• Journal of the Korea institute for structural maintenance and inspection
• /
• v.18 no.6
• /
• pp.139-146
• /
• 2014

Recently, in field of bridge construction, modular technology has been studied to reduce construction period, traffic impact and environmental impact. This study is a part of research related to the modular bridges. The aim of the study is to analyze the structural behavior and evaluate a serviceability for transverse connection of modular slab bridge. A total of four specimens were fabricated. including a control beam for finding the maximum load by static test. And one control beam and two segmental beams were fabricated for cyclic loading test. As the test result, the beams that were introduced 100% of the design prestressing force showed a smaller maximum deflection, residual deflection and crack width than the control beam. The beam for serviceability evaluation was satisfied with structural serviceability limits of the deflection and crack.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.26 no.3D
• /
• pp.435-444
• /
• 2006

This paper investigates the effect of 3-dimensional FE models to evaluation results of jointed concrete pavements which is back-calculated by AREA method. Sensitivity of 3-dimensional FE models developed to simulate the behavior of real jointed concrete pavement are analyzed after compared with 2-dimensional FE models using ILLISLAB. In comparison with 2-dimensional models, influence of concrete contraction under loading plate and base layer on surface deflections is more than that of loading configuration. Deflections at 3-dimensional model between linear and nonlinear temperature distribution under same temperature difference are similar, but noticeable differences are investigated in low elastic modulus of foundations. Dynamic deflections under loading plate are larger than static deflections in high elastic modulus of foundation, but smaller in low elastic modulus. Lower dynamic modulus of subgrade reactions are backcalculated by dynamic deflections than by static deflections. But reverse trend is investigated in the backcalculated elastic modulus of concrete which describes trends of the field backcalculation values calculated from AREA method.

• Journal of the Korean Geotechnical Society
• /
• v.39 no.12
• /
• pp.103-114
• /
• 2023

Monitoring the site of an underground construction wall is crucial to confirm the stability of the supports and ground due to excavation. In particular, it is essential to maintain the accuracy of a load cell gauge, which identifies the load of the support transmitted from the excavated ground. However, research on verification methods and regulations that can identify the accuracy of load cell gauges at construction sites is inadequate, which is a problem as load cell gauges are installed without proper performance inspections. In this study, performance tests were conducted by a complete investigation of load cell gauges sold in Korea and comparing them with foreign products to determine defect causes. In addition, the criteria for selecting a load cell gauge were presented, and the results of this study were considered to help select a highly reliable load cell gauge.

• Journal of the Korean Geotechnical Society
• /
• v.20 no.2
• /
• pp.5-13
• /
• 2004

Conventional railroad roadbeds constructed with soils can easily deteriorate with time due to the increase of repeated traffic loading, increase of train speed, built-up of ground water on the roadbed and decrease of permeability in the roadbed layer, etc. In this study, performance of reinforced railroad roadbeds with the crushed stones was investigated through the real scale roadbed tests and numerical analysis. It was found that the reinforced roadbed with crushed stone had less elastic and plastic vertical displacement(settlement) than general soil roadbed regardless of the number of loading cycles. It was also found through the actual testing that for the roadbed with the same thickness, the displacement of reinforced roadbed decreases with the increase of subgrade reaction modulus. The settlement of reinforced roadbed with the same subgrade reaction modulus also decreases with the increase of thickness of the reinforced roadbed. However, the subgrade reaction modulus is a more important factor to the total plastic displacement of the track than the thickness of the crushed stone roadbed.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.28 no.1D
• /
• pp.45-55
• /
• 2008

The objective of this research was to develop a VEPCD (ViscoElastoPlastic Continuum Damage) Model which is used to predict the behavior of asphalt concrete under various loading and temperature conditions. This paper presents the VEPCD model formulated in a tension mode and its validation using four hot mix asphalt (HMA) mixtures: dense-graded HMA, SBS, CR-TB, and Terpolymer. Modelling approaches consist of two components: the ViscoElastic Continuum Damage (VECD) mechanics and the ViscoPlastic (VP) theory. The VECD model was to describe the time-dependent behavior of HMA with growing damage. The irrecoverable (whether time-dependent or independent) strain has been described by the VP model. Based on the strain decomposition principle, these two models are integrated to form the VEPCD model. For validating the VEPCD model, two types of laboratory tests were performed: 1) a constant crosshead strain rate tension test, 2) a fatigue test with randomly selected load levels and frequencies.

• 한국도로학회지:도로
• /
• v.5 no.4 s.18
• /
• pp.36-46
• /
• 2003

포장구조체에서 요구되는 강도를 갖게 하는 구조 설계의 방법은 경험적 절차부터 반역학적 절차까지 발전되어 왔다. 재생 가열아스팔트혼합물이 기존의 가열아스팔트혼합물(HMA)과 비교하여 비슷하거나 때에 따라 더 좋은 성능을 가져오므로, AASHTO설계지침서에서는 본질적으로 재생(recycled) HMA 재료와 신생(virgin) HMA 재료간의 차이가 없다고 기술하고 있으며, 기존 HMA 재료에 사용되는 덧씌우기설계법의 구조회복 분석방법(structural rehabilitation analysis method)을 재생포장설계에도 권장하고 있다. 재생 가열아스팔트의 설계를 위한 AASHTO 방법은 설계교통량, 교통량 및 수행능력예측의 신뢰수준, 공용기간, 그리고 포장상태 평가지수에 의하여 결정된 포장구조체에서 요구되는 포장두께지수(SN)에 기초한다. 포장두께지수(SN)는 포장층 두께, 상대강도계수, 각 층의 배수조건들의 곱의 조합으로서 나타내어질 수 있다. 덧씌우기로 간주될 수 있는 재생된 층의 포장두께지수(SN)는 기존 포장에서의 포장두께지수와 보강된 포장에서 요구되는 포장두께지수의 차이에 의하여 계산되어질 수 있다. 상대강도계수의 값은 AASHTO 설계지침에 명시되어 있다. AI 방법은 교통량, 노상의 회복탄성계수, 그리고 설계두께를 계산하기 위한 표층과 기층의 종류를 사용한다. 이 방법은 재생된 가열혼합물질과 기존의 가열혼합물질과는 거의 비슷한 성능을 나타낸다고 본다. 또다른 AI 방법에 의하면 재생된 층은 덧씌우기층이라고 간주하고, 현재의 포장두께와 요구되어지는 포장두께 사이의 차를 이용하여 재생될 층의 두께를 산정한다. 소요되는 덧씌우기 두께는 포장의 현장 상태지수(condition rating)와 각 종류에 따른 포장체와 포장재료가 아스팔트 콘크리트층의 등가두께로 전환되어 나타나는 방법에 근거하여 결정될 수 있다. 또 다른 방법은 포장체 각 층의 물성과 하중을 이용한 컴퓨터 프로그램에 의하여 산정된 하중-변형 응답에 의한 설계 방법을 포함한다. 이런 방법들에서는 포장체는 탄성이나 점탄성층 위에서 탄성이나 점탄성 거동을 보인다고 가정한다. 재생 상온혼합물에서의 AASHTO 설계 방법은 가열혼합물의 설계방법과 유사하다. 그러나, 재생 상온혼합물에서의 상대강도계수는 시공방법에 좌우되므로, 기술자의 판단을 근거로 하여 결정되어져야 한다. AI방법에서는 포장구조체를 다층탄성구조라고 보고, 노상의 강도와 설계 교통량을 근거로 요구되는 포장두께를 결정한다. 재생 상온혼합물 기층의 두께는 재생 상온혼합물 기충 위에서 가열아스팔혼합물에 대하여 산정된 덧씌우기 두께를 이용하여 결정할 수 있다. 아스팔트 표면의 재생은 기존 포장의 구조적 능력을 정상적으로 개선할 수 없으므로, 표면 재생의 두께를 설계하는 방법은 없다. 그러나, 임의의 덧씌우기 두께는 기존의 덧씌우기 설계법에 기초하여 산정 할 수 있다. 만약 덧씌우기가 승차감만을 개선시킨다고 여겨진다면, 혼합물에서 사용되어지는 최대 골재 크기에 기초한 최소 두께를 결정할 수 있다.

• Journal of Advanced Navigation Technology
• /
• v.23 no.1
• /
• pp.44-54
• /
• 2019

In many countries, there are needs of new transportations to replace ground congestions due to growing number of cars. In addition, the increase in the number of cars held by economic growth will further increase traffic congestion in the future. To overcome this problem, many researches have been performed for personal air vehicle (PAV). In this study, the wing loading and the power-to-weight ratio that are major design parameters for the sizing of roadable PAVs were calculated for different kinds of airfoil and engine types. I.e., in the sizing process, the study was conducted to determine the design point using the graphs of wing loading, power-to-weight ratio, brake horse power, and fuel efficiency for the given mission profiles considering domestic environments and the FAR PART 23 which is the GA class aircraft certification standard. As a result of sizing, using diesel engine require high maximum take-off weight, wing area, and power compared to gasoline engine due to more engine weight.

• Journal of Advanced Navigation Technology
• /
• v.22 no.2
• /
• pp.111-122
• /
• 2018

At present, the ground transportation system is saturated in many countries including Korea. To overcome this problem, many researches of developing a roadable personal air vehicle (PAV) are being carried out to alleviate traffic congestion and to accomplish door-to-door mobility through three-dimensional traffic system. In this study, the thrust-to-weight ratio, the wing loading, and the power-to-weight ratio that are major design parameters for the sizing of roadable PAVs were calculated under the constraints of ground roll, climb rate, maximum cruise speed, service ceiling, stall speed. Also, in the sizing process, the study was conducted to determine the design point using the graphs of thrust-to-weight ratio, wing loading, power-to-weight ratio, and brake horse power for the mission profiles considering domestic environments and the FAR PART 23 which is the GA class aircraft certification standard.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.23 no.4
• /
• pp.120-130
• /
• 2019

In this study, based on the correlation between traffic volume data and vertical displacement data developed in previous research using the bridge maintenance big data of 2006, the vertical displacement estimation model using the traffic volume data of Gwangan Bridge for 10 years A comparison of the performance of the developed model with the current applicability is presented. The present applicability of the developed model is analyzed that the estimated displacement is similar to the actual displacement and that the displacement estimation performance of the model based on the structured regression analysis and the principal component analysis is not significantly different from each other. In conclusion, the vertical displacement estimation model using the traffic volume data developed by this study can be effectively used for the analysis of the behavior according to the traffic load of Gwangan Bridge.

• International Journal of Highway Engineering
• /
• v.5 no.4 s.18
• /
• pp.13-22
• /
• 2003

Several design methods from overseas are employed without considering different conditions such as material properties, climate, and traffic condition in this country. Therefore, there are limitations in application. Therefore, new pavement analysis system which is able to design a pavement efficiently and economically should be set up. In this study, 243 probable sections are classified depending on values of layer thickness and elastic modulus, and the effect of load types for the probable sections are analyzed. The section showing larger load distribution is chosen for analysis. As a result of sensitivity, a layer thickness has more influence on pavement than an elastic modulus does. The stress distribution of FWD test load is larger than that of circular load. This study compares outputs between nonlinear elastic model and linear elastic model. Based on the result, this study finds nonlinear elastic model considering stress condition in the ground is recommended for subbase.