• Journal of Powder Materials
• /
• v.6 no.1
• /
• pp.27-35
• /
• 1999

A study was made on the fabrication of nanostructured Fe-Co powders by mechanical alloying and their magnetic properties. Microstrural development during the process of MA was inverstigated by means of X-ray diffraction, differential thermal analyzer, scanning electron microscopy and transmission electron microscopy. The magnetic properties of NS Fe-Co powders were evaluated through the measurements of the saturation magnetization $(M_s)$ as well as the coercivity $(H_c)$. The average grain size calculated from line braodening in XRD peak was about 10nm or less and confirmed by TEM. In this experiment, two different milling methods (cycle opertion and conventional milling) were used. Cycle operation had an advantage over the conventional milling method in that more refined powders can be obtained. Solid state alloying of the components was confirmed from both the change of the saturation magnetization and the change of lattice parameter with Co contentration. Maxium $M_s$ was obtained at the composition of 30at.%Co. Relatively high coercivities of 10~150e were obtained for the compositions investigated, and this seems to be due to the high amount of internal strain introduced during milling.

• Journal of Powder Materials
• /
• v.26 no.2
• /
• pp.107-111
• /
• 2019

The activation energy to create a phase transformation or for the reaction to move to the next stage in the milling process can be calculated from the slop of the DSC plot, obtained at the various heating rates for mechanically activated Al-Ni alloy systems by using Kissinger's equation. The mechanically activated material has been called "the driven material" as it creates new phases or intermetallic compounds of AlNi in Al-Ni alloy systems. The reaction time for phase transformation by milling can be calculated using the activation energy obtained from the above mentioned method and from the real required energy. The real required energy (activation energy) could be calculated by subtracting the loss energy from the total input energy (calculated input energy from electric motor). The loss energy and real required energy divided by the reaction time are considered the "metabolic energy" and "the effective input energy", respectively. The milling time for phase transformation at other Al-Co alloy systems from the calculated data of Al-Ni systems can be predicted accordingly.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.28 no.6
• /
• pp.250-255
• /
• 2018

The CoCrMo as-built alloys prepared by 3D-printing process are studied on tensile strength, wear resistance, crystal structure and microstructure after complex heat-treatment including HIP. In this study, HIP treatment for removing micropores, ambient heat-treatment for formation of metal carbides, and solution heat-treatment for homogenization of the created metal carbides were tried and characterized for applying to artificial joint. The complex heat-treatment effects of the CoCrMo as-built alloys prepared by 3D-printing process were owing to the densification during HIP, formation of metal carbides and homogenization of the created metal carbides. The effects of the complex heat-treatment were confirmed by XRD, FE-SEM and EDS.

• Journal of the Korean Society for Railway
• /
• v.13 no.2
• /
• pp.131-138
• /
• 2010

Recently, extruded aluminium-alloy panels have been used in the car bodies in order to meet the needs for the speed-up and light-weight of the railway vehicles. Most of the car bodies were jointed by arc weldings, like GMAW (GasMetal Arc Welding) and GTAW (Gas Tungsten Arc Welding), but these weldings became fairly worse the mechanical properties of the junction than the base metal. Nowadays, FSW (Friction Stir Welding), which is superior to the arc weldings, has been applied in the railway vehicles. In this study, the mechanical properties of the joints in both FSW and GMAW for A6005 extruded aluminium-alloy sheets have discussed. In addition, the relationships between the welding conditions and the mechanical properties for the joint of FSW have analyzed through the sensitivity analysis. It can be concluded that the mechanical properties for the joint of FSW are better than those of GMAW and the welding speed is the most sensible welding condition in the process of FSW.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2002.11a
• /
• pp.36-36
• /
• 2002

최근 한국기계연구원에서 개발된 Mechanochemical process (MCP)는 Spray conversion 법에 의하여 나노크기의 W/Cu 복합 분말을 제조하는 방법으로서, 현재 (주)나노테크에서 산업화를 위한 시험/개발이 진행 중이다. 이 방법에 의하여 W /1 0 ~ 40wt. %Cu 조성의 초미렵 W/Cu 복합 분말의 양산화가 가능하게 됨으로써, 나노복합분말을 사용한 초미립 W/Cu 합금의 소결 제조 연구 역시 나 노태크에서 분말사업화와 동시에 수행되고 있다. 현재 Spray conversion 법으로 제조되고 있는 W/Cu 나노복합분말 및 그 소결체는 Cu의 조성범 위에 따라 민수용 및 군수용 제품으로의 적용이 시도되고 있으며, 각기 특성향상을 목표로 각 적용 분야에서 요구되는 제반 성능에 대한 검토가 이루어지고 있다. 특히 군수용의 목적으로 사용될 경우, 정적 및 동적부하상태에서 재료의 균일한 변형이 가장 중요한 특성이다. 현 개발품의 경우, 일반 W 빛 Cu 원료에 비하여 상대적으로 높은 순도의 원료를 사용하였기 때문에 분말 및 소재상태 에서의 순도가 높아서, 연성을 저하시키는 것으로 알려진 기지상내 합금원소 또는 interface 게재물 이 존재할 가능성이 매우 낮다. 또한 초미립 W 입자들과 Cu 상의 혼합도가 극대화된 상태이기 때문에 상대적으로 저옹에서도 완전치밀화된 미세조직을 얻을 수 있는데, 이는 분말상태의 균일한 미세구조를 유지할 수 있으며, 동시에 W 업자간의 과도한 neck 형성을 방지함으로써 기계적 변형시 재료의 연성 향상이 기대된다. 이러한 W/Cu 나노복합분말 소결체의 특성은 균일한 밀도분포와 동시에 과도한 동적 부하상태에서 균일한 변형이 보장되어야만 하는 특정 군수용 목적에 잘 부합하는 것으로 판단된다. 본 고에서는 상기한 W/Cu 나노복함분말을 사용하여 균일한 미세구조를 가지는 완전치밀화된 소결재를 제조하는 과정과 제조된 소결재를 향후 군수용 제품에 척용시키기 위하여 진행된 단조특성에 대한 연구결과틀을 재료의 미세구조척 관점에서 논의하였다.

• Korean Journal of Materials Research
• /
• v.11 no.8
• /
• pp.629-635
• /
• 2001

To improve the ductility of $A1_3Hf$ intermetallics, which are the potential high temperature structural materials, the mechanical alloying behavior. the effect of Cu addition on the $Ll_2$ phase formation and the behavior of vacuum hot-pressed consolidation were investigated. During the mechanical alloying by SPEX mill, the $Ll_2 A1_3Hf$ intermetallics with the grain size of 7~8nm was formed after 6 hours of milling in Al-25at.%Hf system. The $Ll_2$ Phase of Al_3Hf$ intermetallics with the addition of 12.5at.%Cu, similar to that of the binary Al-25at.% Hf, was formed, but the milling time necessary for the formationof the $Ll_2$ phase was delayed form 6 hours to 10 hours. The lattice parameter of ternary $Ll_2(Al+Cu)_3Hf$ intermetallics decreased with the increase of Cu content. The onset temperature of $Ll_2$ to $D0_{23}$ phase in $Al_3Hf$ intermetallics was around 38$0^{\circ}C$, the temperature upon completion varied from 48$0^{\circ}C$ to 5$50^{\circ}C$ as the annealing time. The onset temperature of $Ll_2$ to $D0_{23}$ phase transformation in $(Al+ Cu)_3Hf$ intermetallics increased with the amount of Cu and the highest onset temperature of $700^{\circ}C$ was achieved by the Cu addition of 10at.%. The relative density increased from 89% to 90% with the Cu addition of 10at.% in $Al_3Hf$ intermetallics hot-pressed in vacuum under 750MPa at 40$0^{\circ}C$ for 3 hours. The relative density of 92.5% was achieved without the phase transformation and the grain growth as the consolidation temperature increased from 40$0^{\circ}C$ to 50$0^{\circ}C$ in $(Al+Cu)_3Hf$ intermetallics hot-pressed in vacuum under 750MPa for 3 hours.

• Korean Journal of Materials Research
• /
• v.11 no.6
• /
• pp.453-459
• /
• 2001

It is important for the fabrication of nuclear cladding to optimize the microstructure, because the properties of Zr-based nuclear claddings such as mechanical properties, oxidation-resistance and corrosion- resistance vary widely with its microstructure. The microstructure in Zr-based alloy is strongly dependent on the solubility of alloying element. However, it is very difficult to measure the solubility due to the low solution limit of alloying elements in Zr-based alloy. In this study, Thermoelectric Power(TEP) measurements are used to determine the solubility of Nb in Zr-0.8Sn alloy, which is confirmed by optical microscopy and transmission electron microscopy. The solutioning of Nb obtained by a homogenization treatment and water-quench leads to a decrease of TEP The saturation of TEP appears with the increase of homogenization temperature, which means the saturation of the Nb content in the matrix. From these results, the solubility ($C_{Nb}$) of Nb in Zr-0.8Sn with temperature could be expressed as fellow equation : $4.69097{\times}10^{16}{\times}e^{-25300\times\;I/T}$(ppm.at.%)

• Journal of the Korean Magnetics Society
• /
• v.4 no.4
• /
• pp.347-354
• /
• 1994

The structural change and magnetic properties of mechanically milled Fe-N and Mn-Al alloy powders have been investigated by XRD, TEM, VSM, $M\"{o}ssbauer$ spectroscopy and inelastic neutron scattering measurements. During milling of ${\gamma}'-Fe_{4}N$ powders, and fcc ${\gamma}'-Fe_{4}N$ phase is transformed to a bct ${\alpha}'-Fe(N)$ phase by stress-induced martensitic transformation, being accompanied by an initial increase in saturation magnetization. During annealing the bct ${\alpha}'-Fe(N)$ nanocrystalline phase which is obtained by mechanical grinding for a long time, an ${\alpha}'-Fe_{16}N_{2}$ phase partially appears as an intermediate phase at 673~773 K, causing an increase in saturation magnetization. During milling of Mn-45, 70 and 85 at.% Al mixed powders, Al atoms are partially solubilized into an ${\alpha}-Mn$ phase. The Al supersaturated ${\alpha}-Mn-type$ phases change from paramagnetic to ferromagnetic : the saturation magnetization is 11 emu/g for the as-milled Mn-70 at.% Al powders. Moreover, by removing almost all Al atoms from the as-milled Mn-85 at.% Al powders using chemical leaching, the saturation magnetization increases up to 36 emu/g. The above bct ${\alpha}'-Fe(N)$ and ferromagnetic ${\alpha}-Mn$ type alloys are the magnetic materials found for the first time, by using the present mechanochemical process.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.661-661
• /
• 2013

열전재료는 열-전기가 상호 가역적으로 변하는 재료로서, 에너지 변환소재 분야에서 널리 각광받고 있다. 열전재료의 성능은 무차원 열전성능지수(dimensionless figure of merit, $ZT={\alpha}^2{\sigma}T/{\kappa}$)로 평가된다. 여기서 ${\alpha}$는 제벡계수(Seebeck coefficient), ${\sigma}$는 전기전도도(electrical conductivity), ${\kappa}$는 열전도도(thermal conductivity), T는 Kelvin 온도를 나타낸다. 500 K에서 800 K까지의 중온 영역에서 우수한 열전특성을 보이는 $Mg_2X$ (X=Si, Ge, Sn)와 이들의 고용체는 성분원소가 독성이 없고, 매장량이 많아 친환경 열전재료로 각광받고 있다. $Mg_2X$ 고용체 중 $Mg_2Si-Mg_2Sn$ 고용체는 Si와 Sn의 큰 원자량 차이로 인해 낮은 열전도도와 높은 성능지수(ZT)를 얻을 것이라 예상되며 열전발전 소자로서의 응용이 기대된다. Sb가 도핑된 $Mg_{2+x}Si_{0.7}Sn_{0.3}Sb_y$ (x=0, 0.1, 0.2, y=0, 0.01) 고용체를 고상합성과 기계적 합금화로 합성한 후, 진공 열간압축 성형을 통해 성공적으로 제조하였다. X선 회절분석으로 상합성과 고용체 형성 여부를 확인하였고, Mg의 과잉첨가와 Sb 도핑에 따른 열전특성의 변화를 조사하였다.

• Korean Journal of Materials Research
• /
• v.10 no.12
• /
• pp.838-844
• /
• 2000

For the fabrication of titanium diboride($TiB_2$)- based cermet as applications of cutting tools and wear resistant materials, a binder metal with good mechanical properties and sinterability is essential. In this study, SUS316L was chosen for the binder metal to obtain a new $TiB_2$ cermet with superior hardness and toughness.$TiB_2$-SUS316L cermets were densified to relative density of more than 99% by pressureless sintering at temperature above $1650^{\circ}C$ The flexural strength was up to 1290MPa at 10vo1%SUS316L cermet in spite of the formation of $Fe_2$B phase during the sintering. The fracture toughness was obtained up to $6MPam^{1/2}$ with Victors hardness over 18Gpa. These hardness and fracture toughness combinations are better than those of conventional cermet. The high temperature strength remarkably decreased by the plastic deformations of SUS316L binder phase at nearby $800^{\circ}C$ .