• Journal of the Korean Chemical Society
• /
• v.60 no.3
• /
• pp.187-193
• /
• 2016

In this study, preparation of positively and negatively charged carbon nanotube (CNT)-collagen (CG) hydrogels with pH sensitive characteristic was reported. The positive and negative characteristics of the prepared hydrogels were created by introduction of positively functionalized CNT-NH₂ and negatively functionalized CNT-COOH, respectively, into the collagen hydrogel. The surface charge of CNTs (CNT-NH₂ and CNT-COOH), CG and CNTs/CG hydrogels was measured by Zetasizer. The swelling ratios of CNT-NH₂/CG and CNT-COOH/CG hydrogels in aqueous solution were checked by measuring of weight changes of the hydrogels in the range of pH 2~10. In detail, the positively charged CNT-NH₂/CG hydrogel swelled up to 5% at pH 4 in comparison to the weight at pH 7, while the negatively charged CNT-COOH/CG hydrogel swelled up to 10% at pH 10. The prepared CNT-NH₂/CG and CNT-COOH/CG hydrogels will be very useful as pH sensitive oral drug-delivering systems for gastrointestine (pH ~2) and small intestine (pH ~9), respectively.

• Journal of the Korean Electrochemical Society
• /
• v.18 no.1
• /
• pp.38-44
• /
• 2015

This review article summarizes the recent progress of quantum dot (QD)-sensitized solar cells based on mesoporous $TiO_2$ thin films. From the intrinsic characteristics of nanoscale inorganic QDs with various compositions, it was possible to construct a variety of 3rd-generation thin film solar cells by solution process. Depending on preparation methods, colloidal QD sensitizers are pre-prepared for later deposition onto the surface of $TiO_2$ or in-situ deposition of QDs from chemical bath is done for direct growth of QD sensitizers over substrates. Recently, colloidal QD sensitizers have shown an overall power conversion efficiency of ~7% by a very precise control of composition while a representative CdS/CdSe from chemical bath deposition have done ~5% with polysulfide electrolytes. In the near future, it is necessary to carry out systematic investigations for developing new hole-conducting materials and controlling interfaces within the cell, thus leading to an enhancement of both open-circuit voltage and fill factor while keeping the current high value of photocurrents from QDs towards more efficient and stable QD-sensitized solar cells.

• Journal of the Microelectronics and Packaging Society
• /
• v.20 no.4
• /
• pp.13-16
• /
• 2013

A lot of various researches have been going on to use heat spreader for LED module. Nano porous aluminum anodic oxide (AAO) applied LED, which is produced from anodization, is easy and economically advantageous. Convensional LED module is consist of aluminum/adhesive/copper circuit. The polymer adhesive in this module is used as heat spreader. However the thermal emission of LED component is degraded because of low heat conductivity of polymer and also reliability of LED component is reduced. Therefore, AAO in this work was applied to heat spreader of LED module which has higher heat conductivity compare to polymer. Bonding strength between AAO and copper circuit was improved with Ti/Cu seed layer by copper sputtering process (DBC) before the bonding. And this copper circuit has been fabricated by electro plating method. Peel strength of AAO and copper circuit in this work showed range between 1.18~1.45 kgf/cm with anodizing process which is very suitable for high power LED application.

• Clean Technology
• /
• v.28 no.4
• /
• pp.301-308
• /
• 2022

Since nanoporous silica aerogel was first synthesized in 1931, its potential as an ultra-lightweight superinsulation material has been steadily attracting attention. Silica aerogel is the best thermal insulation material to date. However, the potential applications of this lightweight material have so far been hindered by its inherent fragibility and brittleness arising from its ultra-porous nature. Although the monolithic form of silica aerogel has the best ultra-lightweight superinsulation properties, it cannot be used in this form. Instead it is used in the form of powders, particles, and blankets. However, these forms still have shortcomings. Silica aerogel is most widely applied in the form of a fiber-reinforced aerogel blanket, but this form is likely to generate dust when handled. Although silica aerogel particles have been proven to be non-toxic to humans, dust formation remains a major barrier to the widespread application of silica aerogel blankets. This paper will investigate the unique properties of silica aerogel and determine what fields it can be used in or potentially be used in due to its unique properties. In addition, we will review the important advances in silica aerogel synthesis technology and its commercialization so far, and then consider the problems that exist for its widespread commercialization in the future and how to overcome them.