• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.24 no.7 s.178
• /
• pp.1731-1739
• /
• 2000

The Vibration signals of a gear driving system is often associated with gear tooth faults. Many studies have been done on the detection of impulsive vibration signals, which characterize the breaka ge of a gear tooth. Also, most of the studies on gear fault diagnosis are only about the fault existence at one gear-pair. This study concerns on the several possible faults of a geared motor that has three gear pairs. The measurement and analysis on the vibration signals of a running geared motor shows the relationship between the gear faults and the vibration signals. This study also shows that adaptive interference canceling technique can be appropriately applicable to detect which gear-pair has the fault, and that wavelet is better than spectrogram to figure out the gear fault.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.13 no.5
• /
• pp.341-347
• /
• 2003

This paper presents an improved escalator dynamic model so as to reflect the experimental observation on the pseudo-resonance affected by load applied. The experimental evidence reveals that backlash on gearbox as well as sag of driving Chain are most critical factors to the pseudo-resonance in escalators. The dynamic model effectively reflects vibration characteristics measured in real escalators with respect to different conditions of driving chain and the number of passengers. For validation of the dynamic model developed. numerical results from the model are compared with experimental results. The developed model and its simulation results are used rigorously for the design of escalator systems in enhancing the ride comfort.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.11b
• /
• pp.238-243
• /
• 2002

This paper presents an improved escalator dynamic model so as to reflect the experimental observation on the pseudo-resonance affected by load applied. The experimental evidence reveals that backlash of gearbox as well as sag of driving chain are most critical factors to the pseudo-resonance in escalators. The dynamic model effectively reflects vibration characteristics measured in real escalators with respect to different conditions of driving chain and the number of passengers. For validation of the dynamic model developed, numerical results from the model are compared with experimental results. The developed model and its simulation results are used rigorously for the design of escalator systems in enhancing the ride comfort.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.11a
• /
• pp.329.2-329
• /
• 2002

This paper presents an improved escalator dynamic model so as to reflect the experimental observation on the pseudo-resonance affected by load applied. The experimental evidence reveals that backlash of gearbox as well as sag of driving chain are most critical factors to the pseudo-resonance in escalators. The dynamic model effectively reflects vibration characteristics measured in real escalators with respect to different conditions of driving chain and the number of passengers. (omitted)

• Journal of the Korean Institute of Gas
• /
• v.26 no.2
• /
• pp.9-13
• /
• 2022

Electric wheelchairs, the output from the motor is mainly applied to a speed reducer using a power transmission device such as a belt or a chain. However, although a speed reducer using a belt or chain is a simple device, it occupies a lot of space and has a space limitation, so it is not suitable for an electric wheelchair driving part. However, since the speed reducer of the planetary gear type is decelerated on the same axis, the volume can be reduced, so the space constraint is less than that of the belt or chain type reducer. Therefore, in this study, a driving part that can obtain great propulsion with a speed reducer using a planetary gear type was developed through a study on the driving part of a wheelchair that can be switched between manual and electric. Accordingly, the tooth shape of the planetary gear applied to the reducer was designed using the Kisssoft program. In addition, the drive part was designed to be applicable to the existing wheelchair wheels, and the mechanism was optimized for the manual/electric switching principle and operation principle of the drive part. Based on the research contents, the final design and manufacture of the wheelchair reducer drive unit in the form of a planetary gear having one sun gear, two planetary gears and one ring gear was carried out.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.22 no.1
• /
• pp.119-125
• /
• 2012

This paper proposes a model for a chainless power assistor system(PAS) that can provide the required power based upon operational status by designing a chainless electric bicycle that can be substituted for a general chain type bicycle and which is also an environmentally friendly means of transportation. This paper designed a fuzzy control algorithm that can intelligently examine operational status through the stopping force sensor of a chainless intelligently auxiliary power system it and also have the power of an auxiliary power system to be controlled by the vehicle's operational status. This paper designed an intelligent electric bicycle that provides auxiliary power to a general bicycle system relying only upon the stepping force of a human and systems to provide auxiliary power to the intelligent chainless bicycle model designing presented.

• Journal of the Institute of Electronics Engineers of Korea TE
• /
• v.39 no.2
• /
• pp.90-94
• /
• 2002

This paper is related to remote meter-reading using magnetic sensor. Scan system which is developed recently has week point of temperature, humidity, dust, oscillation To solve these problems, this study used magnetic action to measure the consumption of gas. Gas consumption was detected by interaction of a permanent magnet and hall element. Permanent magnet was pasted on rolling change-gear in normal gas meter and hall sensor was pasted on the external wall of normal gas meter. This experiment proved high accuracy and wasn't influenced by temperature, humidity, oscillation and dust

• Proceedings of the KIEE Conference
• /
• 2003.07d
• /
• pp.2396-2398
• /
• 2003

세 개의 체인으로 구성된 병렬형 3 자유도 기구는 특이점을 지님으로 인하여 햅틱기구로 활용시 불특정한 힘반영으로 인해 제한요소가 발생한다. 본 논문은 여유구동을 활용함으로써 특이점을 해소하고, 힘반영의 크기를 증가시킴으로써 햅틱기구의 성능을 향상시키는 것을 목적으로 한다. 또한 여유구동 모터를 베이스에 부착함으로써 관성력을 최소화 시키고, 와이어와 기어비를 활용하여 부드럽고 큰 힘반영 능력을 가능케 했으며, 시뮬레이션을 통해 힘반영 성능을 확인하였다.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.19 no.5
• /
• pp.674-682
• /
• 2009

The modular robot is one which was developed to get over limit of the space movement for the mobile robot. The chain type robot in particular is connected by series each other and this form expression method is simple and easy to really make a docking method efficiently. However, the related studies were focused on the movement that used to be combination, and the movement of a cell independent mainly does not consist and have a problem to dock only in a direction, not to be connected with all directions. Therefore, we suggested a modular structure for quick, independent movement to solve such a problem and had own autonomy. In addition, we are intended to get some effectiveness for connection mechanism using one locking motor. In this paper, we dealt with the design for the mechanical and electrical points and docking algorithm including communication method. All of the structure is verified with real action experiment through the shape expressions of various application platform.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 2017.04a
• /
• pp.12-12
• /
• 2017

본 연구에서는 롤러식 양파 파종기의 작동 특성 파악을 위한 동적 시뮬레이션을 수행하였다. 롤러식 양파 파종기의 주요부는 롤러와 포트트레이로 구성된다. 양파 파종기의 작동 특성 파악을 위해 동력전달 경로의 구성요소와 각 주요부의 속도를 분석한 결과 동력원인 모터의 출력은 체인과 스프라켓을 통해 포트트레이와 롤러에 전달되며 모터에서의 회전속도는 1770rpm으로 감속기를 통해 출력축의 회전속도는 17.7rpm으로 감소한다. 이론적으로 도출한 포트트레이의 이동속도는 74.98mm/s, 롤러의 회전속도는 22.13rpm으로 나타났다. 시뮬레이션을 수행하기 위해 스캐너를 이용하여 롤러식 파종기를 실측했으며 후에 3D모델링을 진행하였다. 시뮬레이션 해석조건은 파종기의 실제 작동방식을 고려하여 롤러1과 3은 포트트레이와 면대면 접촉을 통해 회전하도록 설정하였고 롤러2와 롤러4는 동력전달경로에 포함된 스프라켓과 기어의 잇수비를 반영하여 회전속도를 도출하여 적용하였다. 시뮬레이션 결과 롤러의 회전속도는 모두 22.13rpm으로 수식에 근거하여 도출한 값과 계측 값이 같음을 확인하였다. 또한 파종 깊이를 결정하는 요소인 롤러의 상토 압축 정도를 파악하기 위하여 롤러궤적 시뮬레이션을 통해 롤러 끝 단의 궤적을 분석하였는데 롤러궤적 분석 결과 롤러의 끝 단은 약 9.8mm 깊이로 내려가는 것을 확인하였다.