• Analytical Science and Technology
• /
• 제12권3호
• /
• pp.190-195
• /
• 1999

The metabolism of testosterone ($17{\beta}$-hydroxy-androst-4-en-3-one) was confirmed in horse after a single intramuscular administration of testosterone cypionate (750 mg). Solvent extracts of urine obtained with enzymatic hydrolysis and methanolysis were analyzed by GC/MS after oxime t-butyldimethylsilyl (oxime-TBDMS) derivatization. The structures of four urinary metabolite after testosterone administration in horse were determined based on EI mass spectra and $5{\alpha}$-androstane-$3{\beta}$, $17{\alpha}$-diol and $5{\alpha}$-androstane-$3{\beta}$-ol-17-one as major was confirmed with authentic standard. Also the concentrations of $5{\alpha}$-androstane-$3{\beta}$, $17{\alpha}$-diol, $5{\alpha}$-androstane-$3{\beta}$, $17{\beta}$-diol, dehydroepiandrosterone (DHEA), $5{\alpha}$-androstane-$3{\beta}$-ol-17-one and testosterone were determined in the urine of normal subjects and the urine after administration. The recovery and detection limit in the most drugs were 86.3~94.7% and 1~3 ppb, respectively. Correlation coefficients for calibration were in the range of 0.984~0.999. Excretion profile of testosterone presents the rapid and large increasement up to maximum values at days 5 after administration and the slow regression. The relative ratios of testosterone, its metabolites over DHEA were determined for indication of testosterone administration in horse doping.

• Journal of Sensor Science and Technology
• /
• 제10권6호
• /
• pp.328-337
• /
• 2001

The stochiometric mix of evaporating materials for the $CdGa_2Se_4$ single crystal thin films was prepared from horizontal furnace. To obtain the single crystal thin films, $CdGa_2Se_4$ mixed crystal was deposited on thoroughly etched semi-insulating GaAs(100) substrate by the Hot Wall Epitaxy (HWE) system. The source and substrate temperature were $630^{\circ}C$ and $420^{\circ}C$, respectively. The crystalline structure of single crystal thin films was investigated by the photoluminescence and double crystal X-ray diffraction (DCXD). The carrier density and mobility of $CdGa_2Se_4$ single crystal thin films measured from Hall effect by van der Pauw method are $8.27{\times}10^{17}cm^{-3}$, $345\;cm^2/V{\cdot}s$ at 293 K, respectively. From the photocurrent spectrum by illumination of perpendicular light on the c-axis of the $CuInSe_2$ single crystal thin film, we have found that the values of spin orbit splitting ${\Delta}So$ and the crystal field splitting ${\Delta}Cr$ were 106.5 meV and 418.9 meV at 10 K, respectively. From the photoluminescence measurement on $CdGa_2Se_4$ single crystal thin film, we observed free excition ($E_x$) existing only high quality crystal and neutral bound exiciton ($D^{\circ}$, X) having very strong peak intensity. Then, the full-width-at -half-maximum(FWHM) and binding energy of neutral donor bound excition were 8 meV and 13.7 meV, respectivity. By Haynes rule, an activation energy of impurity was 137 meV.

• Analytical Science and Technology
• /
• 제18권3호
• /
• pp.201-205
• /
• 2005

Tri-octyl amine (TOA) is used in solvent extraction process for radioactive waste. This compound may be degraded to di-octyl amine (DOA), mono-octyl amine (MOA) by radioactive materials. Amount of TOA, DOA and MOA in TOA must be monitored because they production of these compounds means degradation of which leads to a decrease in the extraction yield. Retention behavior for TOA, DOA and MOA are studied with Phenomenex LUNA-$C_{18}$ ($4.6mm{\times}25cm$) analytical column and $CH_3OH:H_2O$ (50 mmol $CH_3COONH_4$) eluent by liquid chromatography. Optimum condition for these compounds is $CH_3OH:H_2O$ (50 mmol $CH_3COONH_4$) = 85 : 15 ratio. TOA, DOA and MOA compounds is well separated within 20 minute. Dynamic range is $30{\sim}160{\mu}g/mL$ for TOA, $5{\sim}100{\mu}g/mL$ for DOA and $0.1{\sim}5{\mu}g/mL$ for MOA, respectively. The detection limit are $0.1{\mu}g/mL$ for TOA, $1{\mu}g/mL$ for DOA (in SCAN mode) and $0.1{\mu}g/mL$ for MOA (in SIM mode) in this system with $20{\mu}L$ sample loop.

• Proceedings of the Korean Society of Broadcast Engineers Conference
• /
• 한국방송공학회 2002년도 정기총회 및 학술대회
• /
• pp.139-143
• /
• 2002

1990 년대 후반부터 다양한 디지털 통신망을 이용하여 멀티미디어 컨텐츠 서비스가 가능하게 되었다. 하지만, 멀티미디어 컨텐츠의 전달 및 이용을 위한 기반 구조들의 독자적 발전 및 다양한 통합적 관리 체계 시스템으로 인해, 멀티미디어 컨텐츠 표현 방식의 호환성 문제, 혼재하는 네트워크 전달 방식과 단말 방식의 호환성 문제 등의 잠재적인 문제점이 발생한다. 이런 문제의 대안으로 현재 존재하는 기술 및 기반 구조들 사이의 연동을 통한 큰 프레임워크인 MPEG-21이 진행 중이다. MPEG-21 의 목표는 표준화 목표를 구체화하는 것부터 진행하여, 최종적으로 “다양한 네트워크 환경과 단말기에 있어서, 투명하고 통합적으로 멀티미디어 자원의 이용을 가능하게 하는 것”이다. 본 논문에서는 현재 표준화 작업이 진행 중인 MPEG-21 을 기반으로 하는 Testbed를 제안한다. Testbed는 server, client, DIA(Digital Item Adaptation) 의 세 모듈로 구성된다. Server 의 역할은 멀티미디어 컨텐츠를 Digital Item(DI)으로 생성하고, client 가 DI를 요구할 경우 DIA 모듈을 통해서 변환된 DI를 client 에게 제공한다. DIA 모듈은 server 에서 동작되며 client로부터 요청된 DI를 분석하고 client로부터 전송된 환경 정보를 이용하여 client 환경에 적합하게 변환된 (adapted) DI를 생성하는 것이 주 기능이다. Client 는 server 에 저장되어 있는 DI를 선택하고 user preference, terminal capability 등의 필요한 정보를 server로 전송한다. Testbed 에서는 스포츠 경기의 동영상, 정지 영상, 경기 내용 역사를 기록한 파일 등의 DI를 이용한다. 표현 언어는 XML이며, HTTP 기반의 Web 환경에서 구동되도록 설계된다.스템 사이에 의미 있는 데이터 전송, 지식 획득을 위해 정보 기술 분야에서 활용해야 할 영역으로 XML Web Services, Multi-agent Systems, 전문가 컴뮤니티를 위한 그룹웨어 연구 개발에 관해 사례 중심으로 발표한다.다 신선한 공기를 넣어 주었을 때는 배의 발달이 많이 늦어져 배양 3주째에 다른 처리보다 배의 수가 훨씬 적었다. 체세포배가 발달하는 동안에는 산소를 많이 요구하지 않으나 성숙하는 동안에는 산소를 많이 요구하는 것으로 생각된다.적인 것으로 나타났다. 다만, 곡선형은 물론 직선형에서도 열교환 튜브의 배치밀도, 튜브 길이 및 두께 등의 변화에 따른 최적화 연구가 수반되어야 할 것으로 판단된다.에서 제공된 API는 객체기반 제작/편집 도구에 응용되어 다양한 멀티미디어 컨텐츠 제작에 사용되었다.x factorization (NMF), generative topographic mapping (GTM)의 구조와 학습 및 추론알고리즘을소개하고 이를 DNA칩 데이터 분석 평가 대회인 CAMDA-2000과 CAMDA-2001에서 사용된cancer diagnosis 문제와 gene-drug dependency analysis 문제에 적용한 결과를 살펴본다.0$\mu$M이 적당하며, 초기배발달을 유기할 때의 효과적인 cysteamine의 농도는 25~50$\mu$M인 것으로 판단된다.N)A(N)/N을 제시하였다(A(N)=N에 대한 A값). 위의 실험식을 사용하여 헝가리산 Zempleni 시료(15%$S_{XRD}$)의 기본입자분포로부터 %$S_{XRD}$를 계산한 결과, 16%$S_{XRD}$의 결과값을 얻을 수 있었다. 따라서, 본 연구에서 도출한 관계식들이 유효함을 확인할 수 있었다.계식들이 유효함을 확인할 수 있었다.할 때 약간의 증가

• Korean Journal of Environmental Agriculture
• /
• 제1권1호
• /
• pp.39-47
• /
• 1982

Dissolved oxygen, BOD and flow pattern of the Nakdong River stream were measured for 3 years from 1978 to 1980 at quarterly intervals of January, April, June and October at 12 sites along the main stream from Sangju to Imhaejin and at 2 sites of Geumho and Nam River tributaries. With these data, the self-purification factors of the river were computed to obtain the following results: 1) The average BOD loads per day at the tributary of Geumho River were 94 tons in January, 39 tons in April, 60 tons in July and 54 tons in October, and these are considered to be the main source of water pollution toward the main stream of the Nakdong River. 2) Self-purification factors for the Hwawon-Hyunpung region of the main stream after receiving Geumho River water were computed to give $0.21{\sim}0.59$ of deoxygenation $constant(K_1)$ and $0.56{\sim}2.27$ of reaeration $constant(K_2)$. The oxygen-sag curves constructed for the main stream showed a remarkable decline at Hwawon and a quick recovery at Hyunpung, indicating a rapid decomposition of pollution loads received from the Geumho River. It was confirmed that the self-purification capacity of the Nakdong River was relatively high.

• Journal of Korean Society of Environmental Engineers
• /
• 제27권5호
• /
• pp.525-534
• /
• 2005

A column experiment was performed to investigate the influence of the sludge cake development on the riverbed and the hydraulic gradient imposed by the drawdown at the well on the filtrate quality in order to offer a guideline in the design and operation of the riverbed filtration. Results show that the sludge cake on the riverbed plays an important role in the removal of the organic matter. Under the conditions of this study the COD removal rate increased from 17% to 50% along with the sludge cake development, which was equivalent to the BCOD removal of 22% and 67%, respectively. The active removal of the organic matter took place in the sludge cake and the upper 40 cm of the riverbed. As the flow rate increased owing to the increase in the head difference imposed on the column, the slope of the COD profile near the column inlet decreased, however, the profiles converged in about 40 cm from the inlet. In 10 days of sludge cake formation the dissolved oxygen was depleted at the depth of 70 cm, which suggests the denitrification can take place beyond the depth. This depth was further reduced to $20{\sim}40\; cm$ as the sludge cake developed. From this study the removal of organic matter can be expected through the riverbed filtration even with the depth of as shallow as 3 m, which is frequently met in Korea, while the removal of nitrogen through denitrification is not expected to be active under the condition.

• Journal of the Korean Applied Science and Technology
• /
• 제31권1호
• /
• pp.44-49
• /
• 2014

We were investigated by cyclic voltammetry to the stability through the electrochemical characteristics of phospholipid(L-${\alpha}$-phosphatidylethanolamine, LAPE) monolayer LB films. LAPE monolayer LB films was deposited by the LB method on the indium tin oxide(ITO) glass. The electrochemical properties was measured by cyclic voltammetry with a three-electrode system in 0.5 N, 1.0 N, 1.5 N and 2.0 N $KClO_4$ solution. The measuring range is continuously oxidized to 1650 mV, with an initial potential of -1350 mV was reduced. Scanning rates of 50, 100, 150, 200, and 250 mV/s was set. As a result, LB monolayer films of LAPE was appeared on irreversible processes by the oxidation current from the cyclic voltammogram. Diffusion coefficient (D) of LAPE was calculated 195, 15.9, 5.75, 1.38 and $0.754cm^2s^{-1}{\times}10^{-9}$ at 0.01 N, 0.05 N, 0.10 N, 0.15 N and 0.20 N $KClO_4$ solutions, respectively.

• Korean Journal of Food Science and Technology
• /
• 제37권1호
• /
• pp.30-37
• /
• 2005

To mass-produce useful biopolymer films, chitosan/gelatin blend films were prepared by solution casting method. Effects of mixing ratio, tensile strength (TS), elongation (E) at break, total color difference (${\Dalta}E$), opacity, water vapor permeability (WVP), oxygen permeability (OP), and thermal properties on chitosan/gelatin blend films properties were investigated. TS, E, ${\Dalta}E$, opacity, WVP, and OP values were 58.24-22.01 MPa, 13.11-24.67%, 1.86-17.45, 0.3104-1.2161 nmO.D./${\mu}m$, $1.6875-1.7225ng{\cdot}m/m^{2}{\cdot}s{\cdot}Pa$, and $2.2380{\times}10^{-7}-2.2975{\times}10^{-7}\;mL{\cdot}{\mu}m/m^{2}{\cdot}s{\cdot}Pa$, respectively. TS of blend films decreased, while E, ${\Dalta}E$, and opacity increased with increasing chitosan content. WVP of blend films did not show any significant relationship with mixing ratio and thickness of blend films. Miscibility of films was examined over entire composition range by thermogravimetric analyzer (TGA) and dynamic mechanical analyzer (DMA). TGA results showed gelatin is more thermally stable than chitosan and some interactions among functional groups of two biopolymers. Glass transition temperature $(T_{2})$ of films as determined by DMA decreased with increasing content of chitosan in the blend. Results of thermal analysis indicate high miscibility among polymer components in the blend.

• Journal of the Korean Electrochemical Society
• /
• 제7권2호
• /
• pp.100-107
• /
• 2004

The nano or micro sized structures of conducting polymer had been prepared by synthesizing the desired polymer within the pores of template of nano or micro porous membrane filter. In this study, we had tried to fabricate conducting polymer microstructures on an electrode by using electrochemical deposition adopting template synthesis. Our attention was focused on two different things, attaching template on the electrode and fabricating microstructures only at limited areas of the electrode. A conducting polymer, PEDiTT (poly 3,4-ethylenedithi-athiophene) solution was blended with PVA(polyvinyl alcohol) solution and used as an conducting adhesive. After attaching template membrane, the electrode were immersed in 0.5M pyrrole in 0.1M KCI solution, and electrochemical polymerization was performed. The growth process of the microstructures studied by SEM. The electrochemical fabrication of conducting polymer was performed by using two-electrode system. A large working electrode and a micro scale disc electrode were used for the confined area synthesis. Polymerization potential was 4V in an electrolytic solution made of KCI in deionized water. The optimum polymerization conditions were, i.e. (4V/100sec) for $250{\mu}m$ electrode and (6V/30 sec) for $10{\mu}m$ electrode.

• Journal of Sensor Science and Technology
• /
• 제8권5호
• /
• pp.359-367
• /
• 1999

CsI(Li) single crystals doped with 0.02, 0.1, 0.2 and 0.3 mole% lithium as an activator were grown by Czochralski method. The lattice structure of grown CsI(Li) single crystal was bcc, its lattice constant was $4.568\;{\AA}$. The absorption edge of CsI(Li) single crystal was 245 nm, and the spectral range of luminescence was $300{\sim}600\;nm$, its maximum luminescence intensity appeared at 425 nm. The energy resolutions of CsI(Li) single crystal doped with 0.2 mole% lithium were 14.5% for $^{137}Cs$(662 keV), 11.4% for $^{54}Mn$(835 keV) and 17.7% and 7.9% for $^{22}Na$(511 keV and 1275 keV), respectively. The relation formula of $\gamma$-ray energy versus energy resolution was ln (FWHM%) = -0.893lnE + 8.456 and energy calibration formula was ${\log}E_r=1.455\;{\log}(ch.)-1.277$. The phosphorescence decay time of CsI(Li) crystal doped with 0.2 mole% lithium was 0.51 s at room temperature, and its time resolution measured by CFT(constant-fraction timing method) was 9.0 ns.