• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2005.11a
• /
• pp.384-394
• /
• 2005

Important characteristics of impinging sprays intersected by a strongly convective gaseous cross flows were experimentally investigated. The breakup processes due to different Weber and Reynolds numbers of liquid and gas streams were visually examined with quantitative measurements of breakup lengths, penetration heights, and droplet sizes. Snapshot images and spay data evidenced that, at lower jet Reynolds number the breakup processes portrays the atomization profiles similar to typical column breakup of single orifice jet. At higher jet Reynolds numbers, disintegration of jet stream is significantly expedited by strong momentum transported from strongly convective gaseous stream. The breakup length and penetration height decreased as the convective flow increase. From the bottom the wall up, the SMD measured the centerline increase. The maximum SMD appeared the top of the SMD distribution

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2005.11a
• /
• pp.395-406
• /
• 2005

Important characteristics of swirl sprays intersected by a strongly convective gaseous cross flows were experimentally investigated. The breakup processes due to different Weber and Reynolds numbers of liquid and gas streams were visually examined with quantitative measurements of breakup lengths, penetration heights, and droplet sizes. Snapshot images and spray data evidenced that, at lower jet Reynolds number the breakup processes portrays the atomization profiles similar to typical column breakup of single orifice jet. At higher jet Reynolds numbers, disintegration of jet stream is significantly expedited by strong momentum transported from strongly convective gaseous stream. The breakup length and penetration height decreased as the convective flow increase. From the bottom the wall up, the SMD measured the centerline first increases and then decreases before again increasing.

• 유체기계공업학회:학술대회논문집
• /
• 2004.12a
• /
• pp.329-336
• /
• 2004

The lock-up position of the floating ring seal affects the leakage flowrate and the stability. And it is changed depending on the operating and geometry condition. In this paper, the leakage flowrate and stability with change of the height and length were investigated by theoretical analysis and experiment. The parameter of the height and length is expressed to the b and L. The decreasing of the b resulted in the increasing of equivalent whirl frequency ratio in the experimental result at the low speed and high pressure not such as theoretical analysis. As the L increased the leakage flowrate decreased and stiffness and direct damping coefficient increased in the experimental result. That was similar to the theoretical analysis.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.14 no.4
• /
• pp.927-936
• /
• 1990

본 연구에서는 정4각 단면덕트의 입구영역에서 층류 정상유동의 유동특성을 이론적 및 실험적인 방법으로 속도파형과 속도분포를 얻어서 유동이 발달되고 있는 유 동특성과 입구길이를 규정하였다. 이론적인 방법으로는 덕트입구영역에서 공기유동 에 대한 운동량방정식을 유도한 후, 운동량방정식 중의 비선형인 대류항을 선형화시켜 서 Laplace변환으로 속도 분포식의 해를 구하였고, 실험적인 방법으로는 시험덕트의 크기가 40*40*4,000nm(가로*세로*높이)인 정 4각단면덕트에 송풍기로 공기를 흡입 하여 정상유동을 얻었고, 열선유속계에 의하여 속도파형과 속도분포 등의 측정한 결과 를 이론식과 비교검토하였다.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.12 no.4
• /
• pp.661-669
• /
• 1999

이 논문은 탄성지반위에 놓인 원호형 곡선보의 자유진동에 관한 연구이다. 회전관성 및 전단변형을 고려하여 두 개의 매개변수로 표현되는 탄성지반위에 놓인 원호형 곡선보의 자유진동을 지배하는 미분방정식을 유도하고, 이를 수치적분기법과 시행착오적 행렬값탐사법이 결합된 수치해석기법으로 해석하였다. 회전-회전, 회전-고정 및 고정-고정의 단부조건을 갖는 곡선보의 최저차모드 3개의 고유진동수를 산출하였다. 곡선보의 수평높이 지간길이비, Winkler 지반계수, 전단지반계수에 따른 고유진동수 변화를 분석하였으며, 회전관성 및 전단변형의 영향을 고찰하였다.

• Journal of Korean Society of Steel Construction
• /
• v.20 no.1
• /
• pp.9-20
• /
• 2008

It is important to increase the economy and efficiency of the diaphragm of the steel box girder bridge design. In this study, an experimental test is performed in a 4-span steel box girder bridge, which was under constructed according to the dead load of slab concrete and vehicle load. The test result is analyzed to verify the stress distribution of the diaphragm and the middle span. Next, stresses on the vertical stiffener are analyzed according to height. Stresses on the diaphragm with equal height are arranged respectively. Also, the stress distribution of the diaphragm and the middle span. Next, stress on the vertical stiffeners are analyzed according to height. Stresses on the diaphragm with equal height are arranged respectively. Also, the vertical stiffeners in the diaphragm was studied, and using the analyzed results, the proper length of the ratio of vehicle load with curing concrete to vehicle load with asphalt is calculated in each part of the steel box girder bridge. The results provide data that serve as basis for an economical and efficient design for the steel box girder bridge diaphragm.

• Korean Journal of Heritage: History & Science
• /
• v.56 no.1
• /
• pp.132-140
• /
• 2023

In this study, a total of 21 parts of the head, carapace, and plastron of 21 tortoises were examined to investigate the characteristics of male and female sexual dimorphism of the Reeve's turtle (Mauremys reevesii), a natural monument in Korea. The ratio values of a total of 19 areas were derived from Head Length (HL) and Carapace Length (CL). As a result of comparing the ratio values, it was found that male tortoises had larger head length, head width, and head height than females compared to the size of the carapace. Since females grow eggs inside the body through internal fertilization after mating, female carapaces are judged to be larger than males overall. As a result of statistical analysis of the ratio values of the measured values, Plastron Length (PL), Bridge Length (BL), Gular Length (GL), Interhumeral Length (IH), Interanal Length (IAN), Femoral-Anal seam (FA) and Head Height (HH) showed statistically significant differences. Statistically significant in the part of the plastron, it is judged that the tortoise acts directly on each deck of the plastron as it grows. In addition, the head size of male tortoises was smaller than that of females, but it was found to be larger in proportion. It is considered that the tortoise has a rather large head compared to the body due to the male's habit of shaking his head and courtship behavior before mating. This study, we were able to identify the characteristics of sexual dimorphism in Reeve's turtle. However, since most of them were rescued, it was not possible to accurately determine habitat and age. In the future, if additional studies are conducted on individuals with clear habitats and ages, it is expected that the characteristics of the physical differences that develop as they grow can be identified.

• The Journal of Korean Academy of Prosthodontics
• /
• v.54 no.2
• /
• pp.110-119
• /
• 2016

Purpose: This study is aimed to assess changes of stress distribution dependent on different connection lengths and placement of the fixture top relative to the ridge crest. Materials and methods: The internal-conical connection implant which has a hexagonal anti-rotation index was used for FEM analysis on stress distribution in accordance with connection length of fixture-abutment. Different connection lengths of 2.5 mm, 3.5 mm, and 4.5 mm were designed respectively with the top of the fixture flush with residual ridge crest level, or 2 mm above. Therefore, a total of 6 models were made for the FEM analysis. The load was 170 N and 30-degree tilted. Results: In all cases, the maximum von Mises stress was located adjacent to the top portion of the fixture and ridge crest in the bone. The longer the connection length was, the lower the maximum von Mises stress was in the fixture, abutment, screw and bone. The reduction rate of the maximum von Mises stress depending on increased connection length was greater in the case of the fixture top at 2 mm above the ridge crest versus flush with the ridge crest. Conclusion: It was found that the longer the connection length, the lower the maximum von Mises stress appears. Furthermore, it will help prevent mechanical or biological complications of implants.

• Maxillofacial Plastic and Reconstructive Surgery
• /
• v.29 no.2
• /
• pp.167-173
• /
• 2007

The temporalis fascia graft has been widely used in the correction of nasal deformities. The fascia can be used alone or combined for augmentation rhinoplasty. The fascia graft provides adequate coverage, contour, and bulk on the profile of the nose, as well as an inconspicuous donor site. A depressed radix area can be successfully corrected by the fascia graft. We present two cases of nasal radix augmentation by using temporalis fascia graft. Two male patients presented with the skeletal class III malocclusion and the depressed radix. A planned orthognathic surgery and the temporalis fascia graft to the radix were performed. The malocclusion and the profile of the patients were markedly improved after the operation. Not only the radix but also the nose was improved in its size and length. There was no noticeable resorption or displacement of the radix area at follow-up. The temporalis fascia graft could be an appropriate surgical technique in radix augmentation and nose lengthening.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.21 no.2
• /
• pp.1-8
• /
• 2017

In order to analyze combustion characteristics of methane-oxygen diffusion flame in a model combustor, combustion experiments were carried out under various spray conditions of propellant scrutinizing combustion stability limit and flame shapes. As the propellant approached the theoretical equivalence ratio condition, a stable detached flame was observed even under high oxygen Reynolds number. And the length of the visible flame increased and the lift-off distance of the flame exhibited a tendency toward decrease. Due to the swirl effect of the propellant by the swirl-coaxial injector, a wide and short flame was produced. Thus, it may be appropriate to employ the swirl-coaxial injector in thrusters having a limited physical dimension.