• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.17 no.9 s.112
• /
• pp.811-820
• /
• 2006

Ultra wideband CPW batons are proposed in this paper. The proposed talons are consisted of ultra wideband multi-stage Wilkinson dividers and 'X'-shaped $180^{\circ}$ out-of-phase generator. Bottom-bridges and via-holes are used to connect CPW ground lines instead of the conventional air-bridges which require troublesome manual working in fabrication with HMIC(Hybrid Microwave Integrated Circuits) substrates. The proposed CPW batons have ultra wideband of 3 or $10(=F_{figh}/F_{low})$ theoretically, the wideband characteristics and S-parameters of the basis Wilkinson divider are directly converted to those of the proposed batons. The proposed batons are so compact and small compared to the conventional Wilkinson batons because no additional area for out-of-phase section is required. So the size of the proposed batons is exactly the same as that of the basis Wilkinson dividers. As examples, 3-stage and 7-stage wideband Wilkinson dividers are converted to the proposed batons. Their measured operating bandwidth are $1\sim3GHz$ and $0.8\sim5GHz$, respectively, with excellent matching, isolation and power division performances. The measured magnitude and phase balance errors are ${\pm}0.5dB\;and\;0.45\;dB,\;and\;{\pm}5^{\circ}\;and\;{\pm}10^{\circ}C$ over $1\sim3GHz\;and\;0.8\sim5GHz$, respectively.

• Journal of IKEEE
• /
• v.2 no.2 s.3
• /
• pp.278-284
• /
• 1998

This paper describes a l0b CMOS A/D converter (ADC) for HDTV applications. The proposed ADC adopts a typical multi-step pipelined architecture. The proposed circuit design techniques are as fo1lows: A selective channel-length adjustment technique for a bias circuit minimizes the mismatch of the bias current due to the short channel effect by supply voltage variations. A power reduction technique for a high-speed two-stage operational amplifier decreases the power consumption of amplifiers with wide bandwidths by turning on and off bias currents in the suggested sequence. A typical capacitor scaling technique optimizes the chip area and power dissipation of the ADC. The proposed ADC is designed and fabricated in s 0.8 um double-poly double-metal n-well CMOS technology. The measured differential and integral nonlinearities of the prototype ADC show less than ${\pm}0.6LSB\;and\;{\pm}2.0LSB$, respectively. The typical ADC power consumption is 119 mW at 3 V with a 40 MHz sampling rate, and 320 mW at 5 V with a 50 MHz sampling rate.

• Journal of the Korean Geosynthetics Society
• /
• v.7 no.3
• /
• pp.1-7
• /
• 2008

The geotextile tube shall be sewen with geotextile longitudinally in the shape of hose and it shall be filled hydraulically through filling ports at the proper intervals to construct structure. Geotextile container shall be sewen after spreading of geotextile on the split barge and sealed shut after the filling soil, and then moved and positioned at the required position. And the geotextile container passes through the bottom of barge by opening split barge and drops to the seabed to form structure. This structure for the ${\bigcirc}{\bigcirc}$ project, UAE and we would propose that geotextile containment for core material of power plant breakwater to be constructed for lower bunds with containers up to -4.0m and do upper parts with the structures of tube up to 0.0m. For the application of proposed geotextile containment, review on stability of breakwaters and design consideration were adopted. The evaluation on stability of geotextile containment was classified by 3 items, internal design consideration for material selection, reviews on stability for individual and global structure. In this research, the geothermal analysis was performed to estimate the geothermal behavior of central breakwater. Central breakwater is located boundary of intake and outfall channel, it is mean that the central breakwater is thermal boundary of intake low temperature sea water and outfall high temperature sea water. Therefore, it is required to be designed a low permeability to ensure no mix of intake and outfall waters.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.13 no.11
• /
• pp.4950-4955
• /
• 2012

A bolt manufacturing process is completed with continuous forging. Technical and economical success of each process will depend on the appropriate process design and metal mold design for each procedure. This study aims to analyze the moldings of first and second steps among the multi-step molding processes of SCM435 bolt by use of the finite element method in order to achieve the reasonable process. Since the processes of first and second steps analyzed by use of the finite element method consist of axial symmetry, the transformed configuration of material satisfy the dimensions expected in process. In addition, the uniflow line formed in material becomes smooth and consistent over the entire process. Therefore neither molding of material nor inherent defect is expected.

• Tunnel and Underground Space
• /
• v.12 no.4
• /
• pp.259-267
• /
• 2002

Recently, Umbrella Arch Method(UAM) is commonly used in order to enhance the stability of tunnel itself and stabilize the adjacent surface structure. But quantitative estimation of reinforcement effect is needed because UAM is designed and constructed only on the basis of empirical experience. By using 3-dimensional finite element method, parametric study is performed for elastic modulus of ground and overburden, and reinforcement effect is analyzed quantitatively. From the results, surface settlement decreases about 9%∼27% in soil tunnel, about 4%∼24% in weathered rock tunnel and 4%∼17% in soft rock tunnel when applied with UAM. The prediction equation for final surface settlement is suggested through regression analysis and the equation is expressed as exponential function which has variable Smax, unknown coefficient i and k.

• Journal of the Korean Institute of Telematics and Electronics C
• /
• v.36C no.5
• /
• pp.57-66
• /
• 1999

This paper describes a 12b, 50 Msample/s CMOS AID converter using an acquisition-time minimization technique for the high-speed sampling rate of 50 MHz level. The proposed ADC is implemented in a $0.35\mu\textrm{m}$ double-poly five-metal n-well CMOS technology and adopts a typical multi-step pipelined architecture to optimize sampling rate, resolution, and chip area. The speed limitation of conventional pipelined ADCs comes from the finite bandwidth and resulting speed of residue amplifiers. The proposed acquisition-time minimization technique reduces the acquisition time of residue amplifiers and makes the waveform of amplifier outputs smooth by controlling the operating current of residue amplifiers. The simulated power consumption of the proposed ADC is 197 mW at 3 V with a 50 MHz sampling rate. The chip size including pads is $3.2mm\times3.6mm$.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.14 no.10
• /
• pp.1052-1059
• /
• 2003

In this paper, we proposed the directional coupler using two layer microstrip substrate which is improved coupling and isolation. Also, we notified a design method. Modified re-entrant mode coupler is the structure added to the aperture on the ground plane in order to improving the coupling value. And, by adding to slits on the floating conductor, this structure has good performance in isolation, VSWR according to S$\sub$11/, and phase difference. As a result, proposed re-entrant mode microstrip directional coupler has about 1.5 dB more higher coupling and 20 dB more higher isolation than conventional coupler. And because this coupler has good performance in phase difference, it can be used multi-section coupler.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.46 no.12
• /
• pp.59-64
• /
• 2009

In this paper, the design of a new bandstop filter with an ultra-wide stopband is proposed using the metamaterial CRLH-TL. Instead of conventional periodic structures and multi-staged CRLH-TLs, extremely small one-cell type is adopted to circumvent the setbacks of conventional filters such as the lengthened ${\lambda}_g/2$-resonator ones or alternating impedance lowpass filter, and relatively slow skirt. Besides, for a very broad stopband, a strong coupling structure including stepped impedances is suggested and the zero-order resonance is made for effective size-reduction. The validity of the proposed design is proven through the fabrication and measurement, showing the overall size less than ${\lambda}_g/10$, the stopband wider than 12 GHz, 0.7 dB of the insertion loss.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.26 no.11
• /
• pp.966-977
• /
• 2015

This paper presents a novel modified coaxial cavity resonator and its application to bandpass filters with compact size and improved quality factor(Q-factor). The proposed resonator is made up of ${\Gamma}-shape$ or curved four inner conductive posts within a single cavity, which provides quadruplet to realize bandpass filter. No metallic walls inside the cavity are required, and thus the utilization efficiency of the cavity space is improved. As a result, the unloaded Q can be approximately 15 % higher in comparison to the conventional coaxial resonator, or more than 35 % volume saving can be achieved while maintaining the similar Q-factor value with the conventional designs. In addition, due to the multiple cross-coupling occurring within the cavity, including the source-to-load coupling, four flexible transmission zeros can be created to realize different filtering functions. Simulations as well as experimental results of four- and eight-pole filters are presented to validate this attractive design concept. Good agreement between measured and computed results is obtained.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.23 no.1
• /
• pp.122-130
• /
• 2012

In this paper, we propose a broadband vehicle antenna that can operate at the WiBro band(2.3~2.4 GHz) for a wireless internet service. The feeding of the proposed antenna consists of two T-matching networks on both side of the polyarcylate substrate, and the two T-matching networks are connected through via holes. The designed antenna was built and installed on a rear window of a commercial sedan, and the antenna performances, such as the reflection coefficients and the radiation gain are measured in the open-sight area. The received signal strength of the designed antenna was also tested in a strong field area as well as in a weak field area. The measurement results show the matching bandwidth($S_{11}$ <10 dB) of about 300 MHz in the WiBro band and the average gain of about -5.13 dBi along the azimuth direction.