• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.16 no.5
• /
• pp.72-84
• /
• 2017

Together with the Big Data of the 4th Industrial Revolution, the traffic information system has been changed to an section detection system by the point detection system. With DTG(Digital Tachograph) data based on Global Navigation Satellite System, the properties of raw data and data according to processing step were examined. We identified the vehicle trajectory, the link travel time of individual vehicle, and the link average travel time which are generated according to the processing step. In this paper, we proposed a application method for traffic management as characteristics of processing data. We selected the historical data considering the data management status of the center and the availability at the present time. We proposed a method to generate the Travel Time Index with historical link average travel time which can be collected all the time with wide range. We propose a method to monitor the traffic congestion using the Travel Time Index, and analyze the case of intersections when the traffic operation method changed. At the same time, the current situation which makes it difficult to fully utilize DTG data are suggested as limitations.

• Proceedings of the KWS Conference
• /
• 2009.11a
• /
• pp.121-121
• /
• 2009

자동차는 코너 주행 시 In-corner와 Out-corner 의 바퀴 궤적이 달라지므로, 특별한 장치가 없이 좌우 구동 측의 바퀴가 같은 속도로 회전을 하게 되면 정상적인 주행이 불가능하다. 따라서 정상적인 코너 주행이 가능 하려면, 코너 안쪽 바퀴보다 바깥쪽 바퀴가 더 빨리 회전해야 하며 이러한 회전 차를 보상받지 못할 경우 바깥쪽 바퀴가 끌리는 현상이 발생하는데 이를 방지하기 위해 디퍼렌셜 기어가 필요하다. 현재 디퍼렌셜 기어는 디퍼렌셜 케이스와 링기어를 볼트로 체결하는 조립 공법을 통해 생산되고 있다. 하지만 볼트 체결 공법은 조립을 위한 볼트와 볼트 체결을 위한 플랜지와 볼팅을 위한 홀을 가공하는 공정이 필요하기 때문에 재료비 절감 및 생산 효율 향상에 매우 불리하고 볼트체결을 위한 부분 때문에 불필요한 무게가 증가하게 된다. 따라서 본 연구에서는 이러한 기계적 체결 방식을 레이저 용접 방식으로 대체하여 재료비를 절감하고 무게 저감을 통해 주행성능을 향상시키고자 하였다. 링기어의 소재는 침탄처리강(SCM420H)이며 디퍼렌셜 케이스의 소재는 주철(GCD500)을 사용하고 있다. 주철은 용접시 용접부와 열영향부에서 마르텐사이트 조직과 레데브라이트, 시멘타이트 조직이 생성되며 고탄소 모재의 탄소 확산으로 인한 부분 혼합영역에서 탄소 합금이 생성되어 균열이 발생하는 등 용접성이 매우 좋지 않은 것으로 알려져 있다. 이러한 주철의 난용접성을 해결하는 방법으로는 고탄소 모재 용접시 발생하는 탄소의 확산을 억제하거나 예열이나 후열 처리를 통한 냉각 속도의 제어하는 방법과 오스테나이트 안정화 원소를 첨가한 필러와이어를 사용하여 용접시 마르텐사이트와 시멘타이트의 성장을 방해하는 방법 등이 이용되고 있다. 본 연구에서는 예열처리나 후열처리를 통한 주철의 용접법은 대량 생산을 통한 원가절감을 노리는 자동차 업계의 특성에 비추어 볼 때 비용이나 프로세스 구성 면에서 적용하는 것이 어려울 것이라 판단하여 Ni-base filler metal을 통한 주철의 용접법을 선택하였고 그 결과 실차에 적용하기 위한 비틀림 강성 테스트나 내구 테스트는 통과하였으나 NVH 테스트 결과 볼팅 체결 방식에 비하여 소음이 커지는 문제가 발생하고 링기어의 HAZ부가 고경화 되는 문제가 발생하였다. 때문에 용입깊이를 초기 시제품인 5mm에서 4mm로 변경시켜 입열량 감소 및 용접변형을 줄여 소음 문제를 해결하고자 하였으며 링기어의 침탄층을 1mm 절삭하여 링기어 HAZ부의 고경화 문제를 해결하고자 하였다. 이러한 용접 구조 변경이 용접변형 및 강성과 피로에 미치는 영향력을 알아보고자 용접 및 열처리 상용 소프트웨어인 SYSWELD, 구조해석 상용소프트웨어인 NX_NASTRAN, 피로 해석 상용 소프트웨어인 FEMFAT을 이용하여 시뮬레이션 하였고 실제 구조 변경한 용접 시제품과 비교, 분석하였다.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.22 no.3
• /
• pp.88-103
• /
• 2023

With the recent advancement of 4th Industrial Revolution technology, transportation systems are generating large amounts of mobility data related to the individual movement trajectories of vehicles and people. There are many constraints on utilizing mobility data containing personal information. Thus, in South Korea, the processing and generation of pseudonymized information and the analysis and utilization of this information have been managed in a dual manner by applying separate agencies and technologies through the revision of the Data 3 Act and the enactment of the Data Basic Act. However, this dual approach fails to securely support the entire data lifecycle and suffers from inefficiencies in terms of processing time and cost. Therefore, to compensate for the problems of the existing Expert Data Combination System and Data Safety Zone, this study proposes an Integrated Data Safety Zone Framework that integrates and unifies the process of generating, processing, analyzing, and utilizing mobility data. The integrated process for data processing was redesigned, and common requirements and core technologies were derived. The result is an architecture for a next-generation Integrated Data Safety Zone system that can manage and utilize the entire life cycle of mobility data at one stop.

• Journal of Korean Society of Environmental Engineers
• /
• v.32 no.2
• /
• pp.165-174
• /
• 2010

The numerical modeling of a coal gasification reaction occurring in an entrained flow coal gasifier is presented in this study. The purposes of this study are to develop a reliable evaluation method of coal gasifier not only for the basic design but also further system operation optimization using a CFD(Computational Fluid Dynamics) method. The coal gasification reaction consists of a series of reaction processes such as water evaporation, coal devolatilization, heterogeneous char reactions, and coal-off gaseous reaction in two-phase, turbulent and radiation participating media. Both numerical and experimental studies are made for the 1.0 ton/day entrained flow coal gasifier installed in the Korea Institute of Energy Research (KIER). The comprehensive computer program in this study is made basically using commercial CFD program by implementing several subroutines necessary for gasification process, which include Eddy-Breakup model together with the harmonic mean approach for turbulent reaction. Further Lagrangian approach in particle trajectory is adopted with the consideration of turbulent effect caused by the non-linearity of drag force, etc. The program developed is successfully evaluated against experimental data such as profiles of temperature and gaseous species concentration together with the cold gas efficiency. Further intensive investigation has been made in terms of the size distribution of pulverized coal particle, the slurry concentration, and the design parameters of gasifier. These parameters considered in this study are compared and evaluated each other through the calculated syngas production rate and cold gas efficiency, appearing to directly affect gasification performance. Considering the complexity of entrained coal gasification, even if the results of this study looks physically reasonable and consistent in parametric study, more efforts of elaborating modeling together with the systematic evaluation against experimental data are necessary for the development of an reliable design tool using CFD method.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.38 no.11
• /
• pp.771-780
• /
• 2001

It is indispensable to use the process and device simulation tool in order to analyze accurately the electrical characteristics of ULSI CMOS devices, in addition to developing and manufacturing those devices. The 3D Monte Carlo (MC) simulation result is not efficient for large-area application because of the lack of simulation particles. In this paper is reported a new efficient simulation strategy for 3D MC ion implantation into large-area application using the 3D MC code of TRICSI(TRansport Ions into Crystal Silicon). The strategy is related to our newly proposed split-trajectory method and ion-splitting method(ion-shadowing approach) for 3D large-area application in order to increase the simulation ions, not to sacrifice the simulation accuracy for defects and implanted ions. In addition to our proposed methods, we have developed the cell based 3D interpolation algorithm to feed the 3D MC simulation result into the device simulator and not to diverge the solution of continuous diffusion equations for diffusion and RTA(rapid thermal annealing) after ion implantation. We found that our proposed simulation strategy is very computationally efficient. The increased number of simulation ions is about more than 10 times and the increase of simulation time is not twice compared to the split-trajectory method only.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.32 no.1
• /
• pp.63-73
• /
• 2014

Recently, researches on DBRN(DataBase Referenced Navigation) system are being carried out to replace GNSS(Global Navigation Satellite System), as weaknesses of GNSS were found that are caused by the intentional interference and the jamming of the satellite signal. This paper describes the gravity gradient modeling and the construction of EKF(Extended Kalman Filter) based GGRN(Gravity Gradient Referenced Navigation). To analyze the performance of GGRN, fourteen flight trajectories were made for simulations over whole South Korea. During the simulations, we considered the errors in both DB(DataBase) and sensor as well as the flight altitudes. Accurate performances were found, when errors in the DB and the sensor are small and they located at lower altitude. For comparative evaluation, the traditional TRN(Terrain Referenced Navigation) was also developed and performances were analyzed relative to those from the GGRN. In fact, most of GGRN performed better in low altitude, but both of precise gravity gradient DB and gradiometer were required to obtain similar level of precisions at the high altitude. In the future, additional tests and evaluations on the GGRN need to be performed to investigate on more factors such as DB resolution, flight speed, and the update rate.

• Radiation Oncology Journal
• /
• v.15 no.4
• /
• pp.387-392
• /
• 1997

Purpose : To quantify the movement of lung Parenchyma for ICRU 50 Planning Target Volume (PTV) delineation of the lung region. Materials and Method : Fluoroscopic observations and measurements are Performed on 10 patients with chest region cancer who have normal putmonary functions We have divided the lung region into 12 parts for the right lung, 10 parts for the left lung and four to five Points of lung parenchyma were selected for anatomical analysis Points, Fluoroscopic images are sent to a computer and then movements are measured. Results : Both lowe lobes showed the longest longitudinal movements because of breathing (average 14.1mm, maximum 22.1mm), while anteroposterior displacement showed the smallest value. Lateral movements of the lung parenchyma averaged 6.6mm, and the maximum value was 9.1mm, (both hilar regions showed maximum values because of cardiac motion) Conclusion : We could quantify the lung movements by measuring parenchyma displacements. The movements of both upper lobes were less than those of the middle and upper lobes in longitudinal and transverse movements. Optimal margins can be selected for PTV delineation using these results.

• Spatial Information Research
• /
• v.23 no.2
• /
• pp.69-81
• /
• 2015

If one can infer the residential area of SNS users by analyzing the SNS big data, it can be an alternative by replacing the spatial big data researches which result from the location sparsity and ecological error. In this study, we developed the way of utilizing the daily life activity pattern, which can be found from timeline data of tweet users, to infer the residential areas of tweet users. We recognized the daily life activity pattern of tweet users from user's movement pattern and the regional cognition words that users text in tweet. The models based on user's movement and text are named as the daily movement pattern model and the daily activity field model, respectively. And then we selected the variables which are going to be utilized in each model. We defined the dependent variables as 0, if the residential areas that users tweet mainly are their home location(HL) and as 1, vice versa. According to our results, performed by the discriminant analysis, the hit ratio of the two models was 67.5%, 57.5% respectively. We tested both models by using the timeline data of the stress-related tweets. As a result, we inferred the residential areas of 5,301 users out of 48,235 users and could obtain 9,606 stress-related tweets with residential area. The results shows about 44 times increase by comparing to the geo-tagged tweets counts. We think that the methodology we have used in this study can be used not only to secure more location data in the study of SNS big data, but also to link the SNS big data with regional statistics in order to analyze the regional phenomenon.

• The KIPS Transactions:PartA
• /
• v.18A no.5
• /
• pp.215-224
• /
• 2011

In this paper, a mechanism connecting all weighted migration routes with minimum cost with EGOSST is proposed. Weighted migration routes may be converted to weighted input edges considered as not only traces but also traffics or trip frequencies of moving object on communication lines, roads or railroads. Proposed mechanism can be used in more wide and practical area than mechanisms considering only moving object traces. In our experiments, edge number, maximum weight for input edges, and detail level for grid are used as input parameters. The mechanism made connection cost decrease average 1.07% and 0.43% comparing with the method using weight minimum spanning tree and weight steiner minimum tree respectively. When grid detail level is 0.1 and 0.001, while each execution time for a connecting solution increases average 97.02% and 2843.87% comparing with the method using weight minimum spanning tree, connecting cost decreases 0.86% and 1.13% respectively. This shows that by adjusting grid detail level, proposed mechanism might be well applied to the applications where designer must grant priority to reducing connecting cost or shortening execution time as well as that it can provide good solutions of connecting migration routes with weights.

• Journal of the Korean association of regional geographers
• /
• v.22 no.4
• /
• pp.887-911
• /
• 2016

The empirical law that transverse dunes migrate inversely with their heights leads logically to the prediction that multiple dune ridges will converse to a single huge dune by merging. This contradicts the existence of the steady state dune fields on the Earth. The recent studies have emphasized dune collisions as a key mechanism to the stability of dunefield. The roles of wind shadow aspect ratio, however, have yet to be fully explored. This research aims to investigate the potential roles of wind shadow aspect ratio in the dynamical behaviors of transverse dune field. The simplified model is established for this, based upon allometric properties of transverse dunes, wind speedup on the stoss slope and sand trapping efficiency. The derived governing equations can be transformed to the zoning criteria and vector field for dune evolution. The dynamics analysis indicates that wind shadow aspect ratios do not produce convergent areas on the behavior space; rather, they just act as one of the factors that affect the trajectories of dune evolution. Though the model cannot represent the stability of dune field, but seem to produce a reasonable exponent for dune spacing-height relations.