• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.17 no.2
• /
• pp.152-167
• /
• 2018

The high-speed weigh-in-motion system can collect the traveling speed and load information of individual vehicles, which can be used in a variety of ways for the traffic surveillance. However, it has a limit to apply the high-speed weigh-in-motion data directly to a safety analysis because high-speed weigh-in-motion's raw data are point measured data. In order to overcome this problem, this paper proposes a method to calculate the conflict rate and the Impulse severity based on surrogate safety measures derived from the detection time, detection speed, vehicle length, vehicle type, vehicle weight. It will be possible to analyze and evaluate the risk of rear-end collision on freeway traffic. In addition, this study is expected to be used as a fundamental for identifying crash risks and developing policies to enhance traffic safety on freeways.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.14 no.2
• /
• pp.95-107
• /
• 2002

A reliability analysis on sliding of monolithic vertical caisson of composite breakwaters is extensively carried out in order to make the basis for the applicability of reliability-based design method. The required width of caisson of composite breakwaters is determined by the deterministic design method including the effect of impulsive breaking waves as a function of water depth, also studied interactively with the results of reliability analyses. It is found that the safety factor applied in current design may be a little over-weighted magnitude for the sliding of caisson. The reliability index/failure probability is also seen to slowly decrease as the water depth increases for a given wave condition and a safety factor. In addition, optimal safety factor can roughly be evaluated by using the concept of target reliability index for several incident waves. The variations of optimal safety factor may be resulted from the different wave conditions. Finally, it may be concluded from the sensitivity studies that the reliability index may be more depended on the incident wave angles and the wave periodsrather than on the bottom slopes and the thickness of rubble mound.

• Journal of the Korea Institute of Building Construction
• /
• v.23 no.6
• /
• pp.715-726
• /
• 2023

This study suggested that protective panels should be installed as sacrificial members as a safety design method for structures with potential explosions such as hydrogen charging stations to minimize direct damage to the structure and have resilience. To this end, the focus of the experiment is on quantitatively evaluating the impact of the structure when the protection panel is installed closely or spaced apart from the structure in a high-speed collision situation of the projectile. The experimental design used steel plates instead of concrete structural members mainly used in the past for excellent reproducibility, and the impact of structural members was compared and analyzed through deformation differences on the back of the steel plate. In addition, the impact of changes in the physical properties of the elastic body used as a separation material for the protective member and the difference in shock wave transmission time according to the protective member and the elastic body on the structural member was investigated.

• Proceedings of the Korean Reliability Society Conference
• /
• 2011.06a
• /
• pp.131-140
• /
• 2011

도로안전시설용 시선유도봉은 통상 도로에 설치되어 운전자의 시선을 유도하고 차선을 분리하는 용도로 사용된다. 이러한 시선유도봉은 주로 도로상에 설치되기 때문에 차량과 부딪히는 경우가 자주 발생하므로 제품의 내구성이 특히 요구된다. 종래의 시선유도봉에 대한 평가방법은 제품의 일부를 채취하여 재료의 기본 품질 성능만을 평가하였다. 그러나 현장의 도로관리를 담당하고 있는 수요기관에서는 빈번한 사고와 민원으로 인해 제품의 평가방법에 대한 문제 제기를 하였고, 완제품 상태로 신뢰성을 평가할 수 있는 방법 개발을 요구하였다. 따라서 본 연구에서는 시선유도봉의 주요 고장 요인이 되는 차량 충돌에 의한 재질 파손, 바퀴 압축에 의한 회복 불능, 제품 표면에 부착되는 반사시트의 박리 및 변색에 대한 고장 메커니즘 분석하고, 이러한 고장을 재현할 수 있는 신뢰성 평가법을 개발하고자 하였다. 주요 고장 메커니즘 분석을 위해 국내.외 평가 기준을 조사하였으며, 특히 미국 AASHTO's (American Association of State Highway and Transportaion Officials)의 NTPEP (National Transportation Products Evaluation Program)에서 수행하고 있는 내구성 평가 방법에 대한 사례 조사를 통해 국내 적용을 검토해 보았다. 또한 서울시설관리공단의 협조로 가장 주요한 고장의 요인으로 꼽히는 차량 충돌 시험을 올림픽대로 내 조각공원에서 실시하였다. 그 결과 시험실에서 고장을 재현할 수 있는 신뢰성 평가 장비 개발의 필요성이 부각되었으며, 차량 충돌과 바퀴 압축을 모사할 수 있는 신뢰성 평가 장비를 제작하였다. 시선유도봉의 신뢰성 평가는 기본적인 품질성능평가 이외에 신규로 개발된 충격시험(고온, 저온, 반사지)과 굴곡압축시험, 반사지와 재질의 내후성 시험을 실시하였다. 또한 국내 9개사(社) 10개 제품에 대한 신뢰성 비교평가를 실시한 결과, 제품의 내구성에 중요 척도가 되는 신뢰성 평가 기준을 설정할 수 있었고, 합리적인 제품의 가격 수준과 품질 수준에 대한 신뢰성 가이드를 제공할 수 있었다.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.25 no.9
• /
• pp.1661-1668
• /
• 2001

본고는 지뢰 방호복을 개발, 국산화하기 위해 먼저 방탄소재 구성방법에 관하여 실험한 결과이다. 기존의 여러 겹의 파라-아라미드(Para-aramid)나 단순히 파라-아라미드와 폴리 에틸렌 필름(Polyethlene film)을 조합한 소재구성과는 달리 케블라 파이버(Kevlar fiber)로 만들어진 펠트(felt)를 첨가하여 방탄원리 및 특성을 고려한 구성으로 방호복의 중량을 줄이면서 착용자로 하여금 유연성과 동작성을 향상시켜 임무수행과 안전성을 높일 수 있는 방호복을 개발하고자 하였다. 1) Para-aramid(내 충격열) + Flex-felt(충격 에너지 흡수) + Para-aramid(backface Polyethylene film(에너지 분산 극대)+Para-aramid(내 마찰열, backface순으로 소재를 배열함으로써 기존의 Para-aramed 36겹에 대하여 Para-aramid13겹, Polyethylene film 13겹, 그리고 펠트 1겹으로 동일한 방호성능을 얻었다. 2) 새로운 소재 구성 방법 에 의 한 방탄소재는 동일한 방호성능을 갖는 기존의 소재 구성 방법 에 따른 방탄소재 보다 중량에서 34-l9% ,더 가벼운 것으로 나타나 방호복 구성시 유연성이나 동작성에 유리 할 것으로 사료된다. 3) NIJ-STD-0101.03에서 의 Armor type II에 해당하는 시편 I의 방호한계속도로 구한 운동 에너지량은 154.4J Armor type III-A에 해 당하는 시편II의 방호한계속도로 구한 운동 에너지 량은 183.0J로 나타나 두 시편 모두 5m의 거리에서 M16Al지뢰의 0.032~0.044g사이 의 파편에 대해서 50%의 관통확률을 갖는 것으로 나타났다.

• Journal of the KSME
• /
• v.37 no.10
• /
• pp.41-46
• /
• 1997

철강구조물 부재 내에 노치나 균열이 존재할 수 있고, 외부의 피로하중에 의하여 취약부에서 발생한 균열이 진전하여 전구조물의 최종파손을 야기시킬 수 있다. 부재를 보다 안전하게 사용하고 또한 신뢰성을 확보하기 위해서는 이미 손상된 부재에서 균열의 진전상태를 계측할 수 있는 방법이 확립되어져야 하고, 파괴역학적 파라미터를 이용한 사용재의 균열진전거동특성이 평가되어야 한다. 균열길이의 측정방법은 지금까지 많은 연구자들에 의하여 개발되어져 왔는데 크게 광학현미경을 이용하여 육안으로 직접 균열길이를 측정하는 방법과 컴플라이언스, 초음파, AE 또는 전기적 신호를 통하여 얻어진 결괄부터 균열길이로 환산하는 간접적인 방법으로 대별된다. 대부분의 균열길이의 측정방법은 많은 수작업이 요구되고, 특히 하한계응력확대계수영역의 미세한 균열진전량을 측정하기에는 어려움이 따르고 있다. 이에 대하여 전도체 시험편에 일정전류를 흐르게 하고 균열길이의 증가에 따라 변화하는 전위차로 이를 균열길이로 평가하는 전기적인 측정방법이 있다. 이 방법은 실험장치가 비교적 간단하고 미세한 균열길이의 측정이 용이하여 균열길이의 직접적인 측정이 곤란한 고온역 그리고 충격하중하에서의 균열길이 측정에 이용이 확대되고 있다. 이 글에서는 여러 균열길이 측정방법의 장.단점에 대하여 고찰하고, 그 중 많은 장점을 갖고 있는 직류전위차법의 실험방법을 소개한다.

• Journal of Korean Ophthalmic Optics Society
• /
• v.16 no.3
• /
• pp.229-235
• /
• 2011

Purpose: The present study was performed to evaluate the safety of ophthalmic lenses in domestic market since eyeglasses wearers could be exposed to the negligent accident by damaged ophthalmic lenses. Method: Totally, 160 ophthalmic lenses (NK55, ${n_{d}}$ = 1.56) with the refractive powers of -3D, -6D, +3D, +6D manufactured by 4 companies in domestic market were evaluated using drop ball test. In accordance with FDA standard, steel ball (~16 g) was freely dropped on these ophthalmic lenses from 127 cm high and the surfaces of lenses were observed. Results: From the study, center thicknesses of NK55 ophthalmic lenses manufactured by 4 different companies showed somewhat different numbers even though the lenses had the same refractive index and powers. All convex lenses of +3D, +6D were evaluated as the safe lenses since there was no damage such as crack and broken found on the lens surfaces after drop ball testing. However, some noticeable broken was shown on the surfaces of concave lenses with relatively thinner center thickness. Especially, 59(73.8%) of total 80 concave lenses with the refractive power of -3D and -6D classified as unacceptable lenses to FDA standard. Conclusions: From the results, the negligent accident by damaged ophthalmic lenses should be considered as well as the correction of visual acuity, design and price when customers purchase eyeglasses. Thus, the enforcement regulation like drop ball testing of uncut ophthalmic lens could be suggested to guarantee the safety of ophthalmic lenses in domestic market.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.31 no.2
• /
• pp.139-143
• /
• 2011

The problem of delamination of composite tubes by impact has been acknowledged in aerospace and automobile industry. Non-destructive testing(NDT) methods in composite material structure are important to evaluate reliability of composite structure. There are many kinds of NDT methods which can detect the inside defect of the composite material such as Infrared Thermography(IRT). Infrared thermal imaging of object is different from that of a defect, in heated composite tubes with an internal defect, and then location and size of a defect can be measured by the analysis of thermal imaging pattern. In this study, Lock-in Infrared thermography detect internal defects of Impacted composite tubes by the inspection of infrared lay radiated from the surface of composite tubes.

• Journal of the Korean GEO-environmental Society
• /
• v.21 no.5
• /
• pp.23-33
• /
• 2020

As the scale of the economy expands, the number of cases of damage in enclosed spaces such as tunnels is increasing due to the accident of transportation vehicles of dangerous substances such as explosive flammable materials that have increased rapidly. In the case of road tunnels in particular, in the aspect of protection against the long-winding trend and the environment in the downtown area, the number of cases of passing through the downtown area increases, and securing the safety of structures against unexpected extreme disasters such as explosions during tunnel passage is very urgent. For this reason, developed countries are already conducting a review of internal bombardment, but there are almost no evaluation and countermeasures for explosion risk in Korea. Therefore, in this study, in order to evaluate the explosion safety of road tunnels, a boiling liquid explosive explosion (BLEVE), which is considered to have the greatest explosion load among vehicles driving on the road, is set as a reference explosion source, and the equivalent TNT explosion load is used for simulation of the explosion. A method of conversion was presented. In addition, by applying the derived explosion load, dynamic behavior simulation was performed by assuming various variables for the tunnel, and the explosion safety of the tunnel was analyzed.

• Tunnel and Underground Space
• /
• v.24 no.3
• /
• pp.187-200
• /
• 2014

After excavation or blasting, rock properties within an excavation damaged zone can be perpetually weakened on account of stress redistribution or blasting impact. In the present study, the excavation damaged zone is applied to a rock slope. The objective of this research is to compare the mechanical stability of the rock slope depending on the presence of the damaged zone using 2-dimensional modeling and analyze factors affecting factor-of-safety. From the modeling, it was founded that the mechanical stability of the rock slope is significantly dependent on the presence of the damaged zone. In particular, factor-of-safety with a consideration of the damaged zone decreased by approximately 49.4% in comparison with no damaged zone. Factor analysis by fractional factorial design was carried out on factor-of-safety. It showed that the key parameters affecting factor-of-safety are angle of the slope, cohesion, internal friction angle and height.