• Fire Science and Engineering
• /
• v.16 no.1
• /
• pp.66-76
• /
• 2002

This paper includes new nozzle design, basic design factors of water mist system that minimize a thermal damage of cable causing business interruption and applying underground utility tunnel. A underground concrete structure (2.5 m(H)$\times$2.5 m(W)$\times$25 m(D)) is constructed in order to test a nozzle performance. Under the designing fire scenario, critical thermal damage of cable sheath ($400^{\circ}c$) reached within a 2 minutes with unsuppressed fire, but type 1 nozzle (SMD 470 $\mu{m}$) and type 2 nozzle (SMD 650 $\mu{m}$) control cable temperature below $400^{\circ}c$. A system performance and fundamental design factors; K factor, flow rate, spray angle, size distribution, nozzle pressure, spray density are analyzed and proposed for system optimization.

• Fire Science and Engineering
• /
• v.26 no.3
• /
• pp.8-13
• /
• 2012

This study suggests the water curtain nozzles as the way to protect important wooden cultural properties from an adjacent building fire or a forest fire. They are designed to block off the pyrolysis of timbers which occurs at $200{\sim}250^{\circ}C$ by forming a water curtain with the flow of water that spouts over a certain pressure from the bottom. The existing water curtain nozzles installed at the following sites were examined: NakSan-sa (Temple) in Gangwon-do (Province) and in Muwisa (Temple) in Jeollanam-do (South Province). As a way to improve and complement the system, this study designed nozzles with covers in order not to disrupt the landscape. Connected pipes are elevated and jet water when they are in use. Possible ways to install the connected elevating pipes to jet water effectively were investigated.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2010.11a
• /
• pp.177-180
• /
• 2010

Two-stage light gas gun, sorted with Ballistic Range System, is used to research spray characteristics of supersonic liquid jets. When high pressure tube was pressurized to the 135 bar, diaphragm films which composed with OHP film are ruptured. Expansion gases accelerate a projectile approximately 250 m/s at the exit of pump tube. And accelerated projectile collides with liquid storage part and liquid jets were injected into supersonic conditions. Supersonic liquid jets show the multiple jets and generate shockwave at the forward region of jets. Supersonic liquid jets of speed and shockwave angle have different value at each case. Supersonic liquid jets with minimum velocities are injected with M=1.53 at the geometry condition of L/d=23.8.

• Transactions of the Korean Society of Pressure Vessels and Piping
• /
• v.14 no.1
• /
• pp.58-65
• /
• 2018

The purpose of this study is to develop a Half Nozzle Repair(HNR) process to prevent the leakage from welds on small bore piping in Reactor Coolant System. The Codes & Standards of tempered bead and design requirements of J-Groove welds are reviewed. Automatic machine GTAW welding and machining equipments are developed to perform HNR process. Single pass welding and overlay welding equipments are conducted in order to obtain the optimal temper bead welding process parameters with Alloy 52M filler wire. Coarse grain heat affected zone(CGHAZ) is formed by rapid cooling rate in heat affected zone after welding. Accordingly, a proper temper bead technique is required to reduce CGHAZ in 1-Layer of welds by 2- and 3-Layers. Mock-up tests show that the developed HNR process is possible to meet ASME Code & Standard requirements without any defect.

• Fire Science and Engineering
• /
• v.16 no.4
• /
• pp.33-43
• /
• 2002

To analyze the effect of fire plume on the characteristics of air flow and $CO_2$, extinguishant transfer when extinguishant is injected into a closed space similar to a marine engine room with fire plume, a numerical simulation on a space was performed. Flow fields and $CO_2$, concentration fields are calculated according with the variation of the location of nozzles. In all cases excepting the case of all nozzles located in the right side of ceiling, an counterclockwise & clockwise recirculation flow was found in the region of the right and left side of the nozzle on the second floor and such a recirculation flow greatly affected mass transfer and the diffusion process of $CO_2$, extinguishant. In the region of the first floor with fire plume, the diffusion process of $CO_2$, extinguishant was in agreement with the extension process of recirculation flow. It is considered that the result of this study can be useful to designing the arrangement of nozzles for the $CO_2$ fire fighting equipments in a marine engine room.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.23 no.1
• /
• pp.25-36
• /
• 2021

Hydrogen in hydrogen-electric vehicles has a wide range of combustion and explosion ranges, and is a combustible gas with a very fast flame propagation speed, so it has the risk of leakage, diffusion, ignition, and explosion. The fuel tank has a Thermally active Pressure Relief Device (TPRD) to reduce the risk of explosion and other explosions, and in the event of an accident, hydrogen inside the tank is released outside before an explosion or fire occurs. However, if an accident occurs in a semi-closed space such as an underground parking lot, the flow of air flow is smaller than the open space, which can cause the concentration of hydrogen gas emitted from the TPRD to accumulate above the explosion limit. Therefore, in this study, the leakage rate and concentration of hydrogen over time were analyzed according to the diameter of the nozzle of the TPRD. The diameter of the nozzle was considered to be 1 mm, 2.5 mm and 5 mm, and ccording to the diameter of the nozzle, the concentration of hydrogen in the underground parking lot increases in a faster time with the diameter of the nozzle, and the maximum value is also analyzed to be larger with the diameter of the nozzle. In underground parking lots where air currents are stagnant, hydrogen concentrations above LFL (Lowe Flammability Limit) were analyzed to be distributed around the nozzle, and it was analyzed that they did not exceed UFL (Upper Flammability Limit).

• Proceedings of the Korean Society for Bio-Environment Control Conference
• /
• 1992.12a
• /
• pp.29-30
• /
• 1992

최근 근권의 산소부족 문제를 근본적으로 해결할 수 있는 수경능법으로서 분무경에 관한 관심은 매우 높으며 분무경의 우수성이 실증적으로 제시되고 있으나 분무경의 경우 고압을 필요로 하므로 장치가 복잡해지거나 엽체류의 경우 분무노즐과의 거리에 따라 생장이 균일하지 않는 문제점을 갖고 있으므로 분무경과 같이 근권산소 문제를 근본적으로 해결하는 효과를 가지면서도 취급 및 관리가 편리한 수경시스템의 개발이 절실히 요구되고 있다. (중략)

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1993.04b
• /
• pp.66-70
• /
• 1993

미세드릴가공은 드릴 직경의 소경화로 발생하는 공구강성저하, 지동 발생, 칩배출 곤란 등으로 인해 수많은 기계가공 중에서도 가장 어려운 가공 중의 하나이며 이로인해 설계의 단계에서 가능한 피하고있는 실정이다. 그러나 근래 각종 제품의 소형 경량화 추세가 일어나면서 미세구멍가공 기술에 대한 중요성이 높아지고 있으며, 특히 시계부품, 소형 정밀 부품, 연료분사용 노즐, 광파이버 관련품, 우주항공기 부품 등에 수요가 급증하고 있다. 또한 최근 전기.전자 공업의 발달과 함께 등장한 표면실장기술(SMT)은 프린터 배선기판의 고밀도화를 더욱 진전시켰으며 이는 구멍밀도, 구멍지름의 미소화 등 미세구멍가공 관점에서 보완해야 할 기술적인 과제를 남겨 놓았다. 본 연구는 미세드릴가공의 메카니즘을 규명하고 그 문제점을 해결하여 미소경 드릴링 머신을 개발하는 데 주력함과 동시에그 절삭현상의 기초적인 연구를 수행하였다

• Journal of the Korean Society for Precision Engineering
• /
• v.33 no.1
• /
• pp.31-35
• /
• 2016

For reaction injection molding (RIM) polyurethane was mixed in the mixing head by impingement mixing, injected into the mold, and cured quickly, as soon as the mold is filled. The shape of the nozzle in the mixing head is critical to improve the quality of polyurethane. To achieve homogeneous mixing, an intensive turbulence energy in the mixing nozzle is essential. In this study, a mixing nozzle for RIM was designed, and mixing efficiency was investigated based on experiment. Experiments were conducted with different combinations of nozzle tips and exit diameter to measure the mixing efficiency by measuring jet force and investigating mixing image with high speed camera. Jet force increased gradually and reaches steady state conditions. The jet force depended on shape of nozzle tip and outlet sizes. These results suggest that optimized nozzle configurations are necessary for high efficiency mixing with RIM.

• Journal of Power System Engineering
• /
• v.11 no.1
• /
• pp.82-91
• /
• 2007

기존의 2차원 FDLB 모델(D2Q21)에서 비열비 ${\gamma}$는 공간의 차원수(D)에 의존한다. 즉, 2차원 공간의 계산에서는 ${\gamma}=(D+2)/D=2.0$밖에 취할 수 없으며, 공기와 같은 실체기체를 전산모사 하기에는 여러 어려움이 있다. 이러한 이유 때문에 문헌[1]의 LBM에서 제안된 조정 가능한 비열비 모델을 2차원 FDLB모델에 적용하여 자려발생 에지톤(edgetone)의 수치계산이 수행되었다. wedge의 선단각도가 ${\alpha}=23^{\circ}$(Case I) 및 $20^{\circ}$(Case II)를 갖는 2가지 모델이 설정되었으며, 노즐출구에서 wedge선단까지의 거리 w/d는 $3d{\sim}12d$사이에서 주어졌다. edgetone은 노즐로부터 나온 분류와 edge의 상호작용으로 이난 음압(sound pressure)의 차에 의해서 소음이 발생하며, 이 음압은 다시 상류의 분류에 영향을 미쳐 분류의 변동을 가져온다. w/d가 ??9d이하인 경우, 피드백(feedback) 메커니즘에 기인한 주기적인 운동이 발생하지만, w/d가 큰 ??9d이상인 경우에는 분류의 불안정성 때문에 규칙적인 분류의 운동은 보이질 않으며, 이는 기존의 연구결과들과 잘 일치함을 보였다. 본 연구에서 적용된 모델을 이용하여 공기와 같은 2원자 기체의 비열비 ??${\gamma}=1.4$를 갖는 유체에 있어서 공력 소음의 수치예측이 가능하다는 것을 확인하였다.