• Korean Journal of Materials Research
• /
• 제10권11호
• /
• pp.760-769
• /
• 2000

Mechanical properties of HSLA cast steels alloyed with 0.15% Nb, Ti or V were tested as variations of austenizing temperatures and tempering times. The test results are as follows. The hardness of HSLA cast steels austenized for 2hrs at 115$0^{\circ}C$ was shown the highest value regardless of alloying elements and then decreased as the temperature decreased below 110$0^{\circ}C$. The hardness of HSLA cast steels with 0.15% Ti austenized for 2 hrs at $1150^{\circ}C$ was higher than that of any other HSLA cast steels, and chich was mainly attributed to the relatively high amount of bainite, and solid solution hardening. Charpy impact energy of HSLA cast steels was comparable to the C-Mn cast steel except HSLA cast steels with 0.15% Ti austenized at 115$0^{\circ}C$. The hardness of HSLA cast steels austenized for 2 hrs at $1150^{\circ}C$ increased at a ten-minute tempering, and after that, the hardness kept almost sililar level except HSLA cast steels with 0.15% V.

• Korean Journal of Materials Research
• /
• 제9권12호
• /
• pp.1252-1262
• /
• 1999

The effect of microstructures on the strength-flangeability of Nb bearing hot-rolled high strength steel was investigated in order to improve the strength-flangeability of conventional TS 580MPa grades HSLA steel for the automotive wheel disc. The low temperature coiling method using 3-step controlled cooling pattern after hot rolling was effective to produce the Nb-bearing high strength steel with the polygonal ferrite and bainite duplex microstructures. It was suggested that the suppressed precipitation of grain boundary cementites and the decreased hardness difference between ferrite matrix and bainite cause the excellent stretch-flangeability of ferrite-bainite duplex microstructure steel. Therefore, the formation and propagation of microcracks were suppressed relative to the conventional HSLA steel with ferrite and pearlite microstructure. In addition, the elongation was improved as compared with that of hot-rolled steel sheets using conventional early cooling pattern because the volume fraction of polygonal ferrite was increased.

• Journal of Convergence for Information Technology
• /
• 제11권11호
• /
• pp.143-150
• /
• 2021

It introduces the contents of establishing a geostationary satellite-based forest fire monitoring system that can monitor areas of the Korean Peninsula 24 hours a day for forest fire monitoring, and describes how to establish a forest fire monitoring system and use it in various ways. In order to establish a satellite-utilized forest fire monitoring system, we will describe and draw conclusions on literature research, technical principles, forest fire monitoring means, and satellite forest fire monitoring system. The satellite-utilized forest fire monitoring system can consist of one geostationary satellite equipped with infrared detection optical sensors and a ground processing station that processes data received from satellites to spread surveillance information. Forest fire monitoring satellites are located in the country's geostationary orbit and should be operated 24 hours a day, 365 days a day. Forest fire monitoring technology is an infrared detection technology that can be used in national public interests such as forest fire monitoring and national security. It should be operated 24 hours a day, and to satisfy this, it is efficient to establish a geostationary satellite-based forest fire monitoring satellite system.

• Journal of the Society of Disaster Information
• /
• 제15권2호
• /
• pp.292-300
• /
• 2019

Purpose: To reduce the noise and vibration of reinforced concrete slab structures, the damping performance is to be performed experimentally after installing hollow core or filling it with liquid. Method: Using the hollow rate as an experimental variable, the damping ratio and stiffness of each test specimen at impact load are obtained to determine the difference between the damping ratio and stiffness of the numerical analysis. In addition, the damping effects are reviewed by comparing the difference in the damping ratio and stiffness of a test specimen filled with liquid 50% of the study. Results: Since the difference in resistance between a specimen with or without hollow core is 5%, it is judged that there is no structural problem, and the injection of liquid into the hollow core can increase the damping ratio, which can reduce noise or vibration. Conclusion: At less than 20% of hollow rate, there was little damping effect, and at 30%, damping effect was found. However, if liquid is injected into the hollow core of the specimen, damping rate is shown to increase, and the injection of liquid into the hollow part is believed to reduce noise or vibration.

• Journal of the Society of Disaster Information
• /
• 제14권4호
• /
• pp.466-473
• /
• 2018

Purpose: Nowadays, it is the trend that seismic isolation method and combined method are used for seismic retrofitting, if concrete sphere foundation(CSF) system is applied to mid and low rise RC structure for the seismic isolation, the characteristics of concrete sphere, etc split tensile strength will be need. Method: The various experiments are carried out to know the split strength of high strength concrete sphere(60Mpa) and the ratio of split strength of concrete sphere to standard cylinder specimen, the size effect of concrete sphere with diameter. Results: It was purposed that the split strength of concrete sphere with diameter 150mm will be lower than that of cylinder specimen but, the average value is 4.39 Mpa and the ratio is higher than that of cylinder specimens, each 3.8% and 13.7%, the reason of this result is thought that the internal stress action of spot load and line load are different. Conclusion: There is a standard method for split tensile strength of cylinder type specimen, but there are few studies for the tensile split of concrete sphere. And therefore, in this study, theoretical and experimental details of concrete sphere will be served for the concrete sphere foundation or other sequent studies.

• Journal of Aquaculture
• /
• 제6권1호
• /
• pp.13-27
• /
• 1993

In order to determine the protein requirements of the Korean rockfish Sebastes schlegeli six isocaloric diets containing crude protein level from 20\%\;to\;60\%$ were fed to two groups of fish, small and large size, with the initial average body weight of 8 g and 220 g respectively. White fish meal was used as a sole protein source. Daily weight gain, daily protein retention. daily energy retention, feed efficiency, protein retention efficiency and energy retention efficiency were significantly affected by the dietary protein content (p< 0.05). The growth parameters (that is, daily weight gain, daily protein retention and daily energy retention) increased up to $44\%$ protein level with no additional response above this point. The protein requirements were determined from daily weight gain using two different mathematical models. Second order polynomial regression analysis showed that maximum daily weight gain occurred at $56.7\%\;and\;50.6\%$ protein levels for the small size group and the large size group, respectively. However the protein requirements, determined by the broken line model, appeared to be about $40\%$ for both groups. Nutrient utilization also suggested that the protein requirements of both groups were close to $40\%$. When daily protein intake was considered, daily protein requirements per 100g of fish, estimated by the broken line model, were 0.99g and 0.35g for the small and large size groups respectively. Based on these results, a $40\%$ dietary crude protein level could be recommended for the optimum growth and efficient nutrient utilization of the Korean rockfish weighing between 8g and 300g.

• Journal of Aquaculture
• /
• 제6권1호
• /
• pp.29-46
• /
• 1993

In order to determine the optimum digestible energy to protein (DE/P) ratio in diets for Korean rockfish, Sebastes schlegeli, $45\%$ and $40\%$ protein diets with graded levels of DE/P ratio were fed to average 36g and 80g fish, respectively. The DE/P ratios in the $45\%$ protein diets ranged from 7.4 to 10.0 kcal/g protein, while those in the $40\%$ protein diets varied between 7.5 and 8.9 kcal/g protein. Both in the $45\%$ and $40\%$ protein diets, the changes in the DE/P ratios did not affect either the daily weight gain or the feed efficiency. However daily protein retention, daily energy retention, nutrient utilization and chemical composition in carcass varied depending on the DE/P ratios. Thus based on these parameters as criteria, the optimum DE/P ratio for both the $40\%$ and $45\%$ protein diets, estimated to be about 8 kcal/g protein. DE/P ratios more than 8 kcal/g protein, led to the deposition of a large amount of body fat, especially in the viscera. Any protein-sparing effect was not observed with the increase of the energy content in the diets. Apparent digestibility coefficients determined by the indirect method, using $Cr_2O_3$ as an indicator, were around $90,\;98\%\;and\;70\%$, for protein, lipid and digestible carbohydrate respectively, without any distinct differences between the diets.

• Journal of Aquaculture
• /
• 제1권1호
• /
• pp.67-73
• /
• 1988

A growth experiment of tilapia (offsprings of the hybrid between Oreochromis niloticus and O. mossambicus) under different dissolved oxygen levels in the recirculating water system was conducted at the Fish Culture Experiment Station of the National Fisheries University of Pusan from February 4 to March 5, 1986. Six tanks with a capacity of $1.8m^3$ of water each were used under the same condition of water parameters except for dissolved oxygen levels which were designated to maintain at 1.5, 2.0, 2.5, 3.0, 3.5 and 4.0 mg/$\iota$. Each tank was stocked with 90 kg of fish each averaging 64 to 69 grams. The average water temperature during the course of the experiment was $22.5^{\circ}C$. The results obtained are summarized as follows: The food conversion efficiencies were very good, being 1.05-1.11 at 3.5, 3.0, 2.5 and 2.0 mg/$\iota$ DO levels without any significant differences among them, but at 4.0 mg/$\iota$ the F. C. was 1.39 and at 1.5 mg/$\iota$ it was 1.61 being very poor compared with the others. The daily growth rate performance was best at 3.5 mg/$\iota$ dissolved oxygen level followed by 3.0 and 2.5 mg/$\iota$ with slight differences while at 4.0 and 2.0 mg/$\iota$ DO levels the growths were significantly poor, and at 1.5 mg/$\iota$ DO level it was extremely poor. In 1.5 mg/$\iota$ group, the fish did not accept feed vigorously and after feeding the fish usually concentrated around the inflow point showing oxygen deficiency response. While at 4.0 mg/$\iota$ high feeding rates tended to waste significant amounts of feed while eating and led to water deterioration, and above these levels the results is considered to lead to a waste of energy with uneconomical performance. On the other hand, at and below 2.0 mg/$\iota$ DO level the tilapia certainly showed a poor growth performance. The experiment indicates that the DO range of 2.5$\~$3.5 mg/$\iota$ is the optimum level for the good growth performance.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• 제10권4호
• /
• pp.267-273
• /
• 1977

Rainbow trout were reared in a small indoor aquarium which was equipped with a simple recirculating biofilter combined with a small amount of inflowing water for 199 days from April 25 to November 10, 1977 in Busan where very hot summer air temperature is encountered, and results obtained were promissing as following; 1. The aquarium has dimensions of $1m\;\times\;1m\;\times\;67cm(depth)$, and a bottom center sedimentation chamber of conical type through which out-flowing water is pushing fecal matter and other detritus outward. The conical sedimentation chamber measures 20 cm depth and 20 cm diameter at its upper mouth and tapers to the bottom end which is connected to 4 cm diameter draining pipe. The draining pipe goes through under the tank and then is elevated on the side. The water depth was maintained at about 40 cm depth by adjusting the heigh of draining pipe. The filter bed contained 16 l of $3\~5\;mm$ zeolite gravels, and water circulation rate was about 1030 l/hr. 2. Continuous inflowing water resulted in a good elimination of waste materials through its outflowing water thus reducing waste loading in the filter. 3. Mean temperature of water in the rearing aquarium containing about 400 l water volume was maintained at around 20 to $22^{\circ}C$ by 0.59 l/min of the inflowing well water which usually maintained the temperature of $17^{\circ}C$ during the hot summer season from the first of July to the first of October when the 10-days-mean air temperature ranged from $20^{\circ}\;to\;27.3^{\circ}C$ $(total\;mean\;24.6^{\circ}C) $ and under this condition the fish continued normal growth. 4. The production per 1 l/min of inflowing water with this simple biofilteration reached 30 hg. 5. The total cost including all feed and power during this experimental rearing period fell well within the economic establishment and if the feed and filteration system are improved the benefit-cost ratio will be much increased.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• 제11권4호
• /
• pp.233-238
• /
• 1978

Rainbow trout were reared in a stainless steel aquarium from Nov. 11, 1977 to June 12, 1978, and the following results were obtained : 1. The volume of water was about $400\iota$ in a aquarium measuring $1m\;(Length)\times1m\;(Width)\times67cm(Height)$ and water depth 40 cm. Water was supplied for about 16 hours daily at a rate $3\iota/min$ and was drained through the conical settling part in the middle of the aquarium bottom. Filter tank was about $23cm(W)\times23cm(L)\times40cm(D)$ and contained pebbles 30 cm in depth. Water recirculation rate was at)out $1,030\iota/hr$, or 2.6 turn-over per hour. 2. During the first period (77 days), the trout grew from 88.3g to 229g in average, the total weight attaining 30.7kg. The food coefficient was 1.249, average daily increment 243.3g, average daily growth rate 1.245%, and the mortality was 2 smallest fish weighing 53 g, owing to unknown reason. During the second period (135 days), the trout grew from 239g to 555g in average, the total weight attaining 57.2 kg. The food coefficient was 1.447, average daily increment 279.8g, average daily growth rate $0.65\%$ and the mortality was 31 fish weighing 11,255 g, owing partly to miss-handling and partly to disease. 3. The feed consisting of fully domestic materials was prepared in this laboratory, and the feed conversion was not inferior to high protein commercial feed available in foreign countries. 4. The result of whole period for 212 days was 56.5 kg in gross increment, and based on this result, when $1\iota/min$ full day inflowing water available, the net production will become 28.25 kg. So, if a 5000kg production is planned, $180\iota/min$ or about $10.8m^3/hr$ be reauired, and the production in value frill become 15million won at local price at the expense of about 5.3 million won. From the result of this experiment, rainbow trout is feasible for commercial production in Korea with relatively small amount of well water and simplified water recirculation system.