• Journal of the Korean Magnetics Society
• /
• v.7 no.4
• /
• pp.173-179
• /
• 1997

Change in phases, microstructures, and magnetic properties by the variation of quench rate and heat treatment were investigated for melt-spun $Fe_{77}Pr_{15}C_8$ ribbons. The amorphization of as-spun ribbons increased as the quench rate increased. As a result, the ribbon quenched at 40 m/s was almost entirely amorphous. Similarly to cast alloys, the primary phase in crystalline ribbons quenched at 10 m/s was $\alpha$-Fe followed by the secondary $Fe_{17}Pr_2C_x$. Crystalline phases were still dominant in the ribbon spun at 20 m/s, but in this case crystallization of $Fe_{17}Pr_2C_x$ was remarkable with a little suppression of $\alpha$-Fe. At 30 m/s an amorphous phase obviously dominated in the as-spun ribbons with small fraction of crystals. Therefore, substantial amount of hard magnetic $Fe_{14}Pr_2C$ was not obtained from the as-spun state but, as in cast alloys, produced only by a solid-state transformation. Within a few minutes fine grains of $Fe_{14}Pr_2C$ were easily obtained at relatively low temperature when the degree of amorphization of as-spun ribbons was higher. The grain size of $Fe_{14}Pr_2C$ was well less than 1${\mu}{\textrm}{m}$. The ribbons quenched at 20 or 30 m/s yielded higher coercivities after heat treatment.

• 한국신재생에너지학회:학술대회논문집
• /
• 2011.11a
• /
• pp.48-48
• /
• 2011

2010년 약 19.5 GWp 의 규모로 성장한 태양광 시장의 주요 소재는 실리콘을 이용한 태양전지이며, 고성능 및 고효율 태양전지 시장이 급성장 하였다. 이러한 고품질 태양전지에 사용되는 주요 원료인 9N 급 폴리실리콘은 2008년 4월 $265/kg 까지 상승하였으나, 점차 하향안정세에 있으며, 급속한 가격 경쟁을 통해 당분간 장기공급가가 50$/kg 이하로 하락할 것으로 전망된다. 이러한 실리콘 제조기술 중 가장 많이 사용되는 기술은 Trichloro-silane (TCS) 또는 Mono-silane (MS)를 사용하는 기상법인 일명 Siemens 공정이다. 이러한 기상법의 경우 12N 이상의 초고품질 실리콘 제조가 가능하나, 대규모의 설비투자(1억원/폴리실리콘 1톤)와 높은 에너지(120 kWh/kg)가 요구된다. 이에 최근 기상법이 아닌 야금학적인 정련법에 대한 기술이 개발되고 있으며, 이는 금속 실리콘을 슬래그 처리, 편석 분리, 응고 급랭, 전자빔, 플라즈마 등을 이용하여 정련하는 공정을 말한다. 야금학적 정련법은 순도 면에서 기상법에 비하여 낮은 단점이 있음에도 불구하고, 여러 장점들로 인해 활발히 연구되며 점차 실용화 되고 있는 매우 유용한 기술이다. 야금학적 정련법의 주요 장점은 기상법에 비해 약 25% 정도의 설비 투자비로 가능하고, 금속 실리콘을 직접 사용하며, 에너지 payback이 짧다. 또한, 산 및 염화실렌을 사용하지 않으므로 환경 문제를 적게 야기하고, 생산설비의 확장성도 매우 높다. 본 연구에서는 국내 규석광을 이용하여 일련의 정련 공정을 거쳐 고순도SG(Solar Grade)급 실리콘을 제조하고자 하였다. 실리콘 용융 환원로를 개발하고 순도를 높이기 위해 슬래그정련법을 이용하였으며, 생산된 3N 급의 금속 실리콘을 비기상법정련 방식인 일방향 응고와 플라즈마 정련 및 전자기유도 용해법을 이용하여 고순도의 실리콘을 제조하였다. 본 연구에서는 상업생산을 개시한 외국의 E사와 비교하여 산침출공정을 거치지 않으므로 실리콘회수율 및 환경부하 절감의 장점을 갖고 있으며 최종 순도 실리콘 6N 이상, 보론 함유량 0.2 ppm 이하를 달성하였으며, 기존 기상법 대비 약 20%의 전력 감소와 약 13%의 금속실리콘 원료 절감 효과가 있었다. 저가/고순도 SG급실리콘의 제조기술 개발은 향후 세계 태양광 시장에 대한 경쟁력을 확보하고, 시장 점유율 상승에 기여할 수 있으며, 산업 확대를 통한 주변 산업으로의 파급 효과가 매우 클 것으로 예상된다.

• Journal of the Korean Magnetics Society
• /
• v.4 no.3
• /
• pp.226-232
• /
• 1994

Rapidly solidified $SmFe_{7+x}M_{x}(M=Mo,\;V,\;Ti)$ compound were found to crystallize in the ${Sm(Fe,\;M)}_{7}$ based stable magnetic phase by introducing a second transition element into the Sm-Fe binary system. The ${Sm(Fe,\;M)}_{7}$ phase exhibits the highest Curie temperatuer ($T_{c}=355^{\circ}C$) ever Known in the Sm-Fe magnetic systems with a quite high intrinsic coercivity($_{i}H_{c}=3~6\;kOe $). The ${Sm(Fe,\;M)}_{7}$ phase remains stable even after annealing if once form during the rapid solidification. The primary reason for the high coercive force is due to the fine grain size($2000~8000\;{\AA}$)of the magnetic ${Sm(Fe,\;M)}_{7}$ matrix phase, and the enhanced Curie temperature is attributed to the extended solid-solubility of the additive transition elements in Fe matrix, which leads to volume expansion of the ${Sm(Fe,\;M)}_{7}$ cell causing an enhanced coupling constant of Fe atoms.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1991.11a
• /
• pp.34-37
• /
• 1991

Al계 베어링합금은 소착저항력등의 베어링특성이 우수하여 최근에 자동차의 엔진부품에 많이 사용되고 있다. Al계 베어링합금으로는 Al-Sn계, Al-Pb계, Al-Si계 합금이 개발되어 사용되어 왔다. Al-Si계 합금은 높은 강도, 우수한 부식성, 주조성이 향상되는 장점등을 갖고 있다. 또한 Al-Pb계 합금은 Pb가 고체윤활제로 작용하여 소착저항성이 높으며 가격도 저렴한 장점을 갖고 있다. Al과 Pb는 용융상태에서 넓은 용융간극을 갖어 중력편석을 일으키기 때문에 일반적인 주조방법으로 Al계 베어링합금을 제조할 수없다. 또한 Al에 Si이 첨가됨에 따라 높은 경도등의 기계적성질의 향상이 얻어지지만 Al 기지에 Si의 함량이 증가할 수록 편석이 심해져 조대한 Si-rich상이 미세조직에 존재하여 합금이 취약해지는 단점을 갖고 있다. 따라서 본 연구에서는 Al 기지에 Pb의 중력편석을 최소화하고 Al 기지에 조대한 Si-rich상이 생성되는 것을 막기 위하여 Al과 Pb가 공존하는 온도구역에서 높은 교반속도로 용탕을 강제교반하여 액상에서 Pb와 Si을 미세하게 분산시킨 후 수냉되는 동주형에서 급속응고시켜 Pb와 Si-rich 상이 균일하게 분포된 Al계 베어링합금을 제조하였다. 본 연구에서는 Pb의 양을 0%에서 35%까지 변화시켰으며, Si의 양을 0%에서 20%까지 변화시켜서 베어링합금을 제조하였으며, 강제교반속도는 500rpm에서 2500rpm 까지 변화시켜 베어링합금을 제조하였다.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.20 no.1
• /
• pp.86-91
• /
• 2007

Contact material is widely used as electrical parts. Ag-CdO has a good wear resistance and stable contact resistance. But the disadvantages of Ag-Cd alloy are coarse Cd oxides and harmful metal, Cd. Then Ag-Sn alloy that has stable and fine Sn oxide at high temperature has been developed. In order to investigate the effect of Te additional that affects the formation of the oxide layer on the surface and the formation of oxide in matrix Ag, we studied the microstructures and properties of Ag-Sn-In(-Te) material fabricated by rapid solidification process. The experimental procedure were melting using high frequency induction, melt spinning, and internal oxidation. Specimens were examined and analyzed by Transmission electron microscopy(TEM), energy dispersive X-ray spectroscopy(EDS) and Vickers hardness. As a result, internal oxidation was completed even at $600^{\circ}C$. Te forms coarse $In_{2}TeO_{6}$ phase and makes fine and well dispersed $SnO_{2}$ Phase. 0.3 wt% Te shows favorable properties.

• Journal of Korea Foundry Society
• /
• v.27 no.2
• /
• pp.72-76
• /
• 2007

Contact materials are widely used as electrical parts. Ag-Cd alloy has a good wear resistance and stable contact resistance. But the Cd exists as coarse oxide in alloy so it have an effect on mechanical properties badly. Moreover, the Cd is an injury material to environment. Nowadays, the use of Cd is strictly restricted. Because of these disadvantage, Ag-Sn-In alloy has been developed. In Ag-Sn-In alloy, the Sn : In ratio affects the internal oxidation properties, such as the formation of the oxide layer on the surface. In this work, we changed and optimized the Sn : In ratio variety for good internal oxidation properties. We have shown that a internal oxidation process did not fully completed when the Sn : In ratio is over 4 : 1 because of the Sn oxide layer at surface. The increase of In decelerates the formation of Sn oxide layer.

• Journal of Powder Materials
• /
• v.15 no.1
• /
• pp.31-36
• /
• 2008

In this study, the bottom-up powder metallurgy and the top-down severe plastic deformation (SPD) techniques for manufacturing bulk nanomaterials were combined in order to achieve both full density and grain refinement without grain growth of rapidly solidified Al-20 wt% Si alloy powders during consolidation processing. Continuous equal channel multi-angular processing (C-ECMAP) was proposed to improve low productivity of conventional ECAP, one of the most promising method in SPD. As a powder consolidation method, C-ECMAP was employed. A wide range of experimental studies were carried out for characterizing mechanical properties and microstructures of the ECMAP processed materials. It was found that effective properties of high strength and full density maintaining nanoscale microstructure are achieved. The proposed SPD processing of powder materials can be a good method to achieve fully density and nanostructured materials.

• Journal of Powder Materials
• /
• v.3 no.4
• /
• pp.246-252
• /
• 1996

$Bi_{2}Te_{3}-Sb_{2}Te_{3}$, $Bi_{2}Te_{3}-Bi_{2}Se_{3}$ solid solutions are of great interest as materials for thermoelectric energy conversion. One of the key technologies to ensure the efficiency of thermoelectric device is to obtain chemically homogeneous solid solutions. In this work, the new process with rapid solidification followed by hot pressing was investigated to produce homogeneous thermoelectric materials. Characteristics of the materials were examined with XRD, SEM, EPMA-line scan and bending test. Property variations of the materials were investigated as a function of variables, such as excess Te quantity and hot pressing temperature. Quenched ribbons are very brittle and consisted of homogeneous $Bi_{2}Te_{3}$, $Sb_{2}Te_{3}$ solid solutions. When the process parameters were optimized, the maximum figure of merit was 3.073$\times$$10^{-3}K^{-4}$. The bending strength of the material, hot pressed at 45$0^{\circ}C$, was 5.87 kgf/${mm}^2$.

• Journal of Powder Materials
• /
• v.3 no.4
• /
• pp.271-278
• /
• 1996

In this study, the effect of the transition elements on the microstructure and mechanical properties of rapidly solidified Al-Mg-X alloys was investigated. As a result of the rapid solidification processing, fine equiaxed grains with a mean diameter of 2 $\mu$m were observed in these alloys. Many fine particles were found to be distributed rather homogeneously throughout the matrix with relatively large particles occasionally at grain boundaries. The ultimate tensile strengths of Al-Mg-X alloys were found to decrease rather remarkably at 150 $^{\circ}C$ without the gain of the ductility at 150 $^{\circ}C$, which may result from segregation of $\beta$ ($Al_{3}Mg_{2}$) precipitates. Fine dimples were observed on the fracture surfaces for all alloy systems and the variation of the size and shape of dimples was not observed upon alloy systems. The ductility at 530 $^{\circ}C$ was found to be ~100%, suggesting that grain boundary sliding did not contribute to ductiliy despite he grain size stabilization. The absence of superplastic behavior may be associated with low boundary misorientation in rapidly solidified Al-Mg-X alloys.

• Journal of Powder Materials
• /
• v.10 no.1
• /
• pp.15-20
• /
• 2003

Hybrid $A1_2O_3-TiC$ ceramic particle reinforced 6061 and 5083 Al composite powders were prepared by the combination of twin rolling and stone mill crushing process, followed by consolidating processes of cold compaction, degassing and hot extrusion. The composite bar consists of lamellar structure of ceramic particle rich area and matrix area, in which the hybrid was decomposed into each TiC of about $3-4\mutextrm{m}$ and $AI_2O_3$ particles of about $1-2\mutextrm{m}$ in diameter. It also found that fine $Mg_2Si$ precipitates of about 30 nm were embedded in the matrix, which have grains of about 3 $\mutextrm{m}$. Higher UTS was measured at the 5083 composite bar compared to the conventionally fabricated composite, due to again refinement effect by the rapid solidification. No particle was shown to form in the interface between the matrix and reinforcement, whereas carbon was diffused into the matrix.