• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.10 no.2
• /
• pp.79-88
• /
• 2001

This paper suggests to predict the failure of helical gear extrusion die. The basic assumption that constitutes the frame-work for any combined stress failure theory is that failure is predicted to occur when the maximum value of stress becomes equal to or exceeds the value of the same modulus that produces failure in a simple uniaxial stress test using the same material. The stresses which were calculated to each critical points are applied maximum normal stress theory and distor-tion energy theory. The theroretical analysis and experimental results for Samanta process and New process dies were com-pared.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2007.10a
• /
• pp.289-292
• /
• 2007

To prevent the damage of glass lens molds and deterioration of glass lenses using in progressive GMP process, a thermal stress and a deformation of the glass lens molds at forming temperature should be considered in the design step. In this study, as a fundamental study to develop a multi cavity mold used in an aspheric glass lens molding, a heat transfer and a thermal stress analysis were carried out for the case of one cavity glass lens mold used in progressive GMP process. Finally, using analysis results, we estimated the thermal stress in a glass lens mold and predicted a modified height of guide ring that determines the forming height of a glass lens.

• Journal of the Korean Society for Precision Engineering
• /
• v.16 no.11
• /
• pp.166-173
• /
• 1999

Al forged parts are many cases with rib-web section which is difficult to manufacture precisely. Therefore, process conditions must be optimized for precision forging of Al alloys. In this study, various process parameters such as die design, lubricant, ram speed, forging temperature have been investigated using the experiment, upper bound theory and F.E.M. simulation to develop the precision forging technology for rib-web shape component. When lubricant is applied to both material and die, shear friction factor is 0.1 which shows best effect of lubricant. It is specific corner radius of die that minimized forging load regarding process conditions, especially according to the ratio of the width of rib and web. In conclusion, optimum corner radius is 2~3mm when the width of rib and web is 3mm and 20mm respectively.

• Journal of the Korean Society for Precision Engineering
• /
• v.10 no.2
• /
• pp.30-39
• /
• 1993

The study is concerned with the thermo-viscoplastic finite element analysis of nonisothermal hot container extrusion through conical dies. The problem is treated as a non-steady state incorporating the nonisothermal heat transfer analysis. The analysis of temperature distribution includes heat transfer though the boundary surface including conduction, convection and radiation. The analysis of heat transfer is decoupled with the analysis of deformation and the material interaction is considered through iteration procedure. The effect of important process parameters including die angle and extrusion ratio in the process is investigated. Due to the geometric feature for the container extrusion through conical dies, automatic remeshing is mandatory. Automatic remeshing is achieved by introducing the modular remeshing technique.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.36 no.3
• /
• pp.283-288
• /
• 2012

Ultra-high-strength steels (UHSSs) are widely used for lightweight automobile parts, and the control of springback is very important in sheet-metal forming. The object of this study is to verify the effects of multi-stage forming process parameters for U-channel-type automobile parts made of UHSS. Finite element analysis is carried out to predict the formability and springback. The main parameters considered for the multi-stage forming process are the die angle, die radius, and punch-forming direction. It is shown that multi-stage forming is very effective for reducing springback, and that a small punch-forming angle and die radius reduce springback, whereas the die angle does not have a large effect.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.10
• /
• pp.115-120
• /
• 2018

This study examined the cast quality of small-sized induction motor rotors during the die casting process. Numerical analyses with 3-dimensional half models were performed to investigate the filling patterns of aluminum molten metals into a mold after high-speed injections. The following were obtained from numerical analyses and experimental results. First, molten metals started to fill the lower end ring, then moved horizontally to fill the core slot and upper end ring, and finally stopped to fill the rotor core slot. Second, circulation of molten metals occurred at the lower end ring, resulting considerable porosity at the section of lower end ring from the experimental results. Third, further work for obtaining sound quality of rotor core cast is required to develop a new shape of the rotor core cast or improve the die casting conditions.

• Journal of Advanced Marine Engineering and Technology
• /
• v.40 no.4
• /
• pp.314-319
• /
• 2016

Flange bolt has a circular flange under the head that acts like a washer to distribute the clamping load over a large area. Flange bolt has usually been manufactured by cold forging. Flower shape defect occurs in the flange forging stage. This defect causes lack of dimensional accuracy and low quality. So it is needed to improve these forging defects. In this study, die design method for flower shape defect of flange bolt was suggested. In order to improve flower shape defect, inner diameter of the addition die in conventional forging process was modified. The forging process with applied modified die was simulated by commercial FEM code DEFORM-3D. The simulated results for modified die were confirmed by experimental trials with the same condition.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.35 no.12
• /
• pp.1635-1640
• /
• 2011

The objective of this study is to design of a cooling system of the over-molding mold for a socket component of an automobile wiper by performing numerical analyses. Hot spots in which the temperature distributions are higher than those of other region, were estimated by an initial over-molding analysis for the initial design of the mold. On the basis of the initial over-molding analysis, two types of cooling system designs with a linear cooling channel and a volumetric heat sink, were considered to improve the cooling characteristics of hot spots. To obtain an appropriate cooling system design, the effects of the diameter and the position of the linear cooling channels on the cooling characteristics and the product qualities were quantitatively examined. In addition, the effects of the design of the volumetric heat sink on the cooling characteristics and deformation distributions in the molded product were investigated. The results of the over-molding analysis of the two types of cooling systems showed that the multi-sliced over-molding mold with a volumetric heat sink can improve both the product quality and the cooling characteristics of the mold.

• Proceedings of the KAIS Fall Conference
• /
• 2009.12a
• /
• pp.678-681
• /
• 2009

사출성형은 열가소성수지의 가공법으로써 정밀도나 고품질의 제품을 효과적으로 생산하는데 널리 이용되며 플라스틱은 현재 광범위하게 사용되고 있는 공업재료 중의 하나이다. 과거에는 플라스틱을 일회용품 및 외장재로 사용하였다. 그러나 산업기술이 발전하며 플라스틱은 금속을 대체 할 수 있는 재료로서 사용할 수 있다는 인식의 변화로 점차 기계요소용 재료로 사용되고 있으며 기계요소용 재료로 사용됨에 따라 플라스틱 제품이 정밀한 부품으로 사용되기 위해서는 금형의 가공뿐만 아니라 사출성형 시 용융수지가 금형의 각 캐비티에 균형적으로 충전되는것이 요구된다. 이러한 요구조건을 만족하기 위해서는 각 캐비티의 가공치수는 매우 높은 정밀도를 유지해야 하며, 각 캐비티에서의 충전과 냉각도 동일한 상태를 유지해야 한다. 충전 불균형은 성형품의 품질에 큰 저해 요인으로서 플라스틱 제품의 치수성, 밀도, 외관품질, 강도 등에 불균일한 결과를 가져오는 요인으로 지적되고 있다. 실제로 충전 불균형은 충전 단계에서 런너 내에서 발생하는 불균일한 전단분포에 기인하여 발생되므로 점도변화에 영향을 주는 수지의 물성, 런너의 배열과 같은 외부 요인과 사출압력, 사출속도, 수지온도, 금형온도와 같은 성형공정 조건에 의한 요인에 의한 충전 불균형의 양상이 달라지게 된다. 본 연구는 다수 캐비티 금형에서 충전 불균형 현상에 대한 원인을 검토하고 실제로 사출성형을 실시하기 전 사출성형해석 소프트웨어를 이용하여 시뮬레이션을 하여 다수 캐비티에 대한 충전 패턴을 미리 예측하여 보았다.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.12 no.2
• /
• pp.588-593
• /
• 2011

For the progressive notching and forming die, analyzing beforehand according to the interpretation of thin plate molding for massive production is essential. In this study, we dealt with Ez5 particularly its strip layout design based on the exported die as ordered by Japanese S automobile company's local factory in the USA. We completed the strip layout design consisting of 13 processes by optimizing the blank layout with arrays of a single carrier with wide width drawn in 1 row. This type of die is expected to be ordered in bulk frequently and at the same time via the Internet; any company with die technology will be required to cope with such type of die.