• Journal of Plant Biology
• /
• v.35 no.4
• /
• pp.365-370
• /
• 1992

다양한 배양조건을 이용하여 당근 모상근의 생장과 carotenoid 함량을 조사하였으며, 이러한 배양조건을 airlift형생물 반응기에 적용하여 모상근의 다량 배양을 시도하였다. 고형배지 배양에서의 carotenoid 함량은 광조건에서 배양된 모상근이 암조건에서 배양된 모상근보다 10배 정도 증가하였으며, 모상근의 생장은 광조건이 암조건보다 낮은 수준이었다. 공기 유출기 배양에서는 모상근이 광조건과 암조건 모두에서 매우 빠르게 생장하여 생줄량의 차이가 없었으며, 모상근의 생장과 carotenoid 함량에 있어서 빛의 조사는 모상근의 전체적인 생중량을 증가시키기 보다는 배양 후기 생장단계에서 carotenoid 함량을 증가시켜서 암조건에 비하여 10배 정도의 carotenoid(11 $\mu\textrm{g}$/g)를 생산하였다. 모상근을 생물 반응기에서 배양하였을 때, 모상근이 지수함수적으로 빠르게 생장하여 배양 25일 동안에 처음 무게의 11배를 나타내었다. 그리고 pH는 처음 5.5에서 5일후 4.9로 떨어지다가 그 이후에 일정한 수준(pH 4.8)을 보여주었으며, 광주기와 광도을 조절하지 않은 상태에서의 carotenoid 함량은 2$\mu\textrm{g}$/g으로 나타났다.

• Journal of Ginseng Research
• /
• v.12 no.1
• /
• pp.30-39
• /
• 1988

This study was conducted to investigate the effects of light intensity and temperature on the physiological characteristics and growth of ginseng leaves. The higher the transmittance of the shade, the greater the area was decreased. In contrast, however, the amount of transpiration was increased. There was no significant difference in the number of stomata, but the size of stomata was distinctively decreased. The higher the transmittance of the shade, the more the contents of total chlorophyll, chlorophyll a and b, and cartooned were decreased. In contrast, however, the aye ratio of chlorophyll was increased. Regardless of temperature, the contents of chlorophyll providing maximum photosynthesis at the end of June and August were 2.1mg and 1 8mg/g F.W. respectively.

• Journal of the Korean Society of Radiology
• /
• v.16 no.3
• /
• pp.257-263
• /
• 2022

In intracavitary radiotherapy, it is essential to verify the correct location of radiation source among quality control items because an incorrect location will irradiate an unnecessary dose to normal tissues. As a basic study of digital line dosimeters, this study fabricated a unit cell dosimeter based on polycrystalline mercury (II) iodide (HgI₂) and compared its performance with a diode. The study result showed that for reproducibility, the relative standard deviation (RSD) was 1.21%, satisfying the RSD evaluation criterion of within 1.5%. Considering linearity, the coefficient of determination R² showed an excellent result of 0.9997. Regarding the evaluation of distance dependence, it showed a similar trend in general with a difference of 0.035 cm for intensity 50% when compared with the inverse square value. This study suggests the applicability of a digital dosimeter for brachytherapy quality control by evaluating the performance of the HgI₂ dosimeter. This study on dosimeter for candidate photoconductor materials can be used as basic data in all areas using radiation.

• Korean Journal of Ecology and Environment
• /
• v.52 no.4
• /
• pp.293-305
• /
• 2019

In this study we investigated the effect of a floating photovoltaic (FPV) system in Cheongpung Lake on water quality. The FPV with a tilt angle of 33° covered ca. 0.04% of surface area (97 ㎢) of Chungju Lake. The water qualities of the whole lake before and after installation of FPV were first compared. DO, BOD, TOC, and Chl-a of the whole lake were increased, while conductivity decreased after installation period at the significance level of 0.05. This change was probably due to the increased influx of nutrients by 40% resulting from increased precipitation during the same period. We also measured water quality parameters on May and Nov. 2017 at the FPV center (FPVC) and nearby control sites, and compared water quality. The result showed that the FPVC and nearby sites were not significantly different (p>0.05), demonstrating that the FPV does not cause a decline of water quality. The water temperature, light intensity, and phytoplankton community were also measured. The water temperature was not different between the sites, while the light intensity decreased to 27~50%. Despite reduced light intensity at FPVC, the phytoplankton standing crops and the number of species were not significantly different (p>0.05). However, in the early November samples, standing crops was significantly higher in FPVC than control with periphytic diatoms belonging to Aulacoseira genus being dominant. This may be due to the temporal water body behavior or local retention of current by FPV system. This study may provide a measure of future installation of a FPV system.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.40 no.1
• /
• pp.110-117
• /
• 2012

This study was performed to determine light-adaptability under indoor lighting for Korean wild Daphniphyllum macropodum, and to provide an introduction plan for indoor spaces of landscape architecture. The experimental plants, Daphniphyllum macropodum were purchased from a farmhouse in Jejudo as anannualplant, and it was acclimatized in the glass-green house of the general farm of Gyeongnam National University of Science and Technology for40 days. The experiment was performed from February 15, 2010 to November 15, 2010. First, in the case of the fluorescent lamp, the growth and development condition was poor because the plants withered, or the leaves fell off under the 100lux to 500lux, but the condition under 1,000lux was good In the aspects of the number of leaves, form of the tree, photosynthesis rate in its body, and the value of sight, the best light intensity for the growth condition was under the 1,000lux. Second, in the case of the LED light, the growth and development condition was poor because the plants withered, or the leaves fell off under 100lux to 1,000lux, but the smooth growth and development was done under a more light intensity. The best intensity for the growth condition was under 2,000lux. Third, in the case of the three-wave light, the withering was serious by 1,000lux, and the growth and development was the worst amongst the four introduced lighting systems, therefore, growth under the three-wave light was incongruous. The best intensity for the growth condition was under 2,000lux. Fourth, in the case of the optical fiver, the withering did not existed under 100lux and growth was possible. The growth and development was the amongst in the four introduced lighting systems. Generally, in the more light intensity, more growth was observed, but the value of sight was higher under 1,000lux than under 2,000lux because the falling rate of leaves and the form of the tree was stable. The most effective light was under 1,000lux due to the high photosynthesis in its body. When Daphniphyllum macropodum is introduced into the indoor landscaping space considering the light, the optical fiber, fluorescent lamp, and LED light are suitable to introduce. The three-wave light is unfit. The most proper light intensity by the light source, in the case of the optical fiber, and fluorescent lamp, is 1,000lux, and, in the case of LED light, is 2,000lux. The wild Daphniphyllum macropodum is the species of tree to substitute the Schefflera actinophylla which is the introduced species, and it is expected to be use as the central tree in indoor spaces.

• Restorative Dentistry and Endodontics
• /
• v.27 no.2
• /
• pp.158-174
• /
• 2002

The aim of this study was to investigate the effect of light irradiation modes on polymerization shrinkage, degree of cure and microleakage of a composite resin. VIP$^{TM}$ (Bisco Dental Products, Schaumburg, IL, USA) and Optilux 501$^{TM}$ (Demetron/Kerr, Danbury, CT, USA) were used for curing Filtek$^{TM}$ Z-250 (3M Dental Products, St. Paul., MN, USA) composite resin using following irradiation modes: VIP$^{TM}$ (Bisco) 200mW/$\textrm{cm}^2$ (V2), 400mW/$\textrm{cm}^2$ (V4), 600mW/$\textrm{cm}^2$ (V6), Pulse-delay (200 mW/$\textrm{cm}^2$ 3 seconds, 5 minutes wait, 600mW/$\textrm{cm}^2$ 30seconds, VPD) and Optilux 501$^{TM}$ (Demetron/Kerr) C-mode (OC), R-mode (OR). Linear polymerization shrinkage of the composite specimens were measured using Linometer (R&B, Daejeon, Korea) for 90 seconds for V2, V4, V6, OC, OR groups and for up to 363 seconds for VPD group (n=10, each). Degree of conversion was measured using FTIR spectrometer (IFS 120 HR, Bruker Karlsruhe, Germany) at the bottom surface of 2 mm thick composite specimens V2, Y4, V6, OC groups were measured separately at five irradiation times (5, 10, 20, 40, 60 seconds) and OR, VPD groups were measured in the above mentioned irradiation modes (n=5 each). Microhardness was measured using Digital microhardness tester (FM7, Future-Tech Co., Tokyo, Japan) at the top and bottom surfaces of 2mm thick composite specimens after exposure to the same irradiation modes as the test of degree of conversion(n=3, each). For the microleakage test, class V cavities were prepared on the distal surface of the ninety extracted human third molars. The cavities were restored with one of the following irradiation modes : V2/60 seconds, V4/40 seconds, V6/30 seconds, VPD , OC and OR. Microleakage was assessed by dye penetration along enamel and dentin margins of cavities. Mean polymerization shrinkage, mean degree of conversion and mean microhardness values for all groups at each time were analyzed using one-way ANOVA and Duncan's multiple range test, and using chi-square test far microleakage values. The results were as follows : . Polymerization shrinkage was increased with higher light intensity in groups using VIP$^{TM}$ (Bisco) : the highest with 600mW/$\textrm{cm}^2$, followed by Pulse-delay, 400mW/$\textrm{cm}^2$ and 200mW/$\textrm{cm}^2$ groups, The degree of polymerization shrinkage was higher with Continuous mode than with Ramp mode in groups using Optilux 501$^{TM}$ (Demetron/Kerr). . Degree of conversion and microhardness values were higher with higher light intensity. The final degree of conversion was in the range of 44.7 to 54.98% and the final microhardness value in the range of 34.10 to 56.30. . Microleakage was greater in dentin margin than in enamel margin. Higher light intensity showed more microleakage in dentin margin in groups using VIP$^{TM}$ (Bisco). The microleakage was the lowest with Continuous mode in enamel margin and with Ramp mode in dentin margin when Optilux 501$^{TM}$ (Demetron/Kerr) was used.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.08a
• /
• pp.265-266
• /
• 2012

의료용 X-ray의 발전에 따라, 영상의 Digital화가 필요하게 되었다. Digital 영상 구현을 위해 다양한 형태의 영상 검출기가 개발되었다. 진단 영상의 조건으로는 구현 시간이 빠르고 해상도가 높아야 한다. 조건에 부합하는 Flat panel 형태의 직접방식과 간접방식 검출기의 개발이 주로 이루어졌으며, X-ray 검출 효율이 높고 공간 분해능이 높은 직접 방식의 검출기에 대한 연구가 활발히 진행되고 있다. 기존 직접방식의 X-ray 검출물질로는 A-Se이 이용되었다. 하지만 A-Se의 경우 낮은 원자번호로 인해 X-ray에 대한효율이 낮으며, 제조 공정과 수율의 문제로 인해 대체 물질의 개발과 공정의 개선이 필요하다. 선행 연구를 통해 X-ray 검출물질의 전기적 특성을 파악을 통해 대체 물질로서 가능성을 알아보았다. 본 연구에서는 기존에 제작된 X-ray 검출물질의 상부전극 증착 물질과 증착법 선정에 대한 연구이다. 선행 연구를 통해 선정된 X-ray 검출물질은 HgI2이다. 상, 하부 전극 선택에 있어 HgI2의 일함수 값(4.15eV)을 고려하여 그와 비슷한 일함수 값을 가진 물질로 전기적 장벽을 제거하여야 한다. 따라서, ITO (일함수 4.45eV)와 Au (일함수 5.1eV)을 선택하였다. ITO의 증착으로 이용된 방법으로는 on-axis 형태의 magnetron plasma sputtering을 이용하였으며, Au의 증착으로 이용된 방법은 Thermal evaporation deposition을 이용하였다. plasma sputtering에 이용된 타겟은 In2O3;SnO2 (조성비:90:10wt%)를 사용하였으며, Chamber의 크기는 넓이 456 ${\phi}cm^2$ 높이 25 cm이며, 로 target과 기판과의 거리는 15cm이다. plasma발생에 필요한 가스로는 Ar과 O2를 이용하였다. 고 진공 환경 조성에 이용된 장비로는 Rotary pump와 Turbo molecular pump이다. plasma 발생 전 진공도는 $3.2{\times}10^{-5}$ Torr, 발생 후 진공도는 $5.1{\times}10^{-5}$ Torr이다. plasma 환경이 조성된 후 증착 시간은 1분 30초이다. Au는 순도 99.999%를 이용하였으며, 이용된 금은 1회 증착에 0.3 g을 이용하였다. Chamber의 넓이 1,444 ${\phi}cm^2$이며, 높이 40 cm, boat와 기판과의 거리는 25 cm이다. 고 진공 환경 조성에 이용된 장비로는 Rotary pump와 diffusion pump를 이용하였다. Au의 승화 전 진공도는 $2.4{\times}10^{-5}$ Torr 증착 시 진공도는 $4.2{\times}10^{-5}$ Torr이며, Boat에 가해준 전압, 전류는 0.97 V, 47 A이며, 증착 시간은 1분 30초이다. 광도전체 층에 각각 증착된 전극의 저항을 통해 증착상태를 판단하였다. DMM (Digital Multimeter)로 1 cm 간격으로 측정된 표면의 저항은 ITO 약 $8{\Omega}$, Au 약 $3{\Omega}$으로 전극으로서 이용이 가능한 상태이다. Au와 ITO가 증착된 HgI2 시편의 전기적 특성은 기존에 이용된 X-ray 변환물질의 성능보다 우수하였다. 하지만 Au와 ITO가 각각 증착된 시편의 전기적 특성은 큰 차이를 보이지 않았다. ITO의 경우 진공 상태에서 이용되는 Gas가 이용되며, Plasma 환경 조성 유지가 어려운 점이 있다. Au전극은 증착 환경 조성이 쉽지만, 전극 물질 이용효율이 떨어지는 단점이 있다. 본 연구를 통해 X-ray 변환물질인 HgI2의 전극물질로 Au와 ITO의 이용가능성을 알아보았다. 두 전극으로 제작된 검출기의 성능은 큰 차이 없이 우수하였고, 전기적 장벽 상태가 낮아 높은 검출 효율을 보였다. 상대적으로 Au 전극의 공정이 간단하고 수율이 높다. 하지만 Au Source의 이용 효율이 떨어지는 단점이 있다. 본 연구의 결과를 통해 공정상의 유리함과 Source의 이용효율을 고려한 분석에 대한 연구가 필요할 것으로 사료된다.

• Journal of the Korean Society of Radiology
• /
• v.4 no.4
• /
• pp.37-40
• /
• 2010

In this paper, transport properties of charge carrier which is produced by x-ray exposure were investigated.. It is the research of charge transport and specific property of trap that is performed in direct digital x-ray image receptor. We measured transit time and drift mobility of charge carriers of a-Se photoconductor using time-of-flight method. We made a testing glass with a-Se of $100{\mu}m$ thickness on corning glass using thermal evaporation method. As a result of this experiment, electron and hole transit time was each $229.17{\mu}s$ and $8.73{\mu}s$ at $10V/{\mu}m$ electric field and drift mobility was each $0.00174cm^2/V{\cdot}s$, $0.04584cm^2/V{\cdot}s$. But the results shows us different measurement value of electron and charge drift mobility and it was investigated about charge transport properties and trap mechanism.

• Journal of the Korean Society of Radiology
• /
• v.3 no.4
• /
• pp.35-38
• /
• 2009

Flat-panel x-ray detectors using a phosphor and photoconductor material have been used for application in various medical modalities. In this study, the monte carlo simulation, optical and x-ray response characteristics were investigated in the conversion structure obtained by a columnar CsI:Na scintillation layer with a photosensitive amorphous selenium layer. Firstly, from the measurement of luminescent spectrum of CsI:Na and absorption spectrum of a-Se layer, the signal conversion characteristics are analysed. And also, the x-ray sensitivity is measured and compared with conventional a-Se($500{\mu}m$) as a function of electrical field. From the experimental result, the x-ray sensitivities of the CsI:Na($180{\mu}m$)/a-Se($30{\mu}m$) detector and the a-Se($500{\mu}m$) detector were $7.31nC/mR-cm^{2}$ and $3.95nC/mR-cm^{2}$at an electric field of $10V/{\mu}m$, respectively.

• Journal of Animal Science and Technology
• /
• v.49 no.1
• /
• pp.147-154
• /
• 2007

To characterize the colorization patterns of bovine hairs, the melanin contents were quantitatively assayed and compared among cattle breeds. The total melanin levels measured by spectrophotometric assay (A500) from Jeju Black cattle were significantly lower than those from Holstein or Angus with black coat color but significantly higher than those from Hanwoo with yellow coat color or Angus and Holstein with red coat color (P<0.001). The total melanin levels from Hanwoo were significantly lower than those from Red Angus and Red Holstein but significantly higher than those from Hanwoo×Charolais crossbred (P<0.001). The relative ratios of eumelanin to pheomelanin (A650/A500) were 0.382, 0.359, 0.112 and 0.124 in Angus, Jeju Balck cattle, Red Holstein and Hanwoo, respectively. These results show that the spectrophotometric method provides a convenient way to qualitatively characterize hair melanin and may be useful for studying expression of major coat color genes in Hanwoo and Jeju Black cattle.