• Journal of Biomedical Engineering Research
• /
• v.21 no.6
• /
• pp.599-606
• /
• 2000

고정체 나사산 형상이 식립된 고정체를 둘러싸고 있는 턱 뼈에서 발생된 응력분포에 미치는 영향과 효과적인 나사산 형상을 결정하기 위해서 다양한 치아 고정체 형상에 대해서 응력해석을 수행하였다. 나사산 골 한쪽 부위에 라운딩이 된 형상의 고정체에서 발생된 응력분포는 다른 나사산 형상의 고정체에서 발생된 응력분포보다 더 효과적으로 나타났다. 이 해석 결과를 근거로 최적의 고정체 치수를 결정하기 위해서 나사산 끝단의 폭, 나사산 높이, 그리고 가해지는 하중의 방향 등과 같은 설계 변수의 변화에 따른 응력해석이 수행되었다. 최대 응력 집중은 고정체 나사산의 첫단 부위에서 발생하였으며, 100 N의 15도 경사하중이 가해졌을 때 발생된 최대 등가응력은 동일 크기의 수식하중보다 2배 정도 더 높게 나타났다. 그리고 나사산 끝단의 폭과 나사산 높이 사이의 연관성에 관련된 해석결과에서 나사산 끝단의 폭과 나사산 높이 사이의 연관성 효과는 무시할 만큼 작다는 것을 알았다. 고정체의 나사산 피치에 대한 나사산 끝단의 폭의 비와 나사산 높이의 비가 각각 0.5와 0.46일 때 다른 고정체의 치수들보다 더 효과적인 응력분포가 나타났다

• The Journal of Korean Academy of Prosthodontics
• /
• v.52 no.4
• /
• pp.279-286
• /
• 2014

Purpose: The aim of this study was to investigate the effect of implant thread profile on the marginal bone stresses which develop during implant insertion. Materials and methods: Four experimental implants were created by placing four different thread systems on the body ($4.1mm{\times}10mm$) of the ITI standard implant. The thread types studied in this study included the buttress, v-shape, reverse buttress, and square shape threads. In order to examine the insertion stress generation, 3D dynamic finite element analysis was performed which simulated the insertion process of implants into a 1.2 mm thick cortical bone plate (containing 3.5 mm pilot hole) using a PC-based DEFORM 3D (ver 6.1, SFTC, Columbus, OH, USA) program. Results: Insertion stresses higher than human cortical bone developed around the implants. The level of insertion stresses was much different depending on the thread. Stress level was lowest near the v-shape thread, and highest near the square shaped thread. Difference in the interfacial bone stress level was more noticeable near the valley than the tip of the threads. Conclusion: Among the four threads, the v-shape thread was turned out to minimize the insertion stress level and thereby create better conditions for implant osseointegration.

• Journal of the Korean Society for Precision Engineering
• /
• v.32 no.6
• /
• pp.503-507
• /
• 2015

In this study, we compare the performance of the screw through the Clamping force of the test materials to change shape and structure, one of the ways to maintain and improve the engaging force to cope with the miniaturization of the fastener threads are further thinner and lighter precision way that can improve the fastening force of the screw results were as follows. The clamping force according to the materials was $7.57N{\cdot}cm$ in SUS XM7 and SWCH18A was $5.97N{\cdot}cm$. This result was to be found to average 13.5% high in the Clamping force of SUS XM7 materials. In the case of the clamping force of the screw thread shape change, the clamping force of symmetrical and asymmetrical thread was $6.78N{\cdot}cm$ and $7.57N{\cdot}cm$. The clamping force of the asymmetrical thread showed an average high of 11.6%.

• Journal of the Korean Society for Precision Engineering
• /
• v.31 no.9
• /
• pp.839-846
• /
• 2014

Recent trends in the miniaturization and weight reduction of portable electronic parts have driven the use of subminiature screws with a micrometer-scale pitch. As both screw length and pitch decrease in subminiature screws, the resulting clamping force becomes diminishes. In this work, Finite element (FE) analysis is performed to evaluate clamping force of a screw assembly, with a comparison with experimental result. To improve clamping force of subminiature screws, a new screw design is considered by modifying screw thread angle: the thread angle is varied as an asymmetric way unlike the conventional symmetric thread angle. FE analyses are then performed to compare the clamping characteristics of each subminiature screw with different thread angle. The effect of thread angles on the clamping force is then discussed in terms of structural safety for both positive and negative screws.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2018.06a
• /
• pp.86-86
• /
• 2018

볼트, 너트 등의 파스너는 건축 재료나 기계부품을 고정하는 데 사용하는 기계요소로, 건축, 철도, 조선 등 전 산업분야에 걸쳐 사용되고 있다. 그 중 스테인리스 소재의 볼트, 너트는 뛰어난 내식성과 저렴한 가격으로 널리 사용되고 있는데, 소재의 특성 및 작업현장의 상황, 온도의 변화 등의 원인에 의해 고착현상(galling)이 발생한다. 고착현상이란 성분 혹은 표면경도가 비슷한 금속의 나사산을 조이는 과정에서 발생하는 압력의 증가 및 마찰력에 의해 냉간 용접(cold welding)이 일어나는 것으로 나사산의 표면이 눌어붙게 된다. 이러한 고착현상은 스테인리스 소재에서 많이 발생하는데, 한번 발생한 후에는 비파괴 해소가 불가능한 상태가 되어 경제적 손실을 야기한다. 이러한 고착현상의 해소를 위해 본 연구에서는 주석과 알루미늄을 사용한 새로운 열 확산 코팅 기술을 개발하고 이를 304 스테인리스강에 적용하여 열처리 온도에 따른 특성변화를 확인하였다. 열 확산 코팅을 위해 팩 세멘테이션 방법을 이용하여 아르곤 분위기 하에서 열처리 하였고, 온도는 $200{\sim}250^{\circ}C$에서 코팅을 수행하였다. 이에 따른 코팅 전과 후의 표면 및 단면 분석을 통해 성공적으로 코팅층이 형성됨을 확인하였고, 온도가 증가함에 따라 코팅성분의 양이 증가하는 현상을 보임을 알 수 있었다. 또한, 고착방지성능을 확인하기 위하여 ASTM G196-08 시험을 통해 코팅조건에 따른 고착현상을 분석하였으며, 그 결과 기존에 코팅되지 않은 304 스테인리스강보다 고착현상이 개선됨을 확인하였다. 따라서 304 스테인리스강 소재의 볼트, 너트 제품에 주석-알루미늄 코팅층을 적용시키면 기존의 고착현상을 개선하고 서비스 품질을 향상시킬 수 있을 것으로 판단된다.

• Journal of the Korean Society of Combustion
• /
• v.18 no.3
• /
• pp.68-74
• /
• 2013

가스터빈용 희박 예혼합 연소기 내부에 와류 발생기(vortex generator)를 장착하여 그에 따른 연료/공기혼합 및 NOx 배출 특성 변화를 조사하였다. 이를 위해 수치해석적 방법을 채택하여 연소기내 유동특성, 연료/공기 혼합도, 배기가스(NOx), 화염형상을 분석하였다. 와류 발생기를 장착한 경우, 연소기 내부에서 와류 발생기에 의한 나사산 형상으로 인해 와류가 형성되며 이는 연소기 전면부까지 유지되었다. 또한 연소기 내부 면적 차로 인해 압력섭동이 발생하였다. 이와 더불어 연소기 전면부 기준 상류지역의 연료와 공기의 혼합도가 증가됨으로서 연료 과농지역이 감소하게 되며 이로 인해 전반적인 NOx 발생량의 감소 효과를 볼 수 있었다. 화염 형상의 변화로부터 와류 발생기의 영향으로 선회수는 다소 감소할 것으로 예상되며, 이는 와류 발생기로 인한 유속의 반복적 증감에 의한 결과라고 판단된다.

• Computational Structural Engineering
• /
• v.7 no.3
• /
• pp.133-141
• /
• 1994

When a bolt is tightened up to the range of plastic deformation, yielding may be governed by the combined stresses due to the axial force developed in the bolt and the frictional torque induced on the thread by the contact with the nut. Consideration is taken account of the fact that the unengaged portion of the thread has least sectional area, being subject to initial yielding. Once yielding has taken place some strain hardening effect may result. Incremental stress-strain relations are used to treat the continued yielding, which is equivalent to treat continued yielding as if summing up the effects of thin walled cylinders subject to plastic deformation. M10 bolts of fine threads are used for both computational and experimental purposes. Variation of axial forces and frictional torques vs. the frictional coefficients are presented together with other plots showing some characterist of bolt under plastic deformation. Finally, a design and control aid for the tightening(i.e., kind of nomograph) is presented, showing the relationships among the torque factor and frictional coefficients for that particular bolt used in the experiment.

• The Journal of Korean Academy of Prosthodontics
• /
• v.48 no.3
• /
• pp.224-231
• /
• 2010

Purpose: This study was to investigate how the crestal module design could affect the level of marginal bone stress around dental implant. Materials and methods: A submerged implant of 4.1 mm in diameter and 10 mm in length was selected as baseline model (Dentis Co., Daegu,Korea).A total of 5 experimental implants of different crestal modules were designed (Type I model : with microthread at the cervical 3 mm, Type II model : the same thread pattern as Type I but with a trans-gingival module, Type III model: the same thread pattern as the control model but with a trans-gingival module, Type IV model: one piece system with concave transgingival part, Type V model: equipped with beveled platform). Stress analysis was conducted with the use of axisy mmetric finite element modeling scheme. A force of 100 N was applied at 30 degrees from the implant axis. Results: Stress analysis has shown no stress concentration around the marginal bone for the control model. As compared to the control model, the stress levels of 0.2 mm areas away from the recorded implant were slightly lower in Type I and Type IV models, but higher in Type II, Type III and Type V models. As compared to 15.09 MPa around for the control model, the stress levels were 14.78 MPa, 18.39 MPa, 21.11 MPa, 14.63 MPa, 17.88 MPa in the cases of Type I, II, III, IV and V models. Conclusion: From these results, the conclusion was drawn that the microthread and the concavity with either crestal or trans-gingival modules maybe used in standard size dental implants to reduce marginal bone stress.

• The korean journal of orthodontics
• /
• v.38 no.4
• /
• pp.228-239
• /
• 2008

Objective: The aim of this study was to evaluate the strain induced in the cortical bone surrounding an orthodontic microimplant during insertion. Methods: A 3D finite element method was used to model the insertion of a microimplant (AbsoAnchor SH1312-7, Dentos Co., Daegu, Korea) Into 1 mm thick cortical bone with a pre-drilled hole of 0.9 mm in diameter. A total of 1,800 analysis steps was used to simulate the 10 turns and 5 mm advancement of the microimplant. A series of remesh in the cortical bone was allowed to accommodate the change in the geometry accompanied by the implant insertion. Results: Bone strains of well higher than 4,000 microstrain, the reported upper limit for normal bone remodeling, was observed in the bone along the whole length of the microimplant. At the bone in the vicinity of the screw tip, strains of higher than 100% was recorded. The insertion torque was calculated at approximately 1.2 Ncm which was slightly lower than those measured from the animal experiment using rabbit tibias. Conclusions: The insertion process of a microimplant was successfully simulated using the 3D finite element method which showed that bone strains from a microimplant insertion might have a negative impact on physiological remodeling of bone.

• The korean journal of orthodontics
• /
• v.37 no.2 s.121
• /
• pp.89-97
• /
• 2007

Objective: The purpose of this study was to measure the insertion torque of orthodontic miniscrews regarding changes in their shape, diameter, and length. Methods: Torque values were measured during continuous insertion of the miniscrews into solid rigid polyurethane foam, using a torque tester of driving motor type with a regular speed of 3 rpm. Orthodontic miniscrews (Biomaterials Korea, Seoul, Korea) of cylindrical type and taper type were used. Results: Increasing the length and diameter of the miniscrews increased the maximum insertion torque value in both cylindrical and taper type screws. Insertion torque was increased at the incomplete head of the cylindrical type screw, and at the tapered part of the taper type screw. The insertion torque value of miniscrews was influenced most by diameter, then shape and length. As a result, it was shown that the diameter of the screw had the most influence on insertion torque, and the taper type screw had a higher torque value than the cylindrical type screw. Conclusion: Therefore, a large diameter or taper type screw are adequate for areas of thin cortical bone with a large interdental space, and a small diameter or cylindrical type screw are adequate in the mandibular molar area or the midpalatal area having thick cortical bone.