• Journal of Biosystems Engineering
• /
• v.25 no.3
• /
• pp.221-226
• /
• 2000

Hot air heater with light oil burner is the most common heater for greenhouse heating in the winter season in Korea. However, since the thermal efficiency of the heater is about 80∼85%, considerable unused heat amount in the form of exhaust gas heat discharges to atmosphere. In order to capture this exhaust heat a heat recovery system for plant bed heating in the greenhouse was built and tested in the hot air heating system of greenhouse. The heat recovery system is made for plant bed or soil heating in the greenhouse. The system consisted of a heat exchanger made of copper pipes, ${\Phi}12.7{\times}0.7t$ located in the rectangular column of $330{\times}330{\times}900mm$, a water circulation pump, circulation plastic pipe and a water tank. The total heat exchanger area is 1.5$m^2$, calculated considering the heat exchange amount between flue gas and water circulated in the copper pipes. The system was attached to the exhaust gas path. The heat recovery system was designed as to even recapture the latent heat of flue gas when exposing to low temperature water in the heat exchanger. According to the performance test it could recover 45,200 to 51,000kJ/hr depending on the water circulation rates of 330 to $690\ell$/hr from the waste heat discharged. The exhaust gas temperature left the heat exchanger dropped to $100^{\circ}C$ from $270^{\circ}C$ by the heat exchange between the water and the flue gas, while water gained the difference and temperature increased to $38^{\circ}C$ from $21^{\circ}C$ at the water flow rate of $690\ell$/hr. By the feasibility test conducted in the greenhouse, the system did not encounter any difficulty in operations. And, the system could recover 220,235kJ of exhaust gas heat in a day, which is equivalent of 34% of the fuel consumption by the water boiler for plant bed heating of 0.2ha in the greenhouse.

• Journal of Navigation and Port Research
• /
• v.42 no.1
• /
• pp.31-38
• /
• 2018

The purpose of this study is to contribute to the study of the prevention of diseases and promotion of health of ocean going vessel crew members, through the medical diagnosis and disease classification efforts of this study. From the second half of 2016 to 2017, the diagnosis and health characteristics of 195 crew members were collected through counseling, treatment, and emergency care for about 1 year and 2 months. As a result, it is noted that the incidence of diseases was in the order of urticaria (5.6%), lumbar sprain (4.1%), acute gastroenteritis (3.1%) and anxiety (3.1%). In categorical review, the incidence of musculo-skeletal disease was the most common (25.1%) which was followed by skin disease (17.9%) and digestive disease (11.3%). In addition, the disease that was noted as was the most common in the under 30 years old category, and the incidence of the disease was high in the crew group. Finally, there was a difference between the pathogenesis (trauma vs disease, etc.) (p <.001) and the type of vessel (merchant ship and fishing vessel) (p <.005) as noted in this case.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.10
• /
• pp.5933-5938
• /
• 2014

In this study, the effect of varying the mixture gas during FCA welding was studied for an Atos 60 test piece. To examine the characteristics of welding, the weldability of the material was checked before welding and online monitoring was performed to examine the mechanical properties after welding. The mixture Ar 80% + $CO_2$ 20% at low speed gave very elegant beads with very little spatter. 100% $CO_2$ gave rise to high spatter generation. For Ar 80% + $CO_2$ 20%, the low current region due to the normal short circuits created spatter, which was more than double for 100% $CO_2$. This peak distribution occurred due to the instability of the arc. The tensile test result for Ar 80% + $CO_2$ 20%, Ar 90%+ $CO_2$ 10% and $CO_2$ 100% at 511MPa, 507MPa, and 469MPa showed that the yield strength was improved by 8.1 and 8.9% for 80%+ $CO_2$ 20% and Ar 90%+ $CO_2$ 10%, respectively, compared to 100% $CO_2$. The tensile test result at 622MPa, 609MPa, and 581MPa showed that the yield strength was improved by 7.0% for both the mixture gas compared to 100% $CO_2$.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.06a
• /
• pp.154-154
• /
• 2006

Samsung Electro Mechanics ink jet has developed ultra high resolution alignment system. The alignment system has been developed for repeatable printing of conductive ink. The resolution of alignment system is 0.5um and the velocity of printing working plate is 1.5m/s. So far repeated printing results included sintering process have over 30um of drop mislocation data. In order to improve line thickness and conductivity of metal line, we need to develop the higher mechanical accurate align system. On the demand, this developed align system has under $1{\sim}2{\mu}m$ mispositioning performance and can measure of mechanical accuracy of inkjet printer, as well as the straightness of jetted drop from inkjet head. There is no kinds limit of substrate and ink to use SEM alignment system. By using this alignment system, we progress two experiment of reiterate printing drop and making conductive line on the glass and photo paper. Optical microscope and 3D profiler has been used for measurement of printed ink.

• Journal of radiological science and technology
• /
• v.33 no.4
• /
• pp.387-394
• /
• 2010

In the field of healthcare, the conventional sterilization treatments have been replaced by irradiation methods which are in accordance with internationally well established quality standards. The quality control in radiation sterilization assures that the absorbed dose of the irradiated material is in agreement with its requirements and standards. The electron beam irradiation requires technical assessments of more process parameters than gamma irradiation does. Korea has witnessed wide uses of electron accelerators since early 2000 but there hasn't been research experiences relating to quality system in accordance with international standards. The new large scale e-beam irradiation system with the specification of 10 MeV, 8 kW was installed and operated in 2008 by Seoul Radiology Services Co. It consists of the electron accelerator, product handling system, safety, documentation and control subsystems into an integrated system to meet the requirement of the Good Manufacturing Practice such as process quality assurance and management of product tracking records. To implement the international standard such as EN ISO11137, it is necessary to understand the purposes aimed in the standard and carry out the tests following the procedures required. This study presented the specification of the e-beam facility and showed what its design requirements and features are. The test results on a variety of process parameters were presented and validated it they are within the required limits.

• Applied Chemistry for Engineering
• /
• v.27 no.2
• /
• pp.221-226
• /
• 2016

Production of eco-friendly and biologically harmless materials is strongly required in all industries. In particular, reducing volatile organic compounds in coating processes is extremely important to secure worker's safety. During recent two decades, extensive research works on water-borne polyurethane dispersion (PUD) have been continuously developed as an alternative to solvent-borne polyurethane. However, PUD was shown inferior mechanical properties to the organic solvent-borne polyurethane due to a limit to the molecular weight increase, which resulted in the limit of applications. To overcome this drawback, several approaches have been examined such as polymer blends and thermal/radiation induced crosslinking. Among these methods, the radiation curing system was suitable for industrialization because of the high crosslinking density and fast curing speed. In this study, we overcame the drawback for PUD via introducing benzophenone radiation curable units to PUD. We synthesized PUD films which possessed good dispersion in water for 30 days, increased Tg and Td more than $5^{\circ}C$ after UV curing film as well as improved young's modulus more than double.

• Journal of Biomedical Engineering Research
• /
• v.19 no.2
• /
• pp.163-170
• /
• 1998

The ultimate goal of total artificial heart is permanent substitute for a failed heart in a patient without any other therapeutic modality. Until now, infection has been the main problem related to the mechanical circulatory support system. The best way to solve this catastrophic complication and to improve the quality of life of TAH patients in terms of tethering must be implantation of TAH totally. The EH-TAH has been developed in NCVC from 1987 for this purpose. The system consists of an energy converter and pumps, which are designed to be placed in abdomen and pericardial space separately for a good anatomical fit. To evaluate the anatomical fit and hemodynamic performance of the EH-TAH, in vivo test was done. General condition of the animal and hemodynamic status had been stable until the TAH stopped on the 11th pumping day. The estimated cardiac output was about 7.7L/min. The values of mean aortic pressure, left and right atrial pressure were 93$\pm$10, 19$\pm$3 and 15$\pm$4 mmHg, respectively. The correlation coefficient between left and right atrial pressure was 0.96, which represents the dynamic function of the interatrial shunt in controlling left-right imbalance of cardiac output. During pumping days, the temperature on the surface of actuator had been maintained at 39.7$\pm$0.4$^{\circ}C$, less than 1$^{\circ}C$ higher than the rectal temperature. The TAH stopped on the 11th day due to mechanical problems. We concluded that the EH-TAH possessed satisfactory basic performance including anatomic fit and hemodynamic adequacy, although there were several mechanical problems to be solved yet.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.53 no.2
• /
• pp.76-86
• /
• 2016

SQL Injection attacks are the most widely used and also they are considered one of the oldest traditional hacking techniques. SQL Injection attacks are getting quite complicated and they perform a high portion among web hacking. The big data environments in the future will be widely used resulting in many devices and sensors will be connected to the internet and the amount of data that flows among devices will be highly increased. The scale of damage caused by SQL Injection attacks would be even greater in the future. Besides, creating security solutions against SQL Injection attacks are high costs and time-consuming. In order to prevent SQL Injection attacks, we have to operate quickly and accurately according to this data analysis techniques. We utilized data analytics and machine learning techniques to defend against SQL Injection attacks and analyzed the execution plan of the SQL command input if there are abnormal patterns through checking the web log files. Herein, we propose a way to distinguish between normal and abnormal SQL commands. We have analyzed the value entered by the user in real time using the automated SQL Injection attacks tools. We have proved that it is possible to ensure an effective defense through analyzing the execution plan of the SQL command.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.22 no.3
• /
• pp.239-248
• /
• 2020

Exact rock classification helps suitable support patterns to be installed. Face mapping is usually conducted to classify the rock mass using RMR (Rock Mass Ration) or Q values. There have been several attempts to predict the grade of rock mass using mechanical data of jumbo drills or probe drills and photographs of excavation surfaces by using deep learning. However, they took long time, or had a limitation that it is impossible to grasp the rock grade in ahead of the tunnel surface. In this study, a method to predict the Q value ahead of excavation surface is developed using recurrent neural network (RNN) technique and it is compared with the Q values from face mapping for verification. Among Q values from over 4,600 tunnel faces, 70% of data was used for learning, and the rests were used for verification. Repeated learnings were performed in different number of learning and number of previous excavation surfaces utilized for learning. The coincidence between the predicted and actual Q values was compared with the root mean square error (RMSE). RMSE value from 600 times repeated learning with 2 prior excavation faces gives a lowest values. The results from this study can vary with the input data sets, the results can help to understand how the past ground conditions affect the future ground conditions and to predict the Q value ahead of the tunnel excavation face.

• Journal of agriculture & life science
• /
• v.45 no.4
• /
• pp.135-141
• /
• 2011

This research was conducted to provide basic data of surplus heat for designing solar heat-storage systems. The surplus heat is defined as the heat exhausted by forced ventilations from the greenhouses to control the greenhouse temperature within setting limits. Various simulations were performed to compare the differences of thermal behaviors among greenhouse types as well as among several domestic areas by using pseudo-TMY (Typical Meteorological Year) data manipulated based both on the weather data supplied from Korean Meteorological Administration and the TMY data supplied from The Korean Solar Energy Society. Additional analyses were carried out to examine the required heating energy together with some others such as the energy balances in greenhouses to be considered. The results of those researches are summarized as follows. Regional surplus solar heats for the nine regions with 4-type were analyzed. The results showed that the ratio of surplus solar energy compared to heating energy was the highest in Jeju (about 212.0~228.0%) for each greenhouse type. And followed by Busan, Kwangju, Jinju, Daegu, Daejeon, Jeonju, Suwon and Daekwanryung. And irrespective of greenhouse types, surplus solar energy alone could cover up nearly all of the required supplemental heating energy except for a few areas.