• Korean Journal of Mineralogy and Petrology
• /
• v.33 no.2
• /
• pp.99-114
• /
• 2020

The characteristics of the Brazilian tensile strengths(σ_t) parallel to the rock cleavages in Jurassic granite from Geochang were analysed. The evaluation for the six directions of rock cleavages was performed using the parameter values on microcrack length and the above strength. The strength values of the five test specimens belonging to each direction were classified into five groups. The strength values of these five groups increase in order of group A < B < C < D < E. The close dependence between the above microcrack and strength was derived. The analysis results of this study are summarized as follows. First, the chart showing the variation and characteristics of strength among the three rock cleavages were made. In the above chart, the strength values of six directions belonging to each group were arranged in order of rift(R1 and R2), grain(G1 and G2) and hardway(H1 and H2). The strength distribution lines of the five groups concentrate in the direction of R1. And the widths among the above five lines indicating strength difference(Δσ_t) are the most narrowest in R1 direction. From the related chart, the variation characteristics among the two directions forming each rock cleavage were derived. G2(2)-test specimen shows higher value and lower value of the difference in strength compared to the case of G1(1)-test specimen. These kinds of phenomena are the same as the case between the test specimen H2(2) and H1(1). The strength characteristics of the above test specimens (2) suggest lower microcrack density value and higher degree of uniformity in the distribution of microcracks arrayed parallel to the loading direction compared to those of test specimens (1). The six strength values belonging to each group were arranged in increasing order in the above chart. The strength values of the test specimens belonging to both group D and E appear in order of R1 < R2 < G1 < H1 < G2 < H2. Therefore, the strength values of group D and E can be indicator values for evaluating the six directions of rock cleavages. Second, the correlation chart between slope angle(θ) and strength difference(Δσ_t) were made. The values of the above two parameters were obtained from the five strength distribution lines connecting between the two directions. From the chart related to rift plane(G1-H1, R'), grain plane(R1-H2, G') and hardway plane(R2-G2, H'), the slope values of linear functions increase in order of R'(0.391) < G'(0.470) < H'(0.485). Among three planes, the charts related to hardway plane show the highest distribution density among the five groups. From the related chart for rift(R1-R2, R), grain(G1-G2, G) and hardway(H1-H2, H), the slope values of linear functions increase in order of rift(0.407) < hardway(0.453) < grain(0.460). Among three rock cleavages, the charts related to rift show the highest frequency of groups belonging to the lower region. Taken together, the width of distribution of the slope angle among the three planes and three rock cleavages increase in order of H' < G < R' < R < G' < H. Third, the correlation analysis among the parameters related to microcrack length and the tensile strengths was performed. These parameters may include frequency(N), total length(Lt), mean length(Lm), median length(Lmed) and density(ρ). The correlation charts among individual parameters on the above microcrack(X) and corresponding five levels of tensile strengths for the five groups(Y) were made. From the five kinds of correlation charts, the values of correlation coefficients(R²) increase along with the five levels of strengths. The mean values of the five correlation coefficients from each chart increase in order of 0.22(N) < 0.34(Lt) < 0.38(ρ) < 0.57(Lmed) < 0.58(Lm). Fourth, the correlation chart among the corresponding maximum strength for group E(X) and the above five parameters(Y) were made. From the related chart, the values of correlation coefficient increase in order of 0.61(N) < 0.81(Lt) < 0.87(ρ) < 0.93(Lm) < 0.96(Lmed). The two parameters that have the highest correlations are median length with maximum strength. Through the above correlation analysis between microcrack and strength, the credibility for the results from this study can be enhanced.

• The Journal of Korean Academy of Prosthodontics
• /
• v.48 no.3
• /
• pp.194-201
• /
• 2010

Purpose: The purpose was to compare the marginal fidelity and the fracture resistance of the zirconia crowns according to the various coping designs with different thicknesses and cement types. Materials and methods: Zirconia copings were designed and fabricated with various thicknesses using the CAD/CAM system (Everest, KaVo Dental GmbH, Biberach., Germany). Eighty zirconia copings were divided into 4 groups (Group I: even 0.3 mm thickness, Group II: 0.3 mm thickness on the buccal surface and the buccal half of occlusal surface and the 0.6 mm thickness on the lingual surface and the lingual half of occlusal surface, Group III: even 0.6 mm thickness, Group IV: 0.6 mm thickness on the buccal surface and the buccal half of occlusal surface and the 1.0 mm thickness on the lingual surface and the lingual half of occlusal surface) of 20. By using a putty index, zirconia crowns with the same size and contour were fabricated. Each group was divided into two subgroups by type of cement: Cavitec$^{(R)}$ (Kerr Co, USA) and Panavia-$F^{(R)}$ (Kuraray Medical Inc, Japan). After the cementation of the crowns with a static load compressor, the marginal fidelity of the zirconia crowns were measured at margins on the buccal, lingual, mesial and distal surfaces, using a microscope of microhardness tester (Matsuzawa, MXT-70, Japan, ${\times}100$). The fracture resistance of each crown was measured using a universal testing machine (Z020, Zwick, Germany) at a crosshead speed of 1 mm/min. The results were analyzed statistically by the two-way ANOVA and oneway ANOVA and Duncan's multiple range test at $\alpha$=.05. Results: Group I and III showed the smallest marginal fidelity, while group II demonstrated the largest value in Cavitec$^{(R)}$ subgroup (P<.05). For fracture resistance, group III and IV were significantly higher than group I and II in Cavitec$^{(R)}$ subgroup (P<.05). The fracture resistances of Panavia-$F^{(R)}$ subgroup were not significantly different among the groups (P>.05). Panavia-$F^{(R)}$ subgroup showed significantly higher fracture resistance than Cavitec$^{(R)}$ subgroup in group I and II (P<.05). Conclusion: Within the limitation of this study, considering fracture resistance or marginal fidelity and esthetics, a functional ceramic substructure design of the coping with slim visible surface can be used for esthetic purposes, or a thick invisible surface to support the veneering ceramic can be used depending on the priority.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.57 no.3
• /
• pp.219-225
• /
• 2012

Seed size has been considered as an effective criteria for selection of the most vigorous seeds in sorghum [(Sorghum bicolor (L) Moench]. The smaller seeds were inferior to the larger sizes in emergence and grain yield. This study was conducted to determine germination rate, field emergence and vigor of sorghum for selection of high quality seed by different seed size. Sorghum cultivar of two (Hwanggeumchal and Tojong) were separated into five seed size proportion (<2.36, 2.80, 3.15, 3.35 and >3.55 mm diam.) according to seed size. The larger seed was more higher 1,000 seeds weight, seed density, carbohydrates and protein content. Total seed germination performing varied 92% at the largest size (>3.55 mm diam.) frequently inferior to slightly 67% at smaller seed (2.36 to 2.80 mm diam.) in the standard germination test. Seed size did have a significant effect on mean emergence time (MET) and maximum emergence rate index (ERI) and percentage of emergence. It should be noted that the results refer to MET of sorghum seeds ranging from 4.26 to 4.74 days. The relationship of seed size was not only to stand establishment but to grain yield. Yield was most affected by seed size and large seeds were superior to the smaller seed in 25~37% of the cases. Especially, yield was significant under 3.15 mm the beginning.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.42 no.4
• /
• pp.410-415
• /
• 1997

To investigate the flowering and pod setting characteristics of peanut, Dae-kwangtangkong and Shinnamkwangtangkong were planted on April 20 and May 10 in 1994 at National Honam Agricultural Experiment Station. Number of days from planting to the maximum flowering in Daekwangtangkong were shorter than those of Shinnamkwangtangkong by 6 days in April 20 planting and by 13 days in May 10 planting. Flowering durations of Daekwangtangkong and Shinnamkwangtangkong in April 10 planting were 73 and 71 days, respectively, while those of both varieties were 64 days in May 10 planting. The rates of matured pods on cotyledonary, primary or secondary, and third branches were 58∼78, 6∼15 and 0∼2％, respectively. The rates of effective flowers in Daekwantangkong and Shinnamkwangtangkong were 10％ and 8％, respectively, in April 20 planting. The rates of matured pods were 100％ in Daekwangtangkong and 97％ in Shinnamkwangtangkong when pods were set within 15 days after the initial flowering, while the rate was decreased markedly when pods were set later than 35 days after the initial flowering.

• Journal of the Korean Vacuum Society
• /
• v.18 no.2
• /
• pp.108-115
• /
• 2009

The superlattice infrared photodetector (SLIP) with an active layer of 8/8-ML InAs/GaSb type-II strained-layer superlattice (SLS) of 150 periods was grown by MBE technique, and the proto-type discrete device was defined with an aperture of $200-{\mu}m$ diameter. The contrast profile of the transmission electron microscope (TEM) image and the satellite peak in the x-ray diffraction (XRD) rocking curve show that the SLS active layer keeps abrupt interfaces with a uniform thickness and a periodic strain. The wavelength and the bias-voltage dependences of responsivity (R) and detectivity ($D^*$) measured by a blackbody radiation source give that the cutoff wavelength is ${\sim}5{\mu}m$, and the maximum Rand $D^*$ ($\lambda=3.25{\mu}m$) are ${\sim}10^3mA/W$ (-0.6 V/13 K) and ${\sim}10^9cm.Hz^{1/2}/W$ (0 V/13 K), respectively. The activation energy of 275 meV analyzed from the temperature dependent responsivity is in good agreement with the energy difference between two SLS subblevels of conduction and valence bands (HH1-C) involving in the photoresponse process.

• KSBB Journal
• /
• v.14 no.1
• /
• pp.114-118
• /
• 1999

In order to use a polysaccharide, curdlan, as a concrete admixture, we first developed a pilot-scale fermentation process for the mass production of curdlan. We also examined the rheological properties of curdlan, and tested how well the curdlan obtained in this work increased the segregational resistance of the cement slurry. Fermentation was performed in a 300-liter fermenter equipped with 3 disk-turbine impellers. Since curdlan production is stimulated under nitrogen-limiting conditions, the culture pH was shifted from the optimal pH for cell growth (pH 7.0) to the optimal pH for curdlan production (pH 5.5) at the onset of ammonium exhaustion. We obtained a curdlan production of 65 g/L in 120 hr batch cultivation of Agrobacterium species. The insoluble curdlan at the final stage of fermentation was readily harvested by centrifugation together with the cells. The freeze-dried sample contained 78% (w/w) of curdlan. The solubility and viscosity of the curdlan increased with the increase of the solution pH, which enhances the viscosity of concrete since the pH of concrete is extremely high (pH 13.0). Test results of the curdlan as a concrete admixture with cement slurry demonstrated that it prohibits the leakage of water. In conclusion, this work certifies and enlarges curdlan's industrial potential as a concrete admixture.

• Horticultural Science & Technology
• /
• v.17 no.3
• /
• pp.329-332
• /
• 1999

The objective of this study was to determine the influence of grafting timing, rootstock cut timing and leaf removal with promalin ($GA_{4+7}+BA$) treatments on the maiden tree growth, lateral development and flower bud initiation. In mid-March 1997, two-year-old M.9-T337 rootstocks selected with trunk diameter over 1 cm were planted in the field. Chip budding with 'Fuji' scion on M.9-T337 rootstock budded in mid-April was earlier in sprouting than chip budding in mid-June. Late cutting chip budding (LCCB) with 'Fuji' scion on M.9-T337 rootstock was lower in the failed budding percentage with 14% than that of early cutting chip budding (ECCB). Especially, ECCB in April was not suitable for scion growth such as uniformity with high percentage of failed tree. Grafting timing in mid-June and rootstock cutting timing of LCCB induced more branches and flower buds than other treatments. Removal of 8 to 10 uppermost immature leaves on central leader stem and application of Promalin 250 mg/L after every 30 cm of terminal growth produced a 189 cm tall tree with 9 flower buds and 14.2 short lateral shoot from 30 to 35 cm long in length in 1998. Promalin increased branching on second-season growth and, when combined with leaf removal, resulted in uniform distribution of branches along the central leader stem.

• Food Science and Preservation
• /
• v.15 no.6
• /
• pp.847-851
• /
• 2008

The handling and processing of agricultural products in Korea is done manually. Small plastic boxes, nets, and corrugated cardboard boxes are used as containers during harvesting, sorting and other product handling operations. However, these practices are labor-intensive, time-consuming, require various kinds of packing materials, and are expensive because of high operating costs. To overcome these problems, the use of pallet bins with pre-cooling and storage features for handling and processing bulk farm products was investigated. The airflow resistances through bulk potato, onion and mandarin stocks were measured, and the pallet bins and a pressure pre-cooling device were manufactured. The opening ratio, bed depth and airflow rate through bulk potato, onion and mandarin in the pallet bin were defined with regression equations. The cooling rates of bulk potato, onion and mandarin were 0.8C/h ($21.7{\rightarrow}0C$, 14.5 h), 0.4C/h ($15.4{\rightarrow}.0C$, 32.2 h) and 0.7C/h ($13.7{\rightarrow}C$, 18.8 h), respectively, with the pressure pre-cooling system. Temperature deviances for storage of bulk potato, onion and mandarin were 0.12C, 0.12C and 0.17C, respectively.

• International Journal of Highway Engineering
• /
• v.8 no.1 s.27
• /
• pp.1-13
• /
• 2006

This paper is one of the studies for developing new methodologies for improving performance of hot-mix recycled asphalt mixtures. The objective of this study is to evaluate rut-resistance characteristics of recycled asphalt mixture which was prepared by newly developed mixing method. The new mixing method provided more sufficient rejuvenation of old binder of reclaimed asphalt pavement (RAP), making homogeneous binder viscosity level in a recycled mixture. Two aggregates (gneiss and granite), two RAP contents (15% and 30%) and two contents (none and 6%) of polymer modifier (LDPE) were used. Recycled mixture was prepared with two methods; method A and method F. To examine difference of binder oxidation level by type of material within a recycled mixture, Gel-permeation chromatography(GPC) analysis was performed on the binders mixed with coarse aggregates and matrix separately. Laboratory tests were performed for evaluation of rut resistance characteristics of each recycled mixture and these includes wheel tracking (WT) test and Kim test. Rut depth and dynamic stability were obtained from WT test and deformation strength $(S_D)$ was obtained from Kim test. The results of regression analysis was shown that correlation $(R^2)$ of F mixing mixtures was higher than one of A mixing mixtures. Therefore, F mixing mixtures showed more consistent rut resistance than h mixing mixtures.

• Journal of Bio-Environment Control
• /
• v.5 no.2
• /
• pp.187-193
• /
• 1996

This experiment was conducted to investigate the influence of temperature variation by the different ventilation methods on the growth and quality of oriental melon in greenhouse of tunnel type 1. The dropping effect in temperature by ventilation types was best at type 3 and those of type 2, type 1 were in order. 2. The temperature distribution in type 3 was uniformed as air- inflow and air- outflow by wind ventilation were easier than others. Whereas the temperature of type 1 having lateral ventilation hole and type 2 having the zenith ventilation tube and lateral ventilation hole was ascended, because small ventilation area of ventilation tube and hole could not make the gravity and wind ventilation successfully. 3. When compared with air amount of three types ventilated by the temperature difference of outside and inside of tunnel type house, that of type 3 was more than those of type 1 and type 2. 4. Type 3 was better than type 2 and type 1 in lear numbers, leaf area, fruit weight, flesh thickness, malformed fruit rate, and marketable fruit rate. 5. Marketable fruit rate of all treatment at each harvesting stages was rised, as goes to the latter periods.