• Korean Journal of Materials Research
• /
• v.18 no.5
• /
• pp.266-271
• /
• 2008

Magnesium alloys are alloyed with rare earth elements (Re, Ca, Sr) due to the limited use of magnesium in high-temperature conditions. In this study, the influences of Zr and Zn on the aging behavior of a Mg-Nd-Y alloy were investigated. magnesium alloys containing R.E elements require aging treatments Specifically, Nd, Y and Zr are commonly used for high-temperature magnesium alloys. Various aging treatments were conducted at temperatures of 200, 250 and $300^{\circ}C$ for 0.5, 1, 3, 6, and 10 hours in order to examine the microstructural changes and mechanical properties at a high temperature ($150^{\circ}C$). Hardness and high-temperature ($150^{\circ}C$) tensile tests were carried out under various aging conditions in order to investigate the effects of an aging treatment on the mechanical properties of a Mg-3.05Nd-2.06Y-1.13Zr-0.34Zn alloy. The maximum hardness was 67Hv; this was achieved after aging at $250^{\circ}C$ for 3 hours. The maximum tensile, yield strength and elongation at $150^{\circ}C$ were 237MPa, 145MPa and 13.6%, respectively, at $250^{\circ}C$ for 3 hours. The strengths of the Mg-3.05Nd-2.06Y-1.13Zr-0.34Zn alloy increased as the aging time increased to 3 hours at $250^{\circ}C$ This is attributed to the precipitation of a Nd-rich phase, a Zr-rich phase and $Mg_3Y_2Zn_3$.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.3 no.1
• /
• pp.19-26
• /
• 1970

During the summer of 1969, a series of experiments on the spawning and development of the eggs of grass carp and silver carp was performed with the following results, but the complete development of eggs Iras not accomplished: 1. The season of maturity for both species is estimated to be from the end of June to the beginning of August. 2. Pituitary glands for the use of inducing maturation should be obtained before the maturation season of its donor. 3. Silver carp as small as 40 cm in body length (48 cm in total length) with an age of 6 years were found to have reached maturity, and the number of eggs in the ovaries were from about 23 to 26 thousand for those with body lengths of 40-44.5 cm. 4. The conical-shaped net cloth incubator worked better than others, and each incubator was most effective when installed in parallel series to the water supply pipe with a valve for each incubator to control water flow. 5. During the egg development, if any cell or cells were displaced, the eggs eventually died. 6. The proper manipulation of brood fish before the egg-taking seems to be very Important, and close care should be paid to feeding them well and keeping them in a pond of proper water depth.

• Journal of The Korea Institute of Healthcare Architecture
• /
• v.22 no.4
• /
• pp.29-36
• /
• 2016

Purpose: Considering the proportion of the population such as the elderly, pregnant women, infants companion and constantly increasing foreign tourists, there is a high need for implementing an environment without barriers. In terms of policy and institutional aspects, Jeju Special Self-Governing Province is striving to create an environment without barriers and to promote the safety and convenience of Vulnerable Pedestrians. But it is not enough to create a viable barrier-free environment. Methods: Method of this research is to analyze the general population status and installed facilities status for the disabled in Jeju. And analysis of policy research needs and level of barrier-free. By applying the barrier-free environment certification standards should conduct an assessment of the level of the current public office buildings in Jeju. It presents the environmental improvement of public office buildings for barrier-free environment. Result: Barrier-free environment status of the five public office buildings research surveyed all buildings have shown low levels of installed facilities for the disabled. In particular, it was analyzed that represents a very low level in the intermediate facilities and other facilities. The development of a specific installation manual for the facilities for the disabled is required to improve public office buildings. And barrier-free criteria need to reflect on the implementation of regulations. Implications: Through continuous research to analyze the barrier-free level and problems of public office buildings, it will be made to improve the comprehensive and reasonable alternative.

• Journal of The Korea Institute of Healthcare Architecture
• /
• v.23 no.4
• /
• pp.7-15
• /
• 2017

Purpose: The Korean government has implemented a Barrier Free Certification System since 2008 to create a secure and convenient environment for the socially disadvantaged. The drastic increase in the number of BF-certification facilities is expected due to the revision of the system and increasing the number of certification institutions. An analysis of individual evaluation items needs to be made for the BF-Certification with public confidence. Method: Korean standard, International Standard(ISO/FDIS 21542, 2011), German Standard(DIN 18040-1, 2010), Austrian Standard(${\ddot{O}}NORM$ B 1600, 2017) and Swiss Standard(Norm SIA 500 / SN 521 500, 2009) were investigated and analyzed. A comprehensive improvement plan is proposed by comparing details of the aforementioned standards and the evaluation items of BF-Certification. Results: Many problems arise in applying existing Barrier-free standards due to changes in population structure, environmental change and the use of powered wheelchairs. International standards are being improved to solve these problems. The korean standards also require improving of the Barrier Free Law and Certification System, which reflect these trends. In korean cases, standards such as the size of the doors (width and height), the Unobstructed Manoeuvring Space and Clear Space at the Latch side of the Door are required to improve standards in accordance with international standards. In addition, the expression of laws and evaluation items of BF-Certification should be clearly defined. And the application of visual contrast standards for the enhancement of perceptions presented in international standards should be considered. Implication: Barrier Free related legal standards and evaluation items of BF-Certification that are used in Korea are required to be revised in consideration of social and environmental changes. Comprehensive improvements should be made through detailed review.

• Korean Journal of Materials Research
• /
• v.8 no.4
• /
• pp.354-358
• /
• 1998

Effect of cold drawing ratio and aging time on the hardness of lnconel 718 wire aged at 11l6K were investi¬gated by hardness measurement and scanning & transmission electron microscopy. Hardness which was 245Hv in as¬solution treated condition increased very rapidly to 450Hv as cold drawing ratio increased to 50%. The hardness in the early stage of aging was increased by the precipitation of $\gamma^{'}$ and $\gamma^{'}$ phases and after the peak hardness, the hardness was decreased by the transformation of $\gamma^{'}$ phase to $\delta$ phase. The time to reach peak hardness during aging appeared to be reduced with the increase of cold drawing ratio, and those times were 30, 10, and 5 minutes for 0, 30 and 50% cold drawn materials, respectively. For the 50% cold drawn material. $\gamma^{'}$ and $\gamma^{'}$ were precipitated by aging for 5 minutes at 1116K. The hardness in the same material was largely decreased under the initial hardness by the recrystallization.

• Korean Journal of Metals and Materials
• /
• v.50 no.2
• /
• pp.136-145
• /
• 2012

Resistance spot welding of TRIP780 steels was investigated to enhance understanding of weld fracture mode after tensile shear testing (TST) and L-shape tensile testing (LTT). The main failure mode for spot welds of TRIP780 steels was partial interfacial fracture (PIF). Although PIF does not satisfy the minimum button diameter (4${\surd}$t) for acceptable welds, it shows enough load carrying capacity of resistance spot welds for advanced high strength steels. In the analysis of displacement controlled L-shape tensile test results, cracks initiated at the notch of the faying surface and propagated through the interface of weldments, and finally, cracks change path into the sheet thickness direction. Use of the ductility ratio and CE analysis suggested that the occurrence of PIF is closely related to high hardness and brittle welds, which are caused by fast cooling rates and high chemical compositions of TRIP steels. Analysis of the hold time and weld time in a welding schedule demonstrated that careful control of the cooling rate and the size of a weld nugget and the HAZ zone can reduce the occurrence of PIF, which leads to sound welds with button fractures (BFs).

• Korean Journal of Metals and Materials
• /
• v.49 no.12
• /
• pp.967-976
• /
• 2011

Conventional fracture tests of resistance spot welds have been performed without consideration of the paint baking process in the automobile manufacturing line. The aim of this paper is to investigate the effect of the paint baking process on load carrying capacity and fracture mode for resistance spot welded 590 dual phase (DP), 780DP, 980DP, 590 transformation in duced plasticity (TRIP), 780TRIP and 1180 complex phase (CP) steels. With paint baking after resistance spot welding, the l-shape tensile test (LTT) and nano-indentation test were conducted on the as-welded and paint baked samples. Paint baking increased the load-carrying capacity of the resistance spot welded samples and improved the fracture appearance from partial interfacial fracture (PIF) to button fracture (BF). Improvement in fracture appearance after LTT is observed on weldments of 780 MPa grade TRIP steels, especially in the low welding current range with paint baking conditions. The higher carbon contents (or carbon equivalent) are attributed to the low weldability of the resistance spot welding of high strength steels. Improvement of the fracture mode and load carrying ability has been achieved with ferrite hardening and carbide formation during the paint baking process. The average nano-indentation hardness profile for each weld zone shows hardening of the base metal and softening of the heat affected zone (HAZ) and the weld metal, which proves that microstructural changes occur during low temperature heat treatment.

• Korean Journal of Metals and Materials
• /
• v.46 no.10
• /
• pp.609-616
• /
• 2008

Conventional bake-hardenable(BH) steels should be annealed at higher temperatures because of the addition of Ti or/and Nb which forms carbides and raises recrystallization start temperature. In this study, the development of new BH steels without Ti or Nb addition has been reviewed. The new BH steels have nearly same mechanical properties as the conventional BH steels even though it is annealed at lower temperature. The steels also show smaller deviation of the mechanical properties than that of the conventional BH steels because of the conarol of solute carbon content during steel making processes. The deviation of mechanical properties in conventional BH steels is directly dependent on the deviation of solute carbon which is greatly influenced by the amount of the carbide formers in conventional BH steels. Less alloy addition in the newly developed BH steels gives economical benefits. By taking the advantage of sulfur and/or nitrogen which scarenge in Interstitial-Free or conventional BH steels, fine manganese sulfides or nano size copper sulfides were designed to precipitate, and result in refined ferrite grains. Aluminum nitrides used as a precipitation hardening element in the developed steels were also and resull in fine and well dispersed. As a result, the developed steels with less production cost and reduced deviation of mechanical properties are under commercial production. Note that the developed BH steels are registered as a brand name of MAFE(R) and/or MAF-E(R).

• Korean Journal of Materials Research
• /
• v.7 no.2
• /
• pp.129-135
• /
• 1997

This study has investigated the effects of aging treatment on thc nlechanical propcrries of blg-iiAl-x%nix - 0.1.2) alloys fabricated by the squeeze castmg process. The microstructurcs of as-squeeze cast were composed of pro eurectic $\alpha$ magnesium solid solution, super saturated $\alpha$ solid solution and $\beta(Mg_{17}AI_{12}$) compund. Agcd at both $200^{\circ}C$ and $240^{\circ}C$, Mg--6AixZn alloys showed the peak hardness due to the formation of $\beta(Mg_{17}AI_{12}$) precipitates. The tiiscontinuous precipitates of the lamella r\.pe are predominant at $200^{\circ}C$ aging tredrment. tvhilc. the finely dispersed continu ous precipitates were major type at $240^{\circ}C$ treatment. Mg-- GAI-xZn a1loi.s fabricated hy the squeeze casting process had the hetter combination of tensile strength and elongation compared to the conventionally cast alloys. As increascci zinc: contents. the tensile strength was increased 11y the soiid solutirin strengthening effect of zinc,.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.15 no.1
• /
• pp.47-51
• /
• 1982

Red tilapia fingerlings were tested for 45 days on the growth rate in a closed recirculating water system omitting filter bed and was compared with common carp fingerlings grown together in the same tank and also with red tilapia fingerlings grown in a well conditioned conventional pond. The tank water was kept in deepgreen colour by heavy phytoplankton bloom during the most of the experimental period and duckweeds, Lemna sp. and water hyacinth, Eichhornia crassipes were put to grow in the parts of the water system. Total ammonia level in the tank was mostly kept at about 5 to 7 ppm, with a fluctuation between 3.4 and 11.2 ppm. Average daily growth rate of the tilapia in the experimental tank was $6.5112\%$ without any mortality, compared to $3.617\%$ for common carp fingerlings involving some mortality in the same tank, and to $5.7712\%$ for the tilapia grown in the conventional pond. The feed used for the experiment was one prepared for the rearing of common carp, and the duckweed grown in parts of the water system was routinely collected and fed to the tilapia in the tank as supplementary diet probably satisfying unknown growth factors.