• Proceedings of the KWS Conference
• /
• 2009.11a
• /
• pp.26-26
• /
• 2009

TIG 용접은 고품질이고 용접인자의 제어가 쉽고 정확하다는 장점이 있지만, 얕은 용입과 낮은 생산성과 같은 단점이 있다. TIG 오비탈 용접에서는 용입의 한계 때문에 작은 루트면과 넓은 그루브를 가공하여 다층 용접을 하며, 루트패스에서는 파이프 진원도에 의한 핏업 시 단차의 문제가 자주 발생하여 많은 현장에서 루트갭을 만들어 수동 용접하는 실정이다. 따라서 생산성이 낮으며 생산 단가가 높고 용접 품질이 작업자에 따라 다르게 된다. 이러한 문제점을 해결하여 자동 오비탈 용접을 위해 단차를 흡수 할 수 있는 용접 공정 개발이 필요하다. 본 연구의 목적은 TIG 용접에서 단차에 따른 용접성을 검토하여 이를 맞대기 용접에 적용했을 때 균일한 이면비드를 얻는 공정을 개발하는 것이다. 따라서 본 연구는 아래보기 자세에서 단차에 따른 용입 특성을 이면비드 및 단면으로 비교 분석하였다. 단차 없이 아크길이만 1mm, 2mm, 3mm로 변경하여 실험한 결과 아크길이가 짧아질수록 표면비드 폭은 좁아졌고 이면비드 폭은 증가하는 경향을 나타내어 아크길이가 짧아질수록 용융효율이 증가하는 것을 확인하였다. 단차 1mm에서 아크길이 3mm를 제외하고 표면비드 및 이면비드가 미려하였다. 하지만 단차 2mm에서는 아크길이 1mm, 2mm, 3mm 전부 이면비드가 생성되지 않았다. 이는 단차로 인해 아크길이가 증가하여 용융효율이 낮아졌기 때문이라 판단된다. 이면비드가 생성되지 못한 시험편을 백 베벨링(0.5mm, 1.0mm, 1.5mm, 2.0mm)하여 실험한 결과 단차 2mm, 아크길이 1-3mm 백 베벨링 2.0mm 적용한 시험편에서 양호한 이면비드를 얻을 수 있었다.

• Journal of the Korea Convergence Society
• /
• v.9 no.9
• /
• pp.263-270
• /
• 2018

The purpose of this study is to investigate the correlation between the demographic characteristics of Korean men and the preference of women's grading such as age, education, marital status, occupation, monthly income, and residence. After the questionnaire distribution, 333 questionnaires were analyzed statistically. Through this study, we will investigate the preference of men according to the step length of women's graduation cuts, and contribute to the establishment of the most preferred type of graduation cuts. As a result of the questionnaire analysis, 51.1% of all males preferred the gradation type with a large step of the cut length, and it was found that there was a difference in the preference for the step according to demographic characteristics (p <0.05) It is possible to conduct various studies on the style of the graduation cut among the hairstyles of women who are visually preferred and beautiful. In addition, it will be possible to derive the importance of customer satisfaction in hair salons, and it will be a basic index for searching for changes in the gradation cuts that can be applied in various ways while maximizing the aesthetic image of women.

• Journal of Welding and Joining
• /
• v.22 no.4
• /
• pp.1-3
• /
• 2004

용접변형은 용접잔류응력과 같이 고유변형도에 의해 발생되며, 고유변형도의 분포형상에 따라 그림 1과 같은 용접변형이 발생된다. 이러한 용접변형은 강구조물 제작시 다양한 용접부형상에 의해 복합적으로 발생되며, 이것은 강구조물을 설계치수를 변화시키거나 부재 간 단차를 발생시켜 절단 또는 교정과 같은 생산공정에 불필요한 작업을 유발시켜 생산성을 저하시킨다.(중략)

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.25 no.6
• /
• pp.262-269
• /
• 2021

This paper conducts an evaluation of the structural performance of the lap splice detail of SD700 headed bar experiment for developing an RC beam with different depths joint details. The experiment variable is lap splice length, yield strength, and end anchorage of main reinforcements. For all specimens, a headed bar was applied to the main reinforcement of the beam with low depth (B2), and the beam with high depth (B1) was applied to the main reinforcement with two splice methods: straight headed bar and 90° hooked-headed bar. The experimental results were that specimens of applying SD500 and SD600 had the results of flexural fracture at the lap splice location, which maximum load was similar. For specimens of appling SD500, the 90° hooked-headed bar of B1, suppressed horizontal cracks in the lap splice section compared to the straight headed bar. Specimens of applying an SD 700 headed bar had the results of brittle anchorage failure. In addition, maximum load was increased with the lap splice length increasing. For specimens of applying SD700 headed bar, test for test maximum load/theoretical load for test development length/design development length were estimated to be 1.30~1.48 for the ACI 318-19 equation, and 1.14~1.30 for the KDS-2021 equation. Thus, ACI 318-19 equation had conservatively greater safety factors as estimated development lengththened.

• Journal of Digital Convergence
• /
• v.16 no.10
• /
• pp.479-484
• /
• 2018

This study is an attempt to analyze the changes and morphological analysis of the one length hair style of women in the Imperial Japanese colonial period, and the purpose of this study is to analyze the components of hair design such as shape, texture, and color based on the precedent and the book and to make possible various styles of one length hair style cut. From the results of this study, one length hair style showed the outline shape with no step height of cut length, natural hair texture and natural hair color in 1910s to 1920s. In the 1930s, the one length hair style showed a slight cut length step height and a slight discoloration using a diamond shape, a narrow wave of natural texture, hydrogen peroxide or oxygenated water. In the 1940s, one length hair style did not find any singularity to pursue brilliant beauty(美) in terms of form, texture, and color. This study may enable a deep and detailed follow up study on one length hair style, and will be a cornerstone for the development of basic data of hair beauty education and trend of new mode.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.20 no.4
• /
• pp.144-152
• /
• 2016

This paper focuses on the experimental study for investigating the performance for lap splice of hooked or headed reinforcement in beam with different depths. In the experiment, seven specimens, with its variables as the lap length of headed or hooked bar, the existence of stirrups, etc., was manufactured. Bending test was conducted. Lap strengths by test were compared with the theoretical model based on KCI2012. The result showed that the cracks at failure mode occurred along the axial direction to a headed bar. The initial stiffness and the stiffness after initial crack were similar for all specimens. For HS series specimens without stirrups, a 25% increase in lap length was increased 11.8~18.1% maximum strengths. For HH series specimens without stirrups, a increase in lap length did not affect the maximum strengths because of the pryout failure of headed bar. For HS series specimens, the theoretical lap strengths based on KCI2012 considering the B grade lap and the reduction factor for stirrup were evaluated. They are smaller than the test strengths and can ensure the safety in terms of strength capacity. For HH series specimens, the stirrups in the lap zone are needed to prevent the pryout behaviour of headed bar.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2009.05a
• /
• pp.1884-1888
• /
• 2009

군산복합화력발전소의 냉각수 취수부는 부지 여건상 수로의 길이가 짧고, 좌안이 좁아진 후 단차가 있는 형태에 직각으로 흐름방향이 전환되면서 CWP로 유입되는 구조로 설계되었기 때문에 CWP 운영에 불리한 수리현상이 예상되어 수치모의와 수리모형실험을 통한 사전검증이 필요하였다. 이에 $FLOW-3D^(R)$를 이용한 3차원 수치모의와 축척 1/10의 수리모형실험을 통하여 면밀히 검토한 결과 CWP 진입부의 깊은 수심이 흐름을 감세하여 0.3m/s 이하의 유속분포를 나타내 균등취수에 문제가 없는 것으로 확인되었다.

• Tribology and Lubricants
• /
• v.31 no.4
• /
• pp.170-176
• /
• 2015

As a continuation of Part I, which developed a design formula of the minimum corner radius (R_min) for restraining tribological failures, Part II investigates design parameters such as material properties and contact force. As design examples, Al 7075-T651, SST 304 and HT-9 are chosen for the materials and 1, 10 and 100 kN are used for the forces. The results show that the difference in R_min decreases as either the elastic modulus increases or the contact force decreases. Given the same material and force, the permissible R_min decreases as the flat region increases and vice versa. Because the R_min values obtained from the examples are very small, the dimensions of the corner radius normally designed in engineering structures are regarded acceptable. The von Mises stress evaluated for a typical example, which is far below the yield strength, confirms this interpretation. Nevertheless, the present work can provide a design criterion as well as a guideline for quality control in the manufacturing of, in particular, contact corners, which has not been attempted before to the best of the author’s knowledge. In addition, this paper considers the problem of a step that may be formed in the contact contour by using a similar approach. The result shows that no size of the step is permissible.

• Proceedings of the Korea Contents Association Conference
• /
• 2008.05a
• /
• pp.792-795
• /
• 2008

AGT system is a kind of light railway train. AGT system use of concrete track and rubber tire, so it can be reduce the noise and vibration, compare to the normal train system. And, the dynamic responses of normal bridge are influenced by the dynamic characteristics of bridge, the speed of vehicle and the surface roughness of railway. But the AGT system bridge is influenced not only the above facts but also the guiderail unevenness, because, AGT vehicle steered by guiderail. So, in this study, optimized service condition is suggested for the design and operation of AGT system, by the means of experimental study. The experiments are executed for PSC bridge with length of 30m, at the AGT test line in Kyongsan. The test results are compared and investigated according to the prominence. In the test result, the guiderail prominence influenced on the dynamic response of bridge. It shows a increase as compared with no guiderail prominence in the dynamic response value acceleration, displacement, stain.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.11
• /
• pp.481-487
• /
• 2018

This paper proposes a method to detect and monitor the land creeping area using a UAV to analyze the damaged area efficiently. Using a UAV, it was possible to secure the safety of the investigators before the field survey and effectively utilize it to establish an investigation plan because an orthophoto can be used to detect and scale the cracks in a land creeping area. In addition, it was possible to analyze the scale of the crack quantitatively by extracting the topographic information from the orthophoto. The study sites were found to have a total crack area of 1.01 ha, a length of 1.07 km, an average width of 10 m, and a step distance of 1 to 10 m. Periodic UAV measurements can be used to detect displacements on the land creeping area and monitor the direction and scale of crack spread. Therefore, it is expected to be used effectively during recovery planning. Applying the UAV to the land creeping area resulted in the qualitative and quantitative results quickly and easily in dangerous mountainous watersheds. Therefore, it is expected that it will contribute to the development of related industries because of the high availability of a UAV in forest soil sediment disasters, such as landslides, debris flow, and land creeping area.