• Journal of the Korean Wood Science and Technology
• /
• v.28 no.3
• /
• pp.14-24
• /
• 2000

In present research, the plywoods made of radiata pine or Japanese larch, the potential softwood species in mass supply, were discussed to examine their feasibility as the structural and concrete form panels through the basic properties test. First, plywood qualities and its nail performance were tested. The performance test for concrete form or structural panel by concentrated and uniformly distributed load were conducted to investigate the possibility as structural material for light frame and concrete constructions. Test results of basic quality such as specific gravity, cupping, bowing, and twisting appeared to satisfy the criteria for structural use. Also, nail performance test results, for roof and wall sheathing panels, nail lateral resistance, nail withdrawal resistance, and nail push head resistance proved to meet the required standard for structural use. The test results on performance as structural panel by concentrated and uniformly distributed load and as concrete form panel showed that these two species could be used for structural sheathing, subfloor, and concrete form panels.

• Journal of Korean Association for Spatial Structures
• /
• v.8 no.5
• /
• pp.67-74
• /
• 2008

Multi-layered stone masonry monuments, such as stone pagoda can be modeled as a multi-degrees of freedom system. The dynamic behavior of these structures are mainly influenced by contour condition of contacting surface of stones. In this case the mass of the system can be easily estimated, mean while the estimation of stiffness at junction is not simple. In this paper a method for estimating the spring constant at the contacting surface of stone in proposed. This paper describes a method of computational modelling technique for structural analysis of stone pagodas using measurement of natural frequency and eigenvalue analysis. For this purpose Five story stone pagoda in Cchongnimsa site was selected as a model.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.18 no.4
• /
• pp.92-98
• /
• 2014

Spacer is a construction material for maintaining cover depth and steel installation, however several problems like staining, leakage, and cracking are currently issued due to performance degradation and unsatisfactory dimensional stability of spacer. Plastic composite is widely used for prevention of brittle failure in cement based material, which yields improvement of crack resistance and ductile failure. This study is for development and applicability evaluation of high strength spacer with slag cement for environmental load reduction and plastic composite like polypropylene fiber, nylon fiber, and glass fiber. For this work, unit weight of 4 different plastic fibers are evaluated through preliminary tests. Physical tests including compressive, flexural, and tensile strength and durability tests including absorption, permeability, length change, crack resistance, carbonation, and freezing and thawing are performed. Through various tests, optimum plastic fiber is selected and manufacturing system for high strength spacer with the selected fiber is developed. Dimensional stability of the developed spacer is evaluated through field applicability evaluation.

• Journal of Conservation Science
• /
• v.36 no.6
• /
• pp.483-493
• /
• 2020

In this paper, we present a nondestructive analysis using X-ray and microscopic investigation to detect the structure, manufacturing technique and preservation status of the Goryeo lacquered box Inlaid with Mother-of-pearl Chrysanthemum and Scroll Design (Goryeo Lacquered Box). We confirm that the Goryeo Lacquered Box consists of the soft wood as the basic material. The soft wood was coated with textile and then lacquered. The box structure of the Goryeo Lacquered Box was formed of wooden boards with wood plants added to the side, after processing into a trefoil-shaped. The wooden sides of the Goryeo Lacquered Box were cut at regular intervals for easier processing into a curved shape. Moter-of-pearl, tortoiseshell, and metal wire were used to decorate the surface. mother-of pearl was the cutting processing, and tortoiseshell was used for back coloring. The metal line was constructed using one line and twist line.

• Journal of the Korean GEO-environmental Society
• /
• v.15 no.9
• /
• pp.59-67
• /
• 2014

With increasing underwater structure construction, there is high interest in offshore foundation and underwater grout and various study has been done in this area. For grout materials constructed underwater, it may be washed away by water or easily disturbed and material separation phenomenon during curing period always happens. As a result, it is difficult to ensure construction quality and this has a significant influence on the design strength of structure. In this study, to understand application effects of anti-washout admixture for the preplaced construction method, where grout is injected in monopile after filled with aggregates, laboratory tests on bleeding and compressive strength of anti-washout admixture were performed under various test conditions varying size of aggregate, water and cement ratio and admixture, and test results were compared and evaluated.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.14 no.6
• /
• pp.85-92
• /
• 2010

Recently the earthquake occurrences in Korea are likely to increase. Therefore, the facilities such as bridges and tunnels under the unexpected earthquakes need to be enhanced. Especially most of the subways previously built before 1988 have not been seismically designed, so their seismic safety requirements are required to be inspected and/or reinforced. In this study, the seismic reinforcement using FRP-ductile material layered composites was proposed to reinforce for the subway columns. Material properties of FRP-ductile material layered composites were calculated by laboratory tests considering the laminated conditions of the composites. Numerical simulations were performed using the experimental results of the specimens and the calculated properties of the composites. Seismic performance varied according to the types of composites: ductile material, number of layers, fiber orientations.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.20 no.4
• /
• pp.59-67
• /
• 2016

Concrete is a very useful construction material for the sealing disposal of hazardous substances. In general, mass concrete is applied to these structures. And, the mineral admixtures are recommended for the long term performance. Calcium leaching could be happened due to the contact with pure water in underground structures. Thus, it is needed to evaluate the resistance of calcium leaching for concrete mixed with mineral admixtures. From the test results, the mineral admixtures are effective to the improvement of long term compressive strength and chloride diffusion coefficient in concrete members. When calcium leaching is happened, however, the reduction of compressive strength and chloride penetration resistance is severe than OPC case, the micro pore distribution is adversely affected. Consequently, when the mineral admixtures are applied to underground structures which is exposed to calcium leaching environment, it is desirable to reduce water-to-binder ratio, to expose after the sufficient pozolanic reaction, and to use BFS than FA.

• Journal of the Society of Disaster Information
• /
• v.17 no.4
• /
• pp.839-847
• /
• 2021

Purpose: This study investigates mechanical behavior of functionally graded (FG) carbon nanotube-reinforced composite (CNTRC) plate in flexure. Isogeometric analysis (IGA) method coupled with shear deformable theory of higher-order (HSDT) to analyze the nonlinear bending response is presented. Method: Shear deformable plate theory into which a polynomial shear shape function and the von Karman type geometric nonlinearity are incorporated is used to derive the nonlinear equations of equilibrium for FG-CNTRC plate in bending. The modified Newton-Raphson iteration is adopted to solve the system equations. Result: The dispersion pattern of carbon nanotubes, plate geometric parameter and boundary condition have significant effects on the nonlinear flexural behavior of FG-CNTRC plate. Conclusion: The proposed IGA method coupled with the HSDT can successfully predict the flexural behavior of FG-CNTRC plate.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2005.05b
• /
• pp.1388-1392
• /
• 2005

호안 Mattress/Filter는 철망구조 내에 채움재를 채운 다공성 구조로서 다양한 크기의 채움재를 사용할 수 있고 이로 인하여 다양한 공극을 형성할 수 있다. 이러한 Mattress/Filter의 다공성 구조는 통수성을 증가시키기 때문에 호안부에서 흐름의 에너지 및 유속을 감소시키며, 이로 인해서 소류력이 감소되어 호안의 침식을 완화시킨다. 또한 Mattress/filter에 사용되는 채움재는 자갈, 폐콘크리트 및 슬래그를 사용하기 때문에 표면이 거칠고 조도계수가 증가하게 되며, 호안에서의 조도계수의 증가는 유속의 감소와 소류력 감소를 가져온다. 한편 Mattress/Filter가 시공되고 수개월이 경과되어 식생발달 및 안정화가 이루어진 후에는 식생과 Mattress/Filter가 일체화되며, Mattress/Filter와 식생에 의해 조도계수의 증가 및 유속감소의 효과가 더욱 커지면서 결과적으로 소류력 감소효과는 증가하게 된다. Mattress/Filter의 다공성 구조는 호안의 통수성 및 조도계수를 증가시켜 호안부의 유속 및 소류력을 감소시키기 때문에 침식 및 식생유실을 완화시키게 된다. 시공 초기 식생이 발달하기 전에 복토된 토양의 유실 우려가 있을 경우 Mattress/Filter의 표면에 토양유실방지매트를 설치하여 복토된 토양이 유수에 의해 침식되는 현상을 방지할 수 있다. Mattress/Filter 시공후 수개월이 경과한 뒤에는 식생이 발달하여 유속 및 소류력 저감효과가 더욱 증가하며, 이로 인해서 더욱 안정된 식생군락을 형성시킬 수 있었다.

• Journal of the Korea Computer Industry Society
• /
• v.3 no.3
• /
• pp.341-350
• /
• 2002

Software architectures can be restructured by modification and update during design processes, and appropriate software architectures for developments can be designed more than one. Therefore, it is required to specify efficiently the modification elements of architectures and restructuring method of designed architecture through various aspects. In this paper, we proposed software architecture restructuring mechanism that can restructure legacy architecture and a new software architecture designed with reuse of it in integrated form. And, we define specification elements and structure of the proposed restructured architecture specification. It provides the method that can reference and reuse architectures designed with various aspects of developers in architecture design processes. In addition, it supports flexible specification method for specification of modification elements such as revision, substitution, update of legacy software architecture.