• Analytical Science and Technology
• /
• v.24 no.1
• /
• pp.51-59
• /
• 2011

Genetic Identification has become an important forensic investigation method which discerns identity through analysis of physical samples discovered in various crime scenes. Recently more samples are being requested to undergo A-STR analysis of low copy number (LCN) DNA, which is known as touch evidence-type sample and left on various objects such as a pen briefly used by the criminal, the gear of the car used for driving, the handle, and various buttons inside a car. This research attempted to extract the LCN DNA of the touch evidencetype left on crushed fingerprints on firearms, etc. and examine the genotyping success rate. Four types of firearms (M16, K1A, COLT 45 Pistol, M29 Revolver) were fired individually and physical samples were gathered from four parts of each firearm. Subsequently, in order to extract the LCN DNA, Microkit and $Prepfiler^{TM}$ were used to compare and analyze the quantity of DNA extracted and the genotyping success rate. Analysis results showed that the quantity of DNA extracted by $Prepfiler^{TM}$ was on average 1.7 times higher than that of Microkit, and in genotype analysis success rate $Prepfiler^{TM}$ also demonstrated 24.9% on average in contrast to 0% for Microkit. In regards to the grip part of the K1A, $Prepfiler^{TM}$'s success rate was as high as 50.6%.

• Journal of Digital Convergence
• /
• v.17 no.11
• /
• pp.207-213
• /
• 2019

The fuel-cut coast-down driving mode is activated when the acceleration pedal is released with transmission gear engaged, and it's a default function for electronic-controlled engine of vehicles. The fuel economy becomes better because fuel injection stops during fuel-cut driving mode. A fuel-cut detection method is suggested in the study and it's based on the speed, acceleration and road gradient data from GPS sensor. It detects fuel-cut driving mode by comparing calculated acceleration and realtime acceleration value. The one is estimated with driving resistance in the condition of fuel-cut driving and the other is from GPS sensor. The detection accuracy is about 80% when the method is verified with road driving data. The result is estimated with 9,600 data set of vehicle speed, acceleration, fuel consumption and road gradient from test driving on the road of 12km during 16 minutes, and the road slope is rather high. It's easy to detect fuel-cut without injector signal obtained by connecting wire. The detection error is from the fact that the variation range of speed, acceleration and road gradient data, used for road resistance force, is larger than the value of fuel consumption data.

• (The) Research of the performance art and culture
• /
• no.39
• /
• pp.801-833
• /
• 2019

This article has reviewed on the characteristics of the Beompae (Buddhist chanting) performed by Gyeongjaeeosan Wonmyeongchang(唱) based on the result of musical style of Gyeongjae Anchaebi-sori as defined under the previous studies. And, through the comparison with the Beompae performed by Songam-chang (唱), a same type of musical piece, it contemplates on musical differences between the two singers. Results of the study are shown as follows. of Gyeongjaeeosan Seolhoeinyu-pyeon and of Socheongsaja-pyeon are sunged as Yuchi-Seong(聲) among Anchaebi-sori. 'main melody type' and 'ending type' are generally similar to the musical characteristics of the Yuchi-Seong(聲), and the differences between the two singers are detected from main melody type D and ending type b. In particular, under of Socheongsaja-pyeon, only the type a is detected among the two types. becouse ending note of ending-type 'a' is ended with 'sol'. The basic frame of the Jjaimsae(musical form) has been clarified in the previous studies that the Jjaimsae of Yuchi-Seong(聲) has been maintained just the way it is. However, even for the same Seong(聲), the combination of the 'main melody type' of passage has not been unified, and depending on the musical piece, it has been discovered that the combination of the 'main melody type' has been diversely organized. of Gyeongjaeeosan Bongsongsajapyeon belongs to Pyeon-gae-seong(聲) broadly from the Anchaebi-sori and it is shown to be So-seong(聲) in details. In particular, in the previous studies, the 'ending melody' of So-seong(聲) and the closing melody of were similar with a slight difference for the 'ending melody'. Such a difference is relation to the characteristics for sequentially descending melody of Wonmyeong-chang(唱). The 'Jjaimsae(The musical structure)' is not much different from the previous studies, and the 'yeok-eum(weaving lyrics)' of Songam-chang(唱) has strong tendency of 3-sobak rhythm while the Wonmyeong-chang (唱) is shown the tendency of 2-sobak rhythm in general for the difference.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 2017.04a
• /
• pp.76-76
• /
• 2017

4륜 승용관리기는 보통 후방이나 전방에 작업기를 장착하여 작업하나 3륜 승용관리기는 작업기를 복부에 장착함으로 작업의 정밀도, 편이성, 관측의 용이성 향상과 함께 지상고 제고, 차폭 조절, 조향 등의 성능 개선을 기할 수 있다. 국내에서는 3륜 승용관리기용 복부 장착 부속작업기가 거의 개발되어 있지 않으며, 특히 두류 재배에 있어서 일관기계화 작업을 위한 관리작업기의 개발이 매우 필요한 실정이다. 승용관리기의 중경배토기에 의한 작업은 기존 인력에 의한 작업보다 약 87%의 노력을 절감할 수 있으며, 잡초방제 효과도 인력에 비하여 크게 떨어지지 않고, 수량도 증가하는 것으로 보고되고 있다. 따라서 본 연구는 3륜 승용관리기에 적합한 복부장착형의 중경배토기를 설계 제작하였다. 3륜 승용관리기용 중경배토기는 승용관리기의 복부 PTO에서의 구동력 전달을 위한 연결 조인트, 중간축, 기어 및 체인 전동기구, 구동축으로 구성된 동력전달부, 4개의 로타리 날과 후방 1개의 배토날로 구성된 3조의 작업날, 로타리 날과 배토날의 경심 조절을 위한 3조의 바퀴, 흙의 비산 방지를 위한 로타리날 커버 및 케이스, 다양한 조간거리에 적응을 위한 조간조정 나사부, 3륜 승용관리기에의 부착을 위한 프레임 및 부착보조 작업기 이동용 바퀴장치 등으로 구성 설계 제작하였다. 로타리 날과 배토날은 기존 시판 관리기용 날을 사용하였다. 로타리 날은 진행방향으로 회전하도록 하였으며, 날의 회전반경은 약 330 mm, 조당 경운 폭은 약 230 mm 설계하였다. 최대 경심은 100 mm이며, 조간거리의 조절범위는 수동 나사에 의하여 620~900 mm 범위로 무단조절 할 수 있도록 하였다. 중경제초기는 3륜 승용 관리기 복부의 평행링크에 부착되므로 작업기의 이동 및 부착 편이를 위하여 이동용 바퀴를 설치하였다. 제작된 중경배토기의 크기는 길이${\times}$폭${\times}$높이가 $660{\times}2072{\times}880mm$, 중량은 약 200 kg으로 제작되었다.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 2017.04a
• /
• pp.75-75
• /
• 2017

3륜 승용관리기는 4륜 승용관리기에 비하여 작업기를 복부에 장착함으로 작업의 정밀도, 편이성, 관측의 용이성 향상과 함께 지상고 제고, 차폭 조절, 조향 등의 성능 개선을 기할 수 있다. 국내에서는 3륜 승용관리기용 복부 장착 부속작업기가 거의 개발되어 있지 않으며, 특히 두류 재배에 있어서 일관기계화 작업을 위한 관리작업기의 개발이 매우 필요한 실정이다. 콩의 순 지르기 작업은 콩이 지나친 생육을 한 경우 미리 줄기의 윗부분을 제거하는 저심처리를 해주면 곁가지들의 왕성한 생육을 유도하여 많은 꼬투리를 얻고 쓰러짐도 줄어들어 수량을 높일 수 있다. 순 지르기 작업은 보통 낫이나 배부식 예취기를 이용하여 작업함으로 노동력이 많이 들고 작업부담이 심하여 개선이 필요한 실정이다. 따라서 본 연구는 3륜 승용관리기에 적합한 복부장착형의 순 지르기 작업기를 설계 제작하였다. 3륜 승용관리기용 순 지르기 작업기는 승용관리기의 복부 PTO에서의 구동력 전달을 위한 연결 조인트, 중간축, 기어 전동기구, 구동축으로 구성된 동력전달부, 2 조의 원판형 작업 날, 다양한 조간거리에 적응을 위한 조간조정 나사부, 3륜 승용관리기에의 부착을 위한 프레임 및 부착보조 작업기 이동용 바퀴장치 등으로 구성 설계 제작하였다. 원판형 칼날은 시판 중인 예취기의 외경 305 mm, 칼날 톱니 수 90개의 초경 비트 부착 날을 사용하였다. 작업 날의 승강높이는 150~540 mm 범위로 조절하도록 하였다. 조간거리의 조절범위는 수동나사에 의하여 660~860 mm 범위로 무단조절 할 수 있도록 하였다. 순 지르기 작업기는 3륜 승용 관리기 복부의 평행링크에 부착되므로 작업기의 이동 및 부착 편이를 위하여 이동용 바퀴를 설치하였다. 제작된 순 지르기 작업기의 크기는 길이${\times}$폭${\times}$높이가 $514{\times}1138{\times}810mm$, 중량은 약 100 kg으로 제작되었다.

• Proceedings of the KSR Conference
• /
• 2007.05a
• /
• pp.786-791
• /
• 2007

Korean high speed train(HSR-350x) has adopted a combined electrical and mechanical(friction) braking system. Brake blending control unit(BBCU) controls each brake system to fulfill the required brake performances such as braking distance, deceleration and jerk. Also the braking system should be designed considering the economical management, such as effective use of generated braking energy and the minimum wear of friction materials(a pad and a brake shoe). In this paper, we establish the disc braking force pattern that reduces the wear of pad in the disc braking system by minimizing the variance of the instantaneous disk baking energy during braking time, and compare the wear mass of pad between the conventional disc braking force pattern and the established results.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.6
• /
• pp.74-79
• /
• 2019

The military vehicle produces electric power through an engine-integrated serial hybrid generator that is connected to the engine and does not have a separate generator installation space. However, depending on the mechanical characteristics of the connection between the generator and the engine, iron oxide for internal rusting and lubrication grew scattered. The iron oxide is adhered to the starter to deteriorate the starting performance, and there is a problem that the noise of the leg due to wear of the gear is increased. To solve this problem, the connection spline material and the surface treatment of the engine were improved and the shape was changed to a grease sealing type to prevent the generation of iron oxide inside. As the shape of the generator connector composing the shafting system was changed, the integrity of the structure was confirmed through the torsional endurance test. In addition, through the actual vehicle load test, it was verified that no corrosion occurred during the target life span without internal corrosion. It was confirmed that the anti-scattering structure of the grease effectively suppresses the generation of iron oxide, thereby reducing the noise generated from the generator. In this paper, we propose a fundamental solution to the degradation of the starter and the noise generation by preventing the back corrosion caused by the serial hybrid generator installed between the engine and the transmission.

• The Korean Journal of Archival Studies
• /
• no.38
• /
• pp.125-187
• /
• 2013

This essay would focus on a kinds of new archival strategy. The main frame has been the kinds of activities regulated by laws, or formal activities since 1999. In the case of presidential archives has no another frame. There had never kinds of presidential archives system until President Noh, if anything. It means that the frame has some important points. Although it is, we have to say about the limits of the frame. This essay show 'metaphor frame' for archival system. I think that we have to guess there are methodologies below the two frames. One is quantitative study methodology, and another is qualitative research methodology. The later focuses on the experiences for making narratives. We have to know that this methodology is out of fashioned in the field of history department and cultural anthropology department for the purpose of alternative studies. This essay says about 'archival field description' and 'narrative records' for the new records in archival field. I have to say about that we needs to discuss about kinds of new archival discours. And to conclude, we should manage the records in culture.

• Ecology and Resilient Infrastructure
• /
• v.9 no.1
• /
• pp.15-23
• /
• 2022

This study was conducted to investigate in relation to characteristic of macroinvertebrates in conventional and organic paddy fields. The investigation was conducted five times a year for Suwon, Ansung, Boeun, Gunsan, Gimje, Hamyang, divide into conventional paddy fields and organic paddy fields from 2009 to 2011. The macroinvertebrates collected from the surveyed between conventional and organic paddy fields belonged to 84 species, 47 families, 16 orders, and 6 classes in 3 phyla. In the habitat orientied groups, climbers, swimmers and sprawlers were considerably occupied in conventional and organic paddy fields. In relation to the functional feeding groups, predators such as Odonata, Coleoptera, and Hemiptera were only the highest in paddy field ecosystem, regardless of cultivation method. As a result of community stability analysis, orgainc paddy fields has been identified much as species high resistance and resilience to environmental change in paddy field ecosystem. Species belonging to the I groups is considered to be important in organic paddy field such as Sternolophus rufipes, Hydrochara affinis, Helochares nipponicus, which has high mobility. In conclusion, it was found that the introduction of coleoptera as a food source was higher than that of conventional paddy fields in organic paddy field where primary consumers were abundant such as Chironomidae spp. and Dixidae sp..

• The korean journal of orthodontics
• /
• v.31 no.1 s.84
• /
• pp.25-38
• /
• 2001

The purpose of this study was to compare the force, the displacement and the stress distribution on the maxillary first molars altered by the application of various asymmetric head-gear. For this study, the finite element models of unilateral Cl II maxillary dental arch was made. Also, the finite element models of asymmetric face-bow was made. Three types of asymmetric face-bow were made : each of the right side 15mm, 25mm and 35mm shorter than the left side. We compared the forces, the displacement and the distribution of stress that were generated by application of various asymmetric head-gear, The results were as follows. 1. The total forces that both maxillary first molars received were similar in all groups. But the forces that mesially positioned tooth received were increased as the length of the outer-bow shortened, and the forces that normally positioned tooth received were decreased as the length of the outer-bow shortened. 2. In lateral force comparison, the buccal forces that normally positioned tooth received were increased as the length of the outer-bow shortened, and the buccal fortes that mesially positioned tooth received were decreased as the length of the outer-bow shortened. Though the net lateral force moved to the buccal side of normally positioned tooth as the length of the outer-bow shortened, both maxillary first molars received the buccal force. That showed 'Avchiai Expansion Effect' 3. The distal forces, the extrusion forces and the magnitudes of the crown distal tipping that mesially positioned tooth received were increased as the length of the outer-bow shortened, and the forces that normally positioned tooth received were decreased as the length of the outer-bow was shortened. 4. The magnitude of the distal-in rotation that normally positioned tooth received were increased as the length of the outer-bow was shortened. But, mesially positioned tooth show two different results. For the outer-bow 15mm shortened, mesially positioned tooth showed the distal-in rotation, hut for the outer-bow 25mm and 35mn shortened, mesially positioned tooth showed the distal-out rotation. Thus, the turning point exists between 15mm and 25mm. 5. This study of the initial stress distribution of the periodontal ligament at slightly inferior of the furcation area revealed that the compressive stress in the distobuccal root of the normally positioned tooth moved from the palatal side to the distal side and the buccal side successively as the length of the outer-bow shortened. 6. This study of the initial stress distribution of the periodontal ligament at slightly inferior of the furcation area revealed that the magnitudes of stress were altered but the total stress distributions were not altered in the mesiobuccal root and the palatal root of normally positioned tooth, and also three roots of mesially positioned tooth as the length of the outer-bow shortened.