• /
• pp.84-90
• /
• 2018

In constructing the multi-body dynamics model to analyze the behavior of the railway vehicle, it is very important to understand the properties of the suspension elements that constitute the suspension system. Among them, coil springs, which are mainly used in primary and secondary suspension systems, clearly show the axial stiffness in the drawings, but the lateral properties of the coil springs are not specified clearly, making it difficult to construct a dynamic analysis model. Therefore, in this paper, the model for analyzing the lateral stiffness of the coil spring is examined. A finite element method was applied to analyze the lateral stiffness of the coil spring and numerical analysis was performed by applying the coil spring lateral stiffness analysis model proposed by Krettek and Sobczak. And the test to analyze the lateral stiffness of coil spring was conducted. As a result of comparing with the test results, it was found that the results obtained by applying the lateral stiffness analysis model of Krettek and Sobczak and correcting the correction coefficient are similar to those of the test results.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.40 no.6
• /
• pp.557-563
• /
• 2016

The energy absorption efficiency of a wave power generation system is calculated as the ratio of the wave power to the power of the system. Because absorption efficiency depends on the dynamic behavior of the wave power generation system, a dynamic analysis of the wave power generation system is required to estimate the energy absorption efficiency of the system. In this study, a dynamic analysis of the wave power generation system under wave loads is performed to estimate the energy absorption efficiency. RecurDyn is employed to carry out the dynamic analysis of the system, and the Morison equation is used for the wave load model. According to the results, the lower the wave height and the shorter the period, the higher is the absorption efficiency of the system.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.14 no.4
• /
• pp.199-206
• /
• 2006

Real time vehicle dynamics models have been developed with the subsystem synthesis method for intelligent vehicle HILS system. Three different models for solving subsystem equations are compared in order to find out the best suitable model for HILS applications. The first model is based on the generalized coordinate partitioning technique, and the second one is on the approximate function approach, and the last one is on the constraint stabilization method. To investigate the theoretical efficiency of three proposed methods, arithmetic operators used in the formulations of three models are counted. Bump run simulations with half-sine bump have also carried out with three different models to measure the actual CPU time to validate theoretical investigation.

• Proceedings of the KSME Conference
• /
• 2007.05a
• /
• pp.1009-1014
• /
• 2007

To improve passenger safety, seatbelt systems with pre-tensioner that tightens seatbelt webbing using explosives just before collision are widely adopted. Even though seatbelt must not be unlatched without passenger's operation, release of a buckle due to explosion of pre-tensioner takes place in some situations resulting in serious injury to passengers. To prevent the unintended unlocking, a pendulum like part called anti-g mass is attached to the buckle to block displacement of release button. In this study, the unlocking conditions of anti-g buckle when pre-tensioner explodes has been theoretically investigated. Through multibody model of the seatbelt system incorporating every detailed part of the buckle, dynamic analysis of the seatbelt system with pre-tensioner has been performed including the driver's body model that interacts with seatbelt system. The simulations results has been validated through actual sled test with driver dummy and the seatbelt system.

• Proceedings of the KSME Conference
• /
• 2003.04a
• /
• pp.874-880
• /
• 2003

Many mechanical systems are over-constrained if only rigid bodies are used to model the system. One example of such system is a satellite system with solar panels. To avoid this over-constrained problem, solar panels can be modeled as flexible bodies. The CMS(Component Mode Synthesis) method is widely used to analyze the flexible multi-body system because it can considerably approximate the deformation of the flexible bodies using small number of well-selected mode. However, it is very difficult to decide the boundary condition and the selection of modes. In this paper, the methods for mode synthesis and setting the boundary condition are presented to analyze the flexible multi-body system with over-constraints. Finally, the reliability of proposed method is verified by solar panel's deployment test.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2003.05a
• /
• pp.336-341
• /
• 2003

In this paper, resonance durability analysis technique is presented for the fatigue life assessment considering dynamic effect of a vehicle system. In the resonance durability analysis, the frequency response and the dynamic load on frequency domain are used. Multi-body dynamic analysis, finite element analysis, and fatigue life prediction method are applied for the virtual durability assessment. To obtain the frequency response and the dynamic load, the computer simulations running over typical pothole and Belgian road are carried out by utilizing vehicle dynamic model. The durability estimations on the rear suspension system of the passenger car are performed by using the presented technique and compared with the quasi-static durability analysis. The study shows that the fatigue life considering resonant frequency of vehicle system can be effectively estimated in early design stage.

• Proceedings of the KSME Conference
• /
• 2004.04a
• /
• pp.899-904
• /
• 2004

Multibody dynamics formulation has been developed based on relative cartesian coordinates for subsystem analysis. Relative cartesian coordinates are defined with respect to a reference body of a subsystem. Relative cartesian formulation inherits the same merits of absolute cartesian formulation, such as generality and easy implementation. Two methods have been applied. One is Largrange Multiplier Elimination method and the other is independent coordinate method. A 1/4 car simulation has been carried out to verify the formulations. Since both methods provide identical results, it proves the validity of the formulation.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2005.11a
• /
• pp.564-568
• /
• 2005

As functional requirements of automatic office machines like printers, ATMs, copying machines are on a trend for the higher speed and precision, extensive technical advances are being developed and implemented in the industry. Media transport system is a device to convey a sheet of paper in ATMs and printers. The stability of media transport system is a matter of concern as their operating throughput rapidly increases. And defects of belts or rollers in a transport system directly affect the level of stability of the system. Therefore an automatic diagnostic system for predicting various defects is necessary for the stable operation of the media transport system. A simulation based on multi-body dynamics has been done for a feasibility study of a system design for the defect anticipation.

• Journal of the Korean Society for Precision Engineering
• /
• v.20 no.8
• /
• pp.115-125
• /
• 2003

To analyze the applications of all types of mechanical systems, general purpose analysis programs have been developed and commercialized. However, it is customary to develop and use customized programs even though they sometimes require more work than a general purpose program. A customized program is simplified to adapt to a particular application from the beginning, is designed for small computers, and developed with hardware-in-the-loop in mind so it can be applied effectively. By adding design knowledge and bundling know-how to an analysis program, analysis time can be reduced. And because an analysis has to work in conjunction with other analysis programs, a proprietary program that the user can easily modify can be useful. In this thesis, a multi-body dynamics analysis system is presented using one of the most useful programming techniques, object-oriented concept. The object-oriented concept defines a problem from the physical world as an abstract object, an abstract model. The object becomes encapsulated with the data and method. Simulation is performed using the object's interface. It is then possible for the user and the developer to modify and upgrade the program without having particular knowledge of the analysis program. The method presented in this thesis has the following advantages. Since the mechanical components of the multi-body system converts independent modeling into a class, the modification, exchange, distribution, and reuse of elements are increased. It becomes easier to employ a new analysis method and interface with other S/W and H/W systems. To employ a new analysis method, there is no need to modify elements of the main solver and the Library. In addition, information can be communicated to each object through messaging. It makes the modeling of new elements easier using inheritance. When developing a S/W for the computer simulation of physical system, it is reasonable to use object-oriented modeling. Also, for multi-body dynamics analysis, it is possible to develop a solver that is user-oriented.