An Experimental Study on the Stress Distribution in Steel Box Girder Bridge

강박스거더교의 응력분배 거동에 관한 실측연구

  • Received : 2007.10.12
  • Accepted : 2008.02.10
  • Published : 2008.02.20

Abstract

It is important to increase the economy and efficiency of the diaphragm of the steel box girder bridge design. In this study, an experimental test is performed in a 4-span steel box girder bridge, which was under constructed according to the dead load of slab concrete and vehicle load. The test result is analyzed to verify the stress distribution of the diaphragm and the middle span. Next, stresses on the vertical stiffener are analyzed according to height. Stresses on the diaphragm with equal height are arranged respectively. Also, the stress distribution of the diaphragm and the middle span. Next, stress on the vertical stiffeners are analyzed according to height. Stresses on the diaphragm with equal height are arranged respectively. Also, the vertical stiffeners in the diaphragm was studied, and using the analyzed results, the proper length of the ratio of vehicle load with curing concrete to vehicle load with asphalt is calculated in each part of the steel box girder bridge. The results provide data that serve as basis for an economical and efficient design for the steel box girder bridge diaphragm.

강박스거더교 다이아프램부에 있어서 경제적이고 합리적인 설계가 요망되어 진다. 본 연구에서는 시공중인 4경간 강박스거더교에서 콘크리트 상판 타설 시와 차량재하 시에 응력을 측정한다. 측정 결과는 지점부 다이아프램부와 중앙부에서 응력분배를 연구하기 위하여 분석된다. 다이아프램부 수직보강재의 높이별 응력과 이와 같은 높이의 다이아프램부 응력을 정리하고, 이들 결과를 분석하여 적정 수직보강재 길이의 효율성을 판단한다. 또한 다이아프램부 3조의 수직보강재 각각의 응력을 분석하고, 콘크리트 경화 후 차량 재하 시와 시에 따른 응력비를 산출하여 다이아프램부 설계합리화 연구의 기본 자료로 수립하고자 한다.

Keywords

References

  1. 건설교통부 (1996) 강구조물 상세설계기준(도로교)
  2. 한국도로교통협회 (2005) 도로교 설계기준
  3. 김종렬, 김우준, 정경섭 (2003) 강상자형 다이아프램의 수직보 강재 길이에 따른 거동, 한국강구조학회 논문집, 제15권, No. 5, pp. 489-498
  4. 이성행, 김경남, 정경섭 (2005) 강박스거더 지점부 다이아프램 맨홀의 보강방법에 따른 거동, 한국강구조학회 논문집, 제 17권, No. 6, pp. 649-660
  5. 김경남, 김우준, 정경섭 (2002) 강상자형교의 사하중 증가에 따 른 지점부 응력분배 거동, 한국강구조학회 학술발표대회 논문집
  6. Sakai F., and M. Nagai (1977) A Recommendation on the Design of Intermediate Diaphragms in Steel Box, Proceedings of Japanese Society of Civil Engineers, No. 261, May, pp. 21-34
  7. Nakai, H. and Yoo, C. H (1988) Analysis and Design of Curved Steel Bridges, McGraw-Hill, New York
  8. Y abuki, T. and Arizumi, Y. (1989) A Provision on Intermediate Diaphragm Spacing in Curved Steel- Plated Box-Bridge-Girders, Structural Engineering and Earthquake Engineering, JSCE, Vol. 6, NO. 2, pp. 207s-216s
  9. 마이다스아이티 (2006) Analysis for Civil Structures