• 한국분말재료학회지
• /
• 제16권3호
• /
• pp.209-216
• /
• 2009

A composite of rapidly solidified Al-6061 alloy powder with graphite particle reinforcements was prepared by ball milling and subsequent hot extrusion. The microstructure and mechanical properties of these composites were investigated as a function of milling time. With increasing milling time, the gas atomized initially and spherical powders became elongated with a maximum aspect ratio after milling for 30 h. Then, refinement and spheroidization were achieved by further milling to 70 h with a homogeneous and fine dispersion of graphite particles forming between the matrix alloy layers. The best compression and wear properties were obtained in the powder milled for 70 h, associated with the increased fine and homogeneous distribution of graphite particles in the aluminum alloy matrix.

• 한국주조공학회지
• /
• 제18권6호
• /
• pp.550-554
• /
• 1998

The microstructures of rapidly solidified binary Ti-Al alloys containing $45{\sim}58\;at%Al$ have been studied using C/S (carbon/sulfur), N/O (nitrogen/oxygen) analyser, X-ray fluorescence spectrometer (XRF), X-ray diffractometer (XRD), optical microscope (OM) and scanning electron microscope (SEM). The phases present in the alloys and their distribution were found to be a sensitive function of Al content. Essentially single-phase (${\gamma}$) microstructures were observed to alloys with 45 at%Al, 55 at%Al and 58 at%Al. In other content alloys, two phase (${\alpha}_2$, ${\gamma}$) microstructures were observed. The 48 at%Al, 52 at%Al alloys contain (${\gamma}+{\alpha}_2$) phase and ${\alpha}_2$ phase. These results indicate that rapid solidification affect the solidification path, then metastable phase forming during solidification.

• 한국재료학회지
• /
• 제9권4호
• /
• pp.386-391
• /
• 1999

The charge-discharge, the high-rate dischargeability, and the self discharge characteristics of the electrodes composed of rapidly solidified ZrV\ulcornerMn\ulcornerMo\ulcornerNi\ulcorneralloy, which has the form of partial substitution of Mn, Mo, Ni for V in $ZrV_2$ were studied. The alloys were prepared using Arc & RSP(Rapid Solidification Process) at the rotating roller speed of 2000 and 5000 rpm. Some of them were received heat treatment at$ 560 ^{\circ}C$ for 1 hour after the solidification to investigate the effect of the heat treatment. It was fond that cycle life was significantly improved by RSP, whereas discharge capacity, activation rte and high rate dischargeability were decreased compared with the conventional arc melting method. The capacity loss seems to be due to the loss of the crystallinity and the increase of the cycle life ascribed to the presence of the amporphous phase as well as the refined grain size of less than 0.2$\mu\textrm{m}$. Heat treatment of the alloy cooled at 2000 rpm improved the cycle life. In case of the alloys cooled at 5000 rpm, both the discharge capacity and the activation rate were significantly improved by the heat treatment.

• 한국자기학회지
• /
• 제4권2호
• /
• pp.126-129
• /
• 1994

희토류원소 Pr의 첨가가 Fe-B계 비정질합금의 자왜에 미치는 영향을 조사하기 위하여 비정질 $Fe_{86-x}B_{14}Pr_{x}(2{\leq}x{\leq}8\;at.%)$ 합금을 급속응고법을 이용하여 제조하였다. 급 속응고상태 비정질 $Fe_{86-x}B_{14}Pr_{x}$ 합금의 포화자왜는 Pr이 증가할 수록 증가하여 x=8에 서 약 50 ppm이 얻어졌다. 특히 $300^{\circ}C$에서 2시간 열처리된 비정질 $Fe_{84}B_{14}Pr_{2}$ 합금의 포화자왜는 70 ppm으로 증가하였다. $300^{\circ}C$에서 2시간 열처리된 비정질 $Fe_{84}B_{14}Pr_{2}$ 합금의 교류 자기이력손실 및 교류투자율$(f=50\;kHz,\;B_{m}=0.1\;T)$은 각각 15 W/kg, $5.5{\times}10^{3}$이었다.

• 한국주조공학회지
• /
• 제8권4호
• /
• pp.453-458
• /
• 1988

Al-Si alloy powder produced by the gas atomizer showed fine eutectic structure between ${\alpha}-dendrites$, that was grown by coupled growth, and there remained small amount of ${\alpha}$ in Al - 20 wt% Si alloy. The morphology of Si in the eutectic structure was largely influenced by the recalescence caused by solidification latent heat, and that was thought to be due to decrement of the surface energy of Si. In modified eutectic Si by rapid solidification, fine twin about $0.01\;{\mu}m$ was observed and growth direction of eutectic Si was <112>. This fact implied that the growth mechanism of eutectic Si in rapid solidification was related to TPRE mechanism. Due to rapid solidification Si was soluble in ${\alpha}-phase$ in Al - 12.6wt%Si alloy up to about 3.4wt%, and the solubility of Si in ${\alpha}-phase$ reaches the equilibrium solubility stare after 60min, holding when it was held isothermally at $253-296^{\circ}C$.

• 한국자기학회지
• /
• 제3권2호
• /
• pp.135-138
• /
• 1993

Fe-B계 비정질합금에 Al을 치환한 $Fe_{82}B_{18-x}Al_{x}$ 및 $Fe_{80}B_{20-x}Al_{x}$급속응고합금의 포화자왜 인장응력에 의한 자기탄성효과가 조사되었다. 포화자왜는 Al 치환량이 증가 할수록 증가 하며, 비정질 $Fe_{82}B_{14}Al_{14}$합금에서 45 ppm으로 가장 높다. 비정질 $Fe_{82}B_{14}Al_{14}$ 합금의 인장응력에 따른 최대자속밀도의 변화율은 약 $0.026\;T.mm^{2}/N$으로 고분해능 역학센서로 응용이 가능할 것으로 예상된다.

• 한국주조공학회지
• /
• 제20권6호
• /
• pp.386-394
• /
• 2000

In the present study, the effect of yttrium addition on the microstructure and mechanical property of rapidly solidified AZ91 alloy by melt spinning process is estimated. As yttrium was added, the microstructure of RS ribbons and extrudates became finer than those of AZ91, and RE related phases $(Al_2RE)$ were formed. In the case of the addition of 3wt%Y, the microstructure of extrude showed the finest grain size. At room temperature, the AZ91 + 3wt%Y alloy showed the highest tensile strength, 352 MPA due to precipitation of ${\beta}(Mg_{17}Al_{12})$ phase and $Al_2RE$ phase. At the elevated temperature, the mechanical property of AZ91 + 3wt%Y alloy was higher than those of other Mg alloys. The reasons were that $Al_2Y$ compound was thermally stable and suppressed the grain growth. In contrast with $Al_2Y$ compounds, ${\beta}$ phase was thermally unstable and could not suppress the grain growth at the elevated temperature. Therefore, $Al_2Y$ phase contributed to improve the thermal stability of RS AZ91 alloy.

• 한국주조공학회지
• /
• 제28권4호
• /
• pp.184-189
• /
• 2008

Ag-Cd alloy has been widely used as an electrical contact material, since Ag-Cd alloy has a good wear resistance and stable contact resistance. But nowadays Ag-Cd alloy is not considered as electrical contact material any more due to detrimental effect on environments. Currently, active researches are being performed on ($Ag-SnO_2$ and $Ag-SnO_{2}-In_{2}O_{3}$) as an alternative solution which can fix the remaining environmental problems. However, $In_{2}O_{3}$ is relatively expensive and Ag-Sn alloy has low wear resistance. Our recent research results show that Ag-X%Zn-Y%Sn has similar physical and chemical properties. In the present study, so we tried to change and to optimize the Zn oxide content to over 6 wt% and Sn oxide content with 0.5, 1.0, 1.5 wt%. Results obtained from the experiments on the Ag-X%ZnO-Y%$SnO_2$ are discussed.

• Pediatric Infection and Vaccine
• /
• 제19권2호
• /
• pp.79-83
• /
• 2012

라이 증후군은 간부전을 동반하며 급속히 진행하는 뇌증으로, 인플루엔자와 수두 바이러스 등에 감염된 어린이에게 발병한다. 아스피린이 주된 원인 인자로 알려진 이후 소아에서 아스피린의 사용을 줄이면서 현재는 매우 드물게 보고 되고 있다. 저자들은 가와사키병 치료를 위해 정맥내 면역글로불린을 투여받고 아스피린을 복용하던 중 보챔, 강직, 활동량 저하, 식욕 저하, 처짐, 구토, 간수치 상승, 혈액 응고 장애와 고암모니아혈증으로 치료받은 5개월 여아를 보고하는 바이다.

• 한국분말재료학회지
• /
• 제7권1호
• /
• pp.12-18
• /
• 2000

Effects of the microstrucrure of rapidy solidified Al-Pb-Cu-Mg alloys on the wear investigated. In order to overcome the miscility gap between Al and pb under equilibrium conditions, both in the solid and the liquid states, the alloy were rapidy solidifies to produce them in a segregation-free condition. Although the Pb particles showed relatively fine dispersion in the Al matrix in all the alloys by this process. the Al-16Pb alloy was found to have the most favorable microstructure with discretre with discrete Pb particles of abount 0.5 ${\mu}$m in size. With the addition of Cu and Cu-Mg to Al-16Pb, cellular structures were newly formed; not seen in the binary Al-Pb alloy. Wear properties of the Al-Pb binary alloys measured as a function of the sliding speen, sliding distance, and applied load showed that the Al-16Pb alloy has the best wear resistance, as expected from the fine microstructural features in this alloy. The were resistance of the alloy containing Cu-and Cu-Mg was higher than that of the Al-16Pvb alloy, due to matrix strengthening by precipitation hardeing. The wear mechanism was identified by examining the traces and wear debris.