• Membrane Journal
• /
• v.24 no.3
• /
• pp.223-230
• /
• 2014

A numerical analysis was performed for concentration of methane from the biogas using a polysulfone hollow fiber membrane permeator. Governing equations were derived for the countercurrent flow and numerically solved by using the Compaq Visual Fortran 6.6 software. When the methane mole fraction of feed was 0.5, the mole fraction of retentate increased from 0.5 to 0.8; the normalized retentate flow rate to the feed flow rate decreased from 1.0 to 0.57 at the given typical operating condition as the feed gas flowed from the inlet to the outlet of the membrane. As the methane mole fraction of feed was changed to 0.9, the methane mole fraction of retentate became 0.93 and the normalized retentate flow rate was changed to 0.91. When the pressure ratio of the permeate to the feed was varied from 0.33 to 0.17, there was a little difference in the methane mole fraction of retentate for the low stage cut of 0.1, whereas there was an significant increment for the high stage cut of 0.3. The retentate methane mole fraction remained relatively high despite the change of a stage cut as the area of the membrane increased from $1.14m^2$ to $2.57m^2$.

• Membrane Journal
• /
• v.28 no.4
• /
• pp.221-232
• /
• 2018

The silica containing carbon ($C-SiO_2$) membranes were fabricated using poly(imide siloxane)(Si-PI) and polyvinylpyrrolidone (PVP) blended polymer. The characteristics of porous carbon structures prepared by the pyrolysis of polymer blends were related with the micro-phase separation behaviors of the two polymers. The glass transition temperatures ($T_g$) of the mixed polymer blends of Si-PI and PVP were observed with a single $T_g$ using differential scanning calorimetry. Furthermore, the nitrogen adsorption isotherms of the $C-SiO_2$ membranes were investigated to define the characteristics of porous carbon structures. The $C-SiO_2$ membranes derived from Si-PI/PVP showed the type IV isotherm and possessed the hysteresis loop, which was associated with the mesoporous carbon structures. For the molecular sieving probe, the $C-SiO_2$ membranes were prepared with the ratio of Si-PI/PVP and the pyrolysis conditions, such as the pyrolysis temperature and the isothermal times. Consequently, the $C-SiO_2$ membranes prepared by the pyrolysis of Si-PI/PVP at $550^{\circ}C$ with the isothermal time of 120 min showed the $O_2$ permeability of 820 Barrer ($1{\times}10^{-10}cm^3(STP)cm/cm^2{\cdot}s{\cdot}cmHg$) and $O_2/N_2$ selectivity of 14.

• Korean Chemical Engineering Research
• /
• v.45 no.5
• /
• pp.506-514
• /
• 2007

To select the best oxygen carrier particle for syngas fueled chemical-looping combustor, the reduction reactivity and carbon deposition characteristics were determined in a thermogravimetric analyzer. Four kinds of oxygen carrier particles (NiO/bentonite, $NiO/LaAl_{11}O_{18}$, $Co_xO_y/CoAl_2O_4$, $NiO/NiAl_2O_4$) were tested with the simulated syngas (30% $H_2$, 10% $CO_2$, 60% CO) as a reduction gas. With each of these particles, the maximum conversion and oxygen transfer capacity increase with increasing the reduction temperature At the given experimental range, the optimum operating temperature to maximize oxygen transfer rate is found to be $900^{\circ}C$ and carbon deposition on the particles could avoid at the temperature above $800^{\circ}C$. Among four kinds of oxygen carrier particles, the NiO-based particles exhibits better reactivity than the CoO-based particle. Moreover, the NiO/bentonite particle produces the best reactivity based on the oxygen transfer rate and the degree of carbon deposition. The measured oxygen transfer rate increases as the metal oxide content in NiO/bentonite particle is increased thereby higher metal oxide contents could provide stable operation of chemical-looping combustor.

• Korean Chemical Engineering Research
• /
• v.47 no.3
• /
• pp.362-367
• /
• 2009

Recently, the use of formic acid as a fuel for direct liquid fuel cells has emerged as a promising alternative to methanol. In the work presented herein, we evaluated direct formic acid fuel cells(DFAFCs) with various components under operating conditions, for example, the thickness of the proton exchange membrane, concentration of formic acid, gas diffusion layer, and commercial catalyst. The thickness of the proton exchange membrane influenced performance related to the fuel cross-over. To optimize the cell performance, we investigated on the proper concentration of formic acid and catalyst for the formic acid oxidation. Consequently, membrance-electrode assembly(MEA) consisted of $Nafion^{(R)}$-115 and the Pt-Ru black as a anode catalyst showed the maximum performance. This performance was superior to the DMFCs' one.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.9
• /
• pp.536-542
• /
• 2018

Tin dioxide, $SnO_2$, is a well-known n-type semiconductor that shows change in resistance in the presence of gas molecules, such as $H_2$, CO, and $CO_2$. Considerable research has been done on $SnO_2$ semiconductors for gas sensor applications due to their noble property. The nanomaterials exhibit a high surface to volume ratio, which means it has an advantage in the sensing of gas molecules. In this study, SnO nanoplatelets were grown densely on Si substrates using a thermal CVD process. The SnO nanostructures grown by the vapor transport method were post annealed to a $SnO_2$ phase by thermal CVD in an oxygen atmosphere at $830^{\circ}C$ and $1030^{\circ}C$. The pressure of the furnace chamber was maintained at 4.2 Torr. The crystallographic properties of the post-annealed SnO nanostructures were investigated by Raman spectroscopy and XRD. The change in morphology was confirmed by scanning electron microscopy. As a result, the SnO nanostructures were transformed to a $SnO_2$ phase by a post-annealing process.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.4
• /
• pp.588-595
• /
• 2020

This study examined the catalytic property of Ni-catalyst used in the gas purifying process to manufacture inert gases of N2 and Ar with high-purity over 9N for semiconductor industrial applications. Two types of Ni-catalysts with a cylindrical shape (C1) and churros shape structure (C2) were compared for the assessment. Optical microscopy and FESEM were used to analyze the shape and microstructure of the Ni-catalyst. EDS, XRD, and micro-Raman characterization were performed to examine the composition and properties. BET and Pulse Titration analyses were conducted to check the surface area and catalytic property of the Ni-catalyst. From the composition analysis results, C1 contained a relatively large amount of graphite as an impurity, and C2 contained higher Ni contents than C1. From specific surface area analysis, the specific surface area of C2 was approximately 1.69 times larger than that of C1. From catalytic property analysis, outstanding performance in O₂ and CO impurity removal was observed at room temperature. Therefore, C2, having low-impurity and large specific surface area, is a suitable catalyst for the high-purity inert gas process in the semiconductor industry because of its outstanding performance in O₂ and CO impurity removal at room temperature.

• Journal of Surface Science and Engineering
• /
• v.47 no.1
• /
• pp.39-47
• /
• 2014

The peculiar feature of cathodic protection in seawater has the capability to form mineral calcareous deposits such as magnesium and calcium on metal surfaces. It is assumed that $OH^-$ ions are generated close to the metal surface as a result of cathodic protection and generated $OH^-$ ions increases the pH of the metal/seawater interface outlined as the following formulae. (1) $O_2+2H_2O+4e{\rightarrow}4OH^-$, or (2) $2H_2O+2e{\rightarrow}H_2+2OH^-$. And high pH causes precipitation of $Mg(OH)_2$ and $CaCO_3$ in accordance with the following formulae. (1) $Mg^{2+}+2OH^-{\rightarrow}Mg(OH)_2$, (2) $Ca^{2+}+CO{_3}^{2-}{\rightarrow}CaCO_3$. The focus of this study was to increase the amount of $CO{_3}^{2-}$ with the injection of $CO_2$ gas to the solution for accelerating process of the following formulae. (1) $H_2O+CO_2{\rightarrow}H_2CO_3$, (2) $HCO^{3-}{\rightarrow}{H^+}+CO{_3}^{2-}$. Electrodeposit films were formed by an electro-deposition technique on steel substrates in solutions of both natural seawater and natural seawater dissolved $CO_2$ gas with different current densities, over different time periods. The contents of films were investigated by scanning electron microscopy(SEM) and X-ray diffraction(XRD). The adhesion and corrosion resistance of the coating films were evaluated by anodic polarization. From an experimental result, only $CaCO_3$ were found in solution where injected $CO_2$ gas regardless of current density. In case of injecting the $CO_2$ gas, weight gain of electrodeposits films hugely increased and it had appropriate physical properties.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2017.05a
• /
• pp.164-164
• /
• 2017

해양환경 중 많이 사용되는 철강재료들은 그 가혹한 부식환경에 대응하기 위하여 일반적으로 피복 도장방식법이나 음극방식법이 적용되고 있다. 여기서 음극방식법은 선박 및 해양구조물의 해중부 부식에 대해 가장 효과적인 방식법으로 알려져 있다. 한편, 이와 같이 해수 중 철강재에 음극방식을 적용할 경우, 피방식체인 그 강재 표면에 해수 중 용존된 산소의 음극환원 반응이 일어나며 국부적인 알카리 표면 조건을 형성시켜 $Mg(OH)_2$와 $CaCO_3$의 막을 석출시킨다. 이와같이 음극방식 중 형성된 전착물은 방식해야 될 표면적을 감소시켜 방식전류밀도를 감소시키는 효과가 있는 것으로 보고되고 있다. 이렇게 석출된 전착물은 음극표면에 부분적으로 형성되고, 여러 가지 환경 조건 등의 영향을 받아 그 피막의 형성 정도도 가늠하기 어렵기 때문에 음극방식 설계 시 그 정도에 따른 영향을 고려-반영하기가 곤란하다. 또한 이 전착물은 그 형성 메커니즘에 관한 해석이나 강도, 균일한 밀착성, 장기적인 방식효과 및 효율성 등이 아직 충분히 입증되어 있지 않은 실정에 있다. 따라서 본 연구에서는 해수 중 다양한 전착 프로세스에 의해 제작된 전착물의 기간별, 도장코팅 종류별 특성변화를 분석 및 평가하고, 전착물에 의한 희생양극 소모전류 변화 측정 분석을 통해 전착막을 균일하고 치밀하게 형성시키기 위한 최적의 조건을 찾고자 하였다. 또한 석출속도, 밀착성 및 내식특성을 향상시키기 위해 해수 중 기체를 용해시켜 제작한 막의 특성을 분석-평가하였다. 본 연구에 사용된 강 기판은 일반구조용강(KS D 3503, SS400)으로 ${\varnothing}42.7{\times}1,000mm{\times}4.0t$의 형상으로 제작하였다. 인가된 전류밀도는 1, 3 및 $5A/m^2$이고 도장 코팅 종류별 전착 석출물의 형성차이 비교 분석을 위한 실험은 선박 및 해양구조물에 많이 사용되는 Universal Epoxy 도료 2종을 선정하여 진행하였다. 또한 Steel Wire Mesh의 영향을 알아보기 위해 Mesh를 설치하여 실험을 진행하였다. 기간별-도장 종류별 외관관찰, 전착물의 두께 측정, SEM, EDS 및 XRD를 통해 막의 모폴로지, 조성원소 및 결정구조를 분석하였으며, 전착물의 내식성과 내구성을 평가하기 위해 테이핑 테스트(Taping Test) 및 전기화학적 양극분극 시험을 실시하였다. 희생양극 소모율에 대한 전착물의 영향을 확인하기 위해 외부전원을 인가하여 전착 피막을 형성시킨 강 기판에 희생양극을 연결하여 희생양극 소모효율 측정 시험을 진행하였다. 전착물의 석출량은 시간 및 전류밀도의 증가에 따라 비례하여 증가하였으며, 음극전류 인가 시 금속과 용액 계면 사이의 확산층에서 발생한 $OH^-$ 이온으로 인해 금속과 용액 계면 사이 pH가 부분적으로 증가하여 $Mg(OH)_2$ 화합물이 많이 생성되는 것으로 확인되었다. 또한 Mesh의 부착으로 평활하지 않게 형성된 미세한 굴곡구조 및 표면적 증가로 인하여 단계적으로 피복되는데 필요한 시간이 지연되면서 $CaCO_3$에 비해 $Mg(OH)_2$ 화합물이 상대적으로 증가한 것으로 사료된다. $CaCO_3$(Aragonite) 구조는 견고한 피막으로 치밀하고 화학적 친화력이 높아 우수한 밀착성을 보였으며 전착물의 영향으로 양극 전류가 감소하였고, 이로인해 방식전류 절감효과를 얻을 수 있을 것으로 기대된다.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.32 no.7
• /
• pp.965-970
• /
• 2003

This study has been performed to develope a method for the simultaneous determination of 1,4-dioxane (DOX), epichlorohydrin (EPC), propylene chlorohydrin (PCH), ethylene chlorohydrin (ECH) and 1,3-dichloro-2-pro-panol (DCP) in polysorbates, chloline chloride, choline bitartrate, modified starch and spices by purge and trapgas chromatography. Experimental design was used to select a suitable trap by measuring the limit of detection (LOD) and to investigate the effect of temperature and salt of extraction, and the percentage of recovery in various matrix. The LOD of DOX, EPC, PCH, ECH and DCP were 1.38$\mu\textrm{g}$, 0.23$\mu\textrm{g}$, 3.30$\mu\textrm{g}$, 3.97$\mu\textrm{g}$, 20.43$\mu\textrm{g}$ respectively, by means of using Vorcarb 3000 trap with 5$0^{\circ}C$ sample sparger. Excluding EPC, the recoveries of target compounds were above 90% in all matrix. Target compounds in polysorbates (17), choline chloride (5), choline bitartrate (5), modified starch (8) and spices (25) were not detected. But 2.5 ppm of DOX was detected in Tween 80.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.23 no.5
• /
• pp.345-357
• /
• 2011

Recently, as part of diversifying energy sources and earth environmental issues, technology development of new renewable energy using wave energy is actively promoted and commercialized around Europe and Japan etc. In particular, OWC(Oscillating Water Column) wave power generation system using air flow induced by vertical movement of the water surface by waves in an air-chamber within caisson is known as the most efficient wave energy absorption device and therefore, is one of the wave power generation apparatus the closest to commercialization. This study examines air flow velocity, which operates turbine(Wells turbine) directly in oscillating water column type wave power generation structure from two-and three-dimensional numerical experiments and discusses optimal shape of oscillating water column type wave power generation structure by estimating the maximum flow rate of air according to change in shape. The three-dimensional numerical wave flume was applied in interpretation for this study which is the model for the immiscible two-phase flow based on the Navier-Stokes Equation. From this, it turned out that size of optimal shape appears differently according to the incident wave period and air flow is maximized at the period where minimum reflection ratio occurs.