• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.43 no.10
• /
• pp.868-874
• /
• 2015

Thrust variation is an essential parameter in a space mission such as landing on an atmosphereless planet or docking a spacecraft. In order to achieve the thrust variation control, using throttleable injector is a representative and general method. A dual-manifold injector, one of throttleable injectors, was used to control mass flow rate. Five kinds of injectors were designed and investigated in order to compare the spray characteristics of the dual-manifold injector with various tangential entries. Spray angles and patterns were measured to determine external flow characteristics and film thicknesses were measured in order to investigate the internal flow patterns.

• Journal of Hydrogen and New Energy
• /
• v.33 no.1
• /
• pp.47-54
• /
• 2022

In this study, we performed numerical analysis for 1 kWe SOFC stack of internal manifold types according to the different manifold sizes to verify the influence of the flow uniformity into each cell. To simulate the flow phenomena in the stack, the continuity and momentum conservation equations including the standard k-𝜺 turbulent model for the steady-state conditions were applied. From the calculation results, we verified that the pressure drop from inlet pipes to outlet pipes decreased to a log scale as the manifold size increased in the internal manifold types. Also, we found that the flow uniformity increased on an exponential scale as the manifold size increased. In addition, the calculation results showed that the flow uniformity gradually improved as the fuel and oxygen utilization increased.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.8 no.2
• /
• pp.1-9
• /
• 2004

The flow in the LOX manifold of liquid rocket (KSR-III) has been analyzed using a CAE technique with an objective of modeling injector orifices in order to reduce the computational cost for the flow analysis without much losing the accuracy of capturing the flow physics. The numerical result shows that the flow just above the injector orifices is not uniformly distributed in terms of pressure and mass flow rate in case pre-distributors are not equipped inside the manifold. This non-uniformity of mass flux is attributed to the presence of large-scale flow patterns. Several boundary conditions which were designed to effectively replace the presence of injector orifices have been tested and it was found that a simple modeling can be possible by mimicking the actual shape of the orifices.

• Aerospace Engineering and Technology
• /
• v.1 no.2
• /
• pp.113-122
• /
• 2002

A numerical analysis on the uniformity of propellant injection velocity of KSR-III has been carried out to give design improvements. Injector holes were approximated as porous media with the same pressure drop . The injection velocity is higher at the opposite side of the inlet for both LOX and fuel due to the static pressure rise in the stagnation region. Flow passages at the vertical circular plate in the LOX dome increase the uniformity of LOX injection. Little change was observed in the injection uniformity and pressure drop for the slanted LOX passage. Also provided were the O/ F ratio distributions from the oxidizer/ fuel injection velocity analysis.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.19 no.5
• /
• pp.22-30
• /
• 2015

A gas generator which generates turbine driving gas by burning a part of propellants is used in an open cycle liquid rocket engine and as a main component of an open cycle liquid rocket engine autonomous hot firing tests are required to investigate the combustion performance and characteristics of the gas generator. However, since the combustion gas generated by a gas generator is choked at the turbine nozzle in the turbine manifold, it is necessary to consider the internal volume of turbine manifold as well as that of the gas generator for correct investigation of the combustion performance, characteristics, and acoustic characteristics of the gas generator. Therefore, in the paper hot firing test results of a gas generator with a turbine manifold simulator are described and characteristic prediction using the autonomous test of a gas generator is explained.

• Elastomers and Composites
• /
• v.49 no.4
• /
• pp.275-283
• /
• 2014

Butyl rubber is used as an adhesive and it is mainly used in the form of sheets. The goal of this study is to design an extrusion die for the butyl rubber sheets using computer simulation. The extrusion die for the butylrubber sheets consists of manifold area and land area. In the manifold area, flows are spread from the entrance of the extrusion die to the land area. In the land area, flows become stable to the flow direction and uniform sheet can be obtained. Island area is being installed in the land area to get uniform flow. Four parameters, angle of manifold, length of manifold, length of land and island, were examined in the computer simulation. The optimum geometry of the extrusion die is derived which has a uniform flow in the width direction of the die.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2010.05a
• /
• pp.29-33
• /
• 2010

This study aim to investigate the internal flow characteristics by recess length of swirl coaxial injector for gas generator has propellant of Kerosene-LOx. Recess length is a very important element, have influence in spray stability and LOx post damage. The influence of recess length was analyzed by visualizing internal flow and measuring liquid film thickness and manifold pressures. Also, each spray characteristic by recess length was investigated in internal or external injector.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.11 no.5
• /
• pp.72-77
• /
• 2007

The combustion test results of the sub-scale combustor having dual swirl injector with internal mixing for a liquid rocket engine are described. The sub-scale combustor uses liquid oxygen(LOx) and kerosene as propellants and has an injector head, an ablative material combustor wall and a water cooled nozzle. The injector head has LOx manifold, fuel manifold, fire face plate, one center swirl injector and 18 main swirl injectors of internal mixing. The combustion tests were successfully performed at design and off-design points without any damages on the injectors. Combustion characteristics velocity of 1756m/s was measured at design point. High frequency combustion instability was not observed but low frequency pulsations occurred at off-design conditions.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2010.11a
• /
• pp.13-18
• /
• 2010

This study aim to investigate the internal mixing flow characteristics by recess length of swirl coaxial injector for gas generator has propellant of Kerosene-LOx. Recess length is a very important element, have influence in spray stability and LOx post damage. The influence of recess length was analyzed by visualizing internal flow and measuring liquid film thickness and manifold pressures. Also, frequency characteristics were analyzed by liquid film thickness measurement with mixing time.

• Aerospace Engineering and Technology
• /
• v.4 no.2
• /
• pp.135-141
• /
• 2005

The procedure of conceptual and detailed design of sub-scale combustor using bipropellant swirl or impinging injector with external or internal mixing for a liquid rocket engine are described in this paper. The sub-scale combustor uses liquid oxygen(LOx) and kerosene as propellants and has a injector head, an ablative material combustor wall and a water cooled nozzle. The injector head has LOx manifold, fuel manifold, fire face plate, one center swirl or impinging injector and 18 main swirl or impinging injectors.