• Applied Chemistry for Engineering
• /
• v.9 no.3
• /
• pp.348-354
• /
• 1998

Cellulose grafted with acrylic acid(AAc) was prepared by radiation grafting technique. The effects of reaction temperature. reaction time, monomer concentration, and the crosslinkers on the AAc grafting reaction on cellulose were examined. The amount of AAc grafted on the cellulose reached maximum at the concentration of 0.75vol% difunctional crosslinker and 1.0vol% trifunctional crosslinker, respectively. In the presence of acid, the amount of AAc grafted on the cellulose was decreased when reaction solution contains difunctional crosslinker, while that was increased when reaction solution contains trifunctional crosslinker. In the grafting reaction of cellulose with AAc and TMETA, mixture containing ferrous sulfate and acid enhanced further AAc grafting yield than mixture containing ferrous sulfate only.

• Journal of Sericultural and Entomological Science
• /
• v.27 no.1
• /
• pp.47-50
• /
• 1985

The physical properties of graft polymerized silk fibre were investigated with various vinyl monomers. 1. The graft polymerization of styrene and methyl methacrylate onto raw silk reduced the tenacity and elongation of raw silk due to fixation of sericin covering silk fibre in, but the styrene grafting was more effective for sericin fixation of raw silk than the methyl methacrylate one. 2. The water absorbability of glycidyl methacrylate grafted silk increased 14.6% greater than that of methyl methacrylate grafted silk at the same degree of grafting polymerization. 3. The degree of grafting polymerization was increased mostly with ethylene glycol methacrylate. The water absorbability of ethylene glycol methacrylate grafted silk was higher than that of glycidyl methacrylate or ethyl acrylate grafted silk. But the grafted silk fabric increased the fabric flexural rigidity which was negatively related with the favorability of fabric hand-touch, as compared with that of nongrafted silk fabric. 4. The evenness of graft polymerization could be improved by agitating the polymerization bath at the fixed interval by reducing the inter size deviation of grafted silk skein and the thickness deviation of grafted silk fabric.

• Journal of Adhesion and Interface
• /
• v.2 no.4
• /
• pp.10-23
• /
• 2001

In order to increase the lower values of % grafting and monomer conversion in the emulsion graft polymerization of methylmethacrylate(MMA) onto sodium alginate (SA; a polymer electrolyte) with alginic acid-g-PMMA, the graft polymerization with water soluble (methanol and acetone) and insoluble solvents was carried out using a varity of solvent amounts and agitating rates. And some physical properties of the graft polymer were also investigated. In the polymerizations with water insoluble solvent, there were pronounced improvements in both % grafting and MMA conversion by the promotion of MMA diffusion from the core to the SA adsorpted on the outer layer of particle and that of MMA complex formation with SA. And the effect was larger for the solvents (cyclohexane, decalin) which do not dissolve PMMA. On the other hand, in the polymerization with water soluble solvent, there was an significant increase in MMA conversion and a considerable increase in the % grafting by the destruction of electrical double layer around the SA chains, abstracting the hydrated water in the layer and the effect was more potential in the case of methanol which is a precipitant of PMMA.

• Elastomers and Composites
• /
• v.33 no.5
• /
• pp.363-369
• /
• 1998

Photografting reaction onto styrene-butadiene rubber (SBR) as a function of monomer concentration, irradiation time and carbon black content has been studied using ultraviolet (UV). Acrylamide and benzophenone are used as monomer and photoinitiator, respectively. FT-IR ATR and static contact angle analysis using distilled water are used to measure the graft ratio of acrylamide onto SBR surface. Graft ratio of acrylamide increases with acrylamide concentration and irradiation time and contact angle tends to decrease with increasing graft ratio. It is observed that graft ratio increases with carbon black content.

• Applied Chemistry for Engineering
• /
• v.7 no.5
• /
• pp.938-945
• /
• 1996

The present studies are to describe the grafting reaction of styrene in various solvents to polypropylene fabric by the simultaneous method using Co-60. The influence of various factors such as absorbed dose, dose rate, type of solvent, acid and multifunctional monomer were evaluated. At constant absorbed dose, the grafting yield was found to be higher at low dose rate. The initial rate of grafting was found to be proportional to a 0.56 power of dose rate. The inclusion of mineral acid in the grafting solution led to an increase in radiation grafting yield at almost all monomer concentration examined. Multifunctional monomer was also effective to increase grafting yield. The addition of both acid and multifunctional monomer was found to accelerate the grafting yield much more than the separate addition of two additives.

• Applied Chemistry for Engineering
• /
• v.3 no.3
• /
• pp.491-498
• /
• 1992

Graft polymerization of 2-hydroxyethyl methacrylate(HEMA) and styrene, from both their binary and unitary systems, onto polytetrafluoroethylene(PTFE) film was investigated by means of the simultaneous ${\gamma}-ray$ induced method. The effect of various parameters such as monomer concentration, dose rate, absorbed dose, HEMA/styrene feed ratios and the type of diluent on the extent of grafting in unitary and binary systems was studied. It was observed that when unitary HEMA was used for grafting, the grafting extent was very slight, whereas when comonomers were used, a good grafting yield could be obtained. Inclusion of sulfuric acid in the monomer solution resulted in enhanced grafting yields.

• Applied Chemistry for Engineering
• /
• v.7 no.5
• /
• pp.946-953
• /
• 1996

The effect of absorbed dose, dose rate, cationic salts and solvent on the grafting yield was evaluated when acrylic acid was grafted onto polypropylene fabric by simultaneous irradiation process. Low dose rate when irradiated with the same absorbed dose led to a high grafting yield. On the other hand, the grafting yield increased with dose rate in case the total irradiation times is equal, and the initial rate of grafting was found to be proportional to be 0.74 power of dose rate. $FeSO_4{\cdot}7H_2O$ was found to be the most effective additive for high grafting yield, while inhibiting homopolymer formation. It was impossible to induce radiation grafting without the addition of the certain amount of salt, but the grafting yield decreased with increasing metallic salt.

• Applied Chemistry for Engineering
• /
• v.10 no.6
• /
• pp.954-959
• /
• 1999

Radiation-induced grafting of 2-hydroxyethyl methacrylate(HEMA), acrylic acid(AAc) and methacrylic acid(MAAc) onto polypropylene microfiltration membrane has been studied. The effect of grafting conditions such as solvent composition(MeOH and $H_2O$) and monomer concentration on the grafting yield in investigated. The highest degree of grafting is obtained at a solvent composition of 25% $H_2O$:75% MeOH for HEMA, pure water for AAc and 50% $H_2O$:50% MeOH for MAAc. Modification of the PP membranes with hydrophilic monomers is shown to cause an increase in the water permeation flux of the membranes. It is found that HEMA is the best monomer to increase the water permeation flux and the highest water permeation flux is obtained at 99% degree of grafting. The water permeation flux of AAc-grafted PP membrane and MAAc-grafted PP membrane is very sensitive to environmental pH and $Cu^{2+}$ ion, but the water permeation flux of HEMA-grafted PP membrane scarcely depends on pH and $Cu^{2+}$ ion.

• Clean Technology
• /
• v.19 no.4
• /
• pp.393-400
• /
• 2013

In this study, Polyethylene wax, which was produced in manufacturing process of high density polyethylene was grafted with maleic anhydride (MAH). The influences of reaction parameters on the graft polymerization as well as the effect of hydrolysis of the anhydride functions were investigated. The results show that the grafting degree increased and conversion of maleic anhydride decreased with an increase in MAH monomer content. This means the highest grafting efficiency for the reaction can be met when MAH monomer content is about 15 wt%. DCP (dicumyl peroxide) and DTBP (di-tert-butyl peroxide) have been used as the initiator and the highest yield of grafting was obtained when the initiator content is about 0.5 wt%. However, It can be seen that the gel content values of this polyethylene wax grafted MAH were below 2%. It was also observed that the grafting degree increased with an increase in reaction temperature and the maximum value was reached 2 hours later. Although MAH functions grafted onto polyethylene wax were mainly in the carboxylic acid forms, some anhydride form of MAH appeared in over 5% of grafting degree. As a result of hydrolysis reaction, it was observed that the conversion of anhydride group into carboxylic acid group was reached up to 10%.

• Applied Chemistry for Engineering
• /
• v.5 no.3
• /
• pp.395-405
• /
• 1994

The various functional groups, such as hydroxyl(-OH), carboxyl(-COOH) and quinonic oxygen(OC<) on the carbon black(abbreviated to CB) surface were activated with n-butyl lithium solution in n-hexane and then acrylate and methacrylate monomers were graft polymerized onto these activated anionic sites and CB-grafted polymers were obtained. To separate homopolymers from reaction mixture, non-solvent precipitation method or centrifugal separating method were applied. Subsequently, conversion, grafting ratio and efficiency were determined at various reaction temperatures and times. In case of acrylates, the grafting ratio showed 20~30% but methacrylates showed 150~200%. Also the anion polymerizations between CB and monomers were nearly reached to equilibrium state within one or two hours under each reaction temperatures but conversion and grafting ratio were increased a little with reaction temperature increase. In colloidal dispersion stability test, before heat-drying, the all CB-grafted polymers showed good dispersed stability in good solvents for acrylic and methacrylic homopolymers. Futhermore, CB-polymethacrylates were found to show excellent collidal properties for good solvents of methacrylic homopolymer even after heat-drying. Identification of the grafted polyacrylates and polymethacrylates onto the CB surface was performed by FT-IR spectroscopy. In addition, electric resistance values of CB-grafted polymers were measured by Four-probe method, and the increase of the grafting ratio showed the increase of the surface resistance.