• Korean Journal of Optics and Photonics
• /
• v.11 no.4
• /
• pp.271-278
• /
• 2000

We have fabricated and analyzed the lasing characteristics of 1.3$\mu\textrm{m}$ Spot-Size-Converter (SSC) integrated Fabry-Perot (FP) laser diodes, which are very promising light sources for optical subscriber networks. SSC-LDs has been developed by BIB (buttjoint-built-in) coupling and selective MOVPE growth. High-performances were achieved such as the slope efficiency from the SSC facet of 0.23-0.32 mW/mA, the full-width at the half maximum of the far-field pattern (FFP) of 9.5$^{\circ}$~12.3$^{\circ}$, the alignment tolerances of $\pm$2.3$\mu\textrm{m}$ and $\pm$2.5$\mu\textrm{m}$ within the extra-coupling loss of 1 dB for the vertical and parallel directions, respectively. These experimental results were compared to theoretical ones in order to clarify the operational problems and give a good design direction of the fabricated SSC-LDs. It was revealed that an asymmetric output power from the facets, an irrelevancy of FFP and the waveguide structure around SSC facet region, and a poor temperature characteristics were originated from the scattering in the BIB and SSC sections and SHB effect in the active section for the first time.t time.

• Korean Chemical Engineering Research
• /
• v.49 no.3
• /
• pp.320-324
• /
• 2011

TOPO/TOP capped CdSe nanoparticles were synthesized via thermal-solvent method. The 540 nm green and 620 nm red emitting CdSe nanoparticles were obtained by controlling the reaction time and temperature. Phosphor conversion white LED was produced combining a 460 nm emitting InGaN LED chip as an excitation source with 540 and 620 nm CdSe nanoparticles as phosphors. The single or double phosphor layer was fabricated by mixing with epoxy, and investigated the effects on the luminous properties of the white LED. The single phosphor layer white LED showed 5.78 lm/W with CIE of (0.36, 0.45) in reddish white, and the double phosphor layer white LED showed 7.28 lm/W with that of (0.32, 0.34) in pure white at 20 mA. When the 400 nm near-UV LED was applied to optical pumping source, the luminous efficiency of white LED was enhanced to 8.76 lm/W.

• Journal of the Institute of Electronics Engineers of Korea SP
• /
• v.38 no.4
• /
• pp.362-370
• /
• 2001

In this paper, we proposed multispectral image compression method using CIP (classified inter-channel prediction) and SVQ (selective vector quantization) in wavelet domain. First, multispectral image is wavelet transformed and classified into one of three classes considering reflection characteristics of the subband with the lowest resolution. Then, for a reference channel which has the highest correlation and the same resolution with other channels, the variable VQ is performed in the classified intra-channel to remove spatial redundancy. For other channels, the CIP is performed to remove spectral redundancy. Finally, the prediction error is reduced by performing SVQ. Experiments are carried out on a multispectral image. The results show that the proposed method reduce the bit rate at higher reconstructed image quality and improve the compression efficiency compared to conventional methods. Index Terms-Multispectral image compression, wavelet transform, classfied inter-channel prediction, selective vetor quantization, subband with lowest resolution.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.08a
• /
• pp.305-305
• /
• 2013

태양전지는 무기태양전지와 유기태양전지 등이 연구 되고 있는데 [1] 그 중 유기물질의 장점(높은 수율, solution phase processing, 저비용으로 전력 생산)과 무기재료의 장점(높은 전자 이동도, 넓은 흡수 범위, 우수한 환경 및 열 안정성)을 융합함으로써 장기적 구조안정성의 확보와 광전변환의 고 효율화를 동시에 달성하기 위한 유기무기 하이브리드 태양전지가 최근 큰 관심을 끌고 있다[2]. 본 연구에서는 hybrid photovoltaics에 유기물 MDMO-PPV와 전도성 고분자 PEDOT:PSS를 무기물 GaN 위에 spin coating 하여 두께에 다른 효율을 측정하였다. 유기물 MDMO-PPV는 p-형으로 클로로벤젠, 톨루엔과 같은 유기 용매에 잘 녹으며 HOMO 5.33eV, LUMO 2.97eV, energy band gap 2.4eV이며 99.5%의 순도 물질을 사용하였다. 또한 정공 수송층(hole transport layer, HTL)으로 PEDOT:PSS를 사용하였으며, HOMO 5.0eV, LUMO 3.6eV, energy band gap 1.4eV를 가지며 증류수나 에탄올과 같은 수용성 용매에 잘 녹는 특성을 가지고 있다. 무기물은 III-V 족 물질 n-GaN(002)을 사용하였고 valence band energy 1.9eV, conduction band energy 6.3eV, energy band gap 3.4eV, 높은 전자 이동도와 높은 포화 속도, 광전자 소자에 유리한 광 전기적 특성을 가지고 있다. 기판으로는 GaN와 격자 부정합도와 열팽창계수 부정합도가 큰 Sapphire (Al2O3) 이종 기판을 사용하였다. 전극으로 Au를 사용하였으며 E-beam증착하였다. Reflector로서 Al를 thermal evaporator로 증착하였다 [3]. 실험 과정은 두께에 따른 효율을 알아보기 위해 MDMO-PPV를 900~1,500 rpm으로 spin coating 하였고, 열처리에 따른 효율을 알아보기 위해 열처리 온도 조건을 $110{\sim}170^{\circ}C$의 변화를 주었다. FE-SEM으로 표면과 단면을 관찰하였으며 J-V 특성을 알아보기 위해 각 샘플마다 solar simulator를 사용하여 측정하였고 그 결과를 논의하였다.

• Journal of the Microelectronics and Packaging Society
• /
• v.23 no.2
• /
• pp.65-71
• /
• 2016

In this study, Antimony Tin Oxide (ATO) ion storage layer and $TiO_2$ working electrode were fabricated using Nano Particle Deposition System. NPDS is the cutting-edge technology among the dry deposition methods. Accelerated particles are deposited on the substrate through the nozzle using NPDS. The thicknesses for coated layers were measured and layer's morphology was acquired using SEM. The fabricated electrochromic cell's transmittance was measured using UV-Visible spectrometer and power source at 630 nm. As a result, the integrated electrochromic/DSSC hybrid system was successfully fabricated as an energy harvesting system. The fabricated electrochromic cell was self-operated using DSSC as a power source. In conclusion, the electrochromic cell was operated for 500 cycles, with 49% of maximum transmittance change. Also the photovoltaic efficiency for DSSC was measured to be 2.55% while the electrochromic cell on the integrated system had resulted in 26% of maximum transmittance change.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.8 no.2
• /
• pp.83-90
• /
• 2009

White LEDs(Light Emitting Diode) offer advantageous properties such as high brightness, improved reliability, lower power consumption, and long lifetimes. An LED is an electronic device that converts an electrical signal into a tight signal and is used not only in Optical Communication Indoor wireless optical illuminating rooms, but also for wireless optical communication systems. Currently, studies about these white LEDs have been being progressed, and in this raper, we discuss the multiplex and the multiple access method of VLC(Visible Light Communication) systems using white LEDs. In proposed system, CDMA(Code Division Multiple Access) apples to VLC system to reduce interference of VLC system, and improve capacity. The superiority of OOK modulation is presented in analysis of results by comparing VLC-CDMA communication system using OOK(On-off keying) modulation and BPSK modulation in AWGN(Additive White Gaussian Noise) channel and Diffuse channel. And we investigate the significance of a solution of interference by multipath by comparing BER in multipath channel and AWGN channel. In the proposed system, we assume Directed LOS(Line Of Sight) and Diffuse Link, and suppose VLC-CDMA using OOC(Optical Orthogonal Code) as methods to increase efficiency of system by removing ISI(Inter Symbol Interference) caused by multiple access, optical spreading code, and also present an analysis of its performance.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.15 no.4
• /
• pp.665-670
• /
• 2020

Buffer layer in CIGS thin-film solar cells improves energy conversion efficiency through band alignment between the absorption layer and the window layer. ZnS is a non-toxic II-VI compound semiconductor with direct-transition band gaps and n-conductivity as well as with excellent lattice matching for CIGS absorbent layers. In this study, the structural and optical properties of ZnS thin films, deposited by RF magnetron sputtering method and subsequently performed by the rapid thermal annealing treatment, were investigated for the buffer layer. The zincblende cubic structures along (111), (220), and (311) were shown in all specimens. The rapid thermal annealed specimens at the relatively low temperatures were polycrystalline structure with the wurtzite hexagonal structures along (002). Rapid thermal annealing at high temperatures changed the polycrystalline structure to the single crystal of the zincblende cubic structures. Through the chemical analysis, the zincblende cubic structure was obtained in the specimen with the ratio of Zn/S near stoichiometry. ZnS thin film showed the shifted absorption edge towards the lower wavelength as annealing temperature increased, and the mean optical transmittance in the visible light range increased to 80.40% under 500℃ conditions.

• Korean Journal of Optics and Photonics
• /
• v.33 no.4
• /
• pp.137-145
• /
• 2022

A directional coupler device, one of the fundamental components of photonic integrated circuits, distributes optical power by evanescent field coupling between two adjacent optical waveguides. In this paper, the design process for manufacturing a directional coupler device is reviewed, and the accuracy of the design results, as seen from the characteristics of the actual fabricated device, is confirmed. When designing a directional coupler device through a two-dimensional (2D) beam-propagation-method (BPM) simulation, an optical structure is converted to a two-dimensional planar structure through the effective index method. After fabricating the directional coupler device array, the characteristics are measured. To supplement the 2D-BPM results that are different from the experimental results, a 3D-BPM simulation is performed. Although 3D-BPM simulation requires more computational resources, the simulation result is closer to the experimental results. Furthermore, the waveguide core refractive index used in 3D-BPM is adjusted to produce a simulation result consistent with the experimental results. The proposed design procedure enables accurate design of directional coupler devices, predicting the experimental results based on 3D-BPM.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.08a
• /
• pp.345-345
• /
• 2012

최근 의료산업에서는 고해상도 및 동영상 구현이 가능한 직접 방식의 X-선 검측센서에서 X-ray 흡수효율이 좋은 반도체 센서(CdTe, CdZnTe 등)와 성숙된 기술, 집적효율이 뛰어난 CMOS 공정을 이용한 제품을 출시하여 대면적화 및 고집적화가 가능하게 되어 응용분야가 점차 확대되고 있는 추세이다. 하지만 이 역시 고 성능의 X-선 동영상 구현을 위해서는 고 해상도 문제, 검출효율 문제, 대면적화의 어려움이 있다. 기존의 X-선 광 도전층의 증착은 증착 속도와 박막 품질에서 우수한 Evaporation 법이 사용되고 있다. 한편, 대면적에 균일한 박막형성이 가능하기 때문에 양산성에서 우월성을 가지는 sputtering법의 경우, 밀도가 높은 소결체 타겟의 제조가 힘들뿐만 아니라 증착 속도가 낮아 장시간 증착 시 낮은 소결밀도로 인한 타겟 Particle 영향으로 인해서 대 면적에 고품질의 박막을 형성하기가 어렵다. 하지만 최근 소결체 타겟 제조기술 발달과 함께, 대면적화와 장시간 증착에 대한 어려움이 해결되고 있어 sputtering 법을 이용한 고품질 박막 제조 기술의 연구가 시급한 실정이다. 본 연구에서는 $50{\times}50$ mm 크기의 non-alkali 유리기판(Corning E2000) 위에 Evaporation과 RF magnetron sputtering을 사용하여 다양한 기판온도 (RT, 100, 200, 300, $350^{\circ}C$)에서 $1{\mu}m$의 두께로 CdTe 박막을 증착하였다. RF magnetron sputtering의 경우 CdTe 단일 타겟(50：50 at%)을 사용하였으며 Base pressure는 약 $5{\times}10^{-6}$ Torr 이하까지 배기하였고, Working pressure는 약 $7.5{\times}10^{-3}$ Torr에서 증착하였다. 시편과 기판 사이의 거리는 70 mm이며 RF 파워는 150 W로 유지하였다. CdTe 박막의 미세구조는 X-ray diffraction (XRD, BRUKER GADDS) 및 Field Emission Scanning Electron Microscopy (FE-SEM, Hitachi)를 사용하여 측정하였다. 또한, 조건별 박막의 조성은 Energy Dispersive X-ray Spectroscopy (EDS, Horiba, 7395-H)을 사용하여 평가하였다. X-선 동영상 장치의 구현을 위해서는 CdTe 다결정 박막의 높은 흡수효율, 전하수집효율 및 SNR (Signal to Noise Ratio) 등의 물성이 요구된다. 이러한 물성을 나타내기 위해서는 CdTe 박막의 높은 결정성이 중요하다. Evaporation과 RF magnetron sputtering로 제작된 CdTe 박막은 공정 온도가 증가함에 따라 기판상에 도달하는 스퍼터 원자의 에너지 증가로 인해서 결정립이 성장한 것을 확인할 수 있었다. 따라서 CdTe 박막이 직접변환방식 고감도 X-ray 검출기 광도 전층 역할을 수행할 수 있을 것으로 기대된다.

• Applied Chemistry for Engineering
• /
• v.18 no.4
• /
• pp.356-360
• /
• 2007

Recently, dye sensitized solar cells (DSSCs) composed of nanoporous $TiO_2$, light-sensitive dyes, electrolytes, and counter electrode have been received much attention. Nanostructured particles with higher surface area for the higher adsorption of Ru (II) dye are required to increase the quantity of light absorption. Also, it has been reported that the key factor to achieve high energy conversion efficiency in the photoelectrode of DSSC is the heat treatment of $TiO_2$ paste with acid addition. In this work, we investigated the influence of acid treatment of $TiO_2$ solar cell on the photovoltaic performance of DSSC. The working electrodes fabricated in this work were characterized by X-ray photoelectron spectroscopy (XPS), extended X-ray absorption fine structure (EXAFS), field emission scanning electron microscope (FE-SEM), and atomic force microscope (AFM). In addition, the influence of nanostructured photoelectrode fabricated with the acid-treated paste on the energy conversion efficiency was investigated on the basis of photocurrent-potential curves. It was found that the influence of acid-treated paste on the photovoltaic efficiency was significant.