• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.43 no.12 s.354
• /
• pp.47-54
• /
• 2006

This work proposes a dual-channel 6b 1GS/s ADC for ultra wide-band communication system applications. The proposed ADC based on a 6b interpolated flash architecture employs wide-band open-loop track-and-hold amplifiers, comparators with a wide-range differential difference pre-amplifier, latches with reduced kickback noise, on-chip CMOS references, and digital bubble-code correction circuits to optimize power, chip area, and accuracy at 1GS/s. The ADC implemented in a 0.18um 1P6M CMOS technology shows a signal-to-noise-and-distortion ratio of 30dB and a spurious-free dynamic range of 39dB at 1GS/s. The measured differential and integral non-linearities of the prototype ADC are within 1.0LSB and 1.3LSB, respectively. The dual-channel ADC has an active area of $4.0mm^2$ and consumes 594mW at 1GS/s and 1.8V.

• Journal of Satellite, Information and Communications
• /
• v.6 no.1
• /
• pp.86-96
• /
• 2011

In this paper we propose a Pre-rake system applied with a frequency domain equalizer in TDD/CDMA multi-code transmission. The Pre-rake system has been well known technique in TDD/CDMA to make a receiver simple. However, it still has residual losses of path diversity and signal to noise ratio (SNR). However, gathering all the residual paths demands an additional hardware such as a rake combiner at the receiver. For the reason Pre/Post-rake system has already been proposed at up/downlink correlated channel conditionunder the assumption of noisier channel. There is a trade-off between the first purpose of Pre-rake that makes hardware simple at the receiver and the performance improvement. From the point the frequency domain equalizer (FDE) can be considered in Pre/Post-rake to supply the receiver with the flexible equalizing methods with rather reduced complexity compared with time domain rake combiner or equalizers. Pre-rake itself increases the number of multipath, which results from the convolution of Pre-rake filter and wireless channel, and FDE must be well matched to Pre/Post-rake, while it considers the relationship of hardware complexity and the performance. In this paper, the Pre-rake/Post-FDE system is introduced at TDD/CDMA multi-code transmission. In addition, the cyclic prefix reduction method in the proposed system is introduced, and the theoretical analysis to the proposed system is given by assuming Gaussian approximation, and finally the numerical simulation results are provided.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.31 no.4B
• /
• pp.323-332
• /
• 2006

In this paper, we consider a WDM based metro ring connecting broadband access networks by using FT-TR (Fixed Transmitter-Tunable Receiver) type access nodes and a new MAC protocol for fair transmission is proposed. The basic channel access scheme is CSMA/CA(Carrier Sense Multiple Access with Collision Avoidance) and the transferred optical slot is changed to be empty slot by SS(Source-Stripping) which drops a packet from ring-rotated slot. This empty slot can be either used to send head-of-line packet in buffer or transmitted to next access node. In former cases, there is the improvement of network throughput, but latter case leads unfairness problem of transmission. Thus the proposed MAC protocol exploits the advantages form tow cases. It gives downstream access nodes chance to use empty slots and limits the unconditional usage of empty slots at upstream access nodes with probability as called p-Persistent MAC protocol. We use a numerical analysis to evaluate bandwidth efficiency and maximum node throughput and compares simulation results in terms of node throughput, fairness factor, transfer delay depending on probability. Under two different FT-TR type architectures for metro ring network the proposed MAC protocol is evaluated and compared.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.33 no.9B
• /
• pp.751-759
• /
• 2008

Carrier Ethernet backbone network integrates distributed layer-2 based metro networks. In this networks, Multiple Spanning Tree Protocol (MSTP) has been uscd as a main routing protocol that allows multiple spanning trees in a network. A better routing protocol called IEEE802.1aq - Shortest Path Bridging (SPB) is recently proposed, that generates the shortest spanning tree per a destination node. As SPB provides a routing path per a destination node, there is no way to adapt network traffic at normal condition. If we are free from the principle of "a spanning tree per a destination node", we can achieve adaptive routing. Based on this philosophy, we propose a new spanning tree based protocol - Edge Node Divided Spanning Tree (ENDIST). ENDIST divides an edge node into sub-nodes as many as connecting links from the node and each sub-node generates a single shortest path tree based on SPB. Depending on network or nodal status, ENDIST chooses a better routing path by flow-basis. This added traffic engineering ability contributes to enhanced throughput and reduced delay in backbone networks. The simulation informs us that ENDIST's throughput under heavy load performs about 3.4-5.8 and 1.5-2.0 times compared with STP's and SPB's one respectively. Also, we verified that ENDIST's throughput corresponds to the theoretical upper bound at half of cases we investigated. This means that the proposed ENDIST is a dramatically enhanced and the close-to-perfect spanning tree based routing schemes.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.2
• /
• pp.136-142
• /
• 2010

In this paper, the microstrip antenna for penta-band service is proposed. It is designed for a wide band characteristic based on a monopole line combined with a triangular patch structure which has two slits. Total antenna size is $35\;mm{\times}20\;mm$ and it was fabricated on FR-4 substrate($\varepsilon_r=4.4$) which has $35\;mm{\times}75\;mm{\times}1\;mm$ size and a microstrip line with impedance 50 ohm is used. Experimental result shows the impedance bandwidth($VSWR{\leq}3$) of the proposed antenna operated within GSM/DCS/USPCS/UMTS/Bluetooth frequency band. The resonance frequency of the proposed antenna is 0.92, 1.97, 2.45 GHz and the average gain is -2.18, -0.66, -0.58 dBi. Also, the radiation efficiency is 60, 85, 87%. The fabricated antenna is satisfied with the aimed impedance bandwidth ($VSWR{\leq}3$) in GSM/DCS/ USPCS/UMTS/Bluetooth frequency band.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.18 no.5
• /
• pp.708-720
• /
• 1993

The new preventive control mechanisms for traffic management in BISDN/ATM networks can be divided into Connection Admission Control(CAC), Usage Parameter Control (UPC), and Priority Control. Of these mechanism, Usage Parameter Control continuously monitors the parameters admitted in the network's entry point to guarantee quality of service of connections already admitted. Upon detecting traffic that violates the negotiated parameter, it takes the necessary control measures to prevent congestion. Among these traffic control methods, this paper focuses on the Usage Parameter Control method, and proposes and designs GRACE-LB(Guaranteed Rate Acceptance & Control Element-using Leaky Bucket) which improves upon existing UPC models. GRACE-LB modifies the previous LB model by eliminating the cell buffer, dividing the token Pool into two pools, Long-term pool, Short-term pool, and changing the long-term token generating form using 'Cycle Token' into the same bursty form as the traffic source. Through this, GRACE-LB achieves effective control of the Average Bit Rate(ABR) and burst duration of bursty multimedia traffic which previous LB models found difficult to control. Also, since GRACE-LB can e implemented using only simple operations and there are no cell buffers in it, it has the merit of being easily installed at any place.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.47 no.2
• /
• pp.9-17
• /
• 2010

Recently, there has been much interest in orthogonal frequency division multiplexing (OFDM) for next generation wireless wideband communication systems. OFDM is a special case of multicarrier transmission, where a single data stream is transmitted over a number of lower-rate subcarriers. One of the main reasons to use OFDM is to increase robustness against frequency-selective fading or narrowband interference. However, in the radio systems it is also important to distortion introduced by high power amplifiers (HPA's) such as solid state power amplifier (SSPA) considered in this paper. Since the signal amplitude of the OFDM system is Rayleigh-distributed, the performance of the OFDM system is significantly degraded by the nonlinearity of the HPA in the OFDM transmitter. In this paper, we propose a canonical piecewise-linear (PWL) model based digital predistorter to prevent signal distortion and spectral re-growth due to the high peak-to-average power ratio (PAPR) of OFDM signal and the nonlinearity of HPA's. Computer simulation on an OFDM system under additive white Gaussian noise (AWGN) channels with QPSK, 16-QAM and 64-QAM modulation schemes and modulator/demodulator implemented with 1024-point FFT/IFFT, demonstrate that the proposed predistorter achieves significant performance improvement by effectively compensating for the nonlinearity introduced by the SSPA.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.14 no.5
• /
• pp.249-254
• /
• 2014

In this paper, minimizing of a parabolic edge planar monopole antenna by scaling method is presented. With the aid of a matching step and discontinuous CPW, the antenna easily adjusts the impedance matching. We used an FR4 dielectric substrate with a dielectric constant of 4.4. The dimensions of the antenna are $26mm{\times}31mm{\times}1.6mm$. A return loss value of more than 10dB was found in the 2.37GHz to 10.52GHz (8.15GHz) range of the antenna fed by the discontinuous CPW. The radiation pattern is about the same as that of the dipole antenna at all frequencies. Configuration elements of the antenna except feed part were reduced into the same rate. So, the size of the antenna was decreased and a broadband property was maintained. Therefore, the self-complementary characteristic of the antenna was confirmed. While satisfying the UWB band, having the smallest size in the antenna miniaturized by scaling;when scale was 0.6. The dimensions of the antenna are $15.6mm{\times}18.6mm{\times}1.6mm$. The return loss was more than 10 dB of the measured result in the range of 3.07GHz to 12.59GHz (9.52GHz).

• The Proceeding of the Korean Institute of Electromagnetic Engineering and Science
• /
• v.13 no.1
• /
• pp.51-62
• /
• 2002

EMI/EMS 측정을 위해서는 주변 전자파 잡음(background noise)이 낮은 야외시험장(Open Area Test Site)이 가장 바람직하나, 근래 전자(전기 기기 사용의 증가와 방송.무선통신 시스템의 다양화로 인한 인공잡음(artificial noise)의 증대로 조건에 부합된 부지 선정이 어렵고, 설치 비용이 매우 크며 날씨 변화에 따라 시험 계획이 변경 될 수도 있는 단점이 있다. 전자파 분-무반사실(Semi Anechoic Chamber)은 대부분의 환경 잡음을 감쇠시키므로 야외시험장처럼 장소의 구애를 받지 않아 도시나 혹은 제품 생산지 가까이에 설치 운용이 가능하다. 그러나 큰 설치 공간과 많은 시설 유지 비용을 필요로 하며, 저주파 대역에서는 반사에 의한 공진을 완전히 제거할 수 없어 성능이 떨어진다. 또한, 최근 컴퓨터 CPU의 동작주파수가 급속하게 높아지고 PCS, IMT-2000 등과 같은 이동전화의 사용주파수도 계속해서 높아짐에 다라 미연방통신위원회(Federal Communication Commission)에서는 5㎓까지의 복사 방출 시험을 요구하고 있다. IEC 61000-4-3 복사 내성 시험규격도 휴대폰 주파수인 2㎓까지 확장되었으며 IMT-2000, Bluetooth 등 새로운 이동통신서비스가 속속 개발됨에 따라 18㎓ 까지 시험 주파수가 확장되는 추세이다. 그러나, 현재 국내 각 연구실에서 보유하고 있는 야외시험장이나 전자파 반-무반사실의 경우 1㎓이상에서의 시험이 곤란하여 수 ㎓주파수대역에서 시험이 가능한 복사 및 내성시험 시설이 필요하게 되었다. 이러한 문제점들을 해결하기 위해 고안된 대용 측정 시설 중 대표적인 것이 TEM 셀이나 GTEM셀과 같은 TEM 도파관(waveguide) 형태의 장비들이다. 이들은 본래 EMS 측정을 위한 장비이지만 협소한 공간이나 외부와의 전자파 간섭의 우려가 없고, 설치가 비교적 자유로워 여러 연구기관에서 도파관 원리를 이용한 측정 방식을 연구(개발하여 범용적인 전자파 적합성 측정 장비로서 활용하고 있다. 야외시험장과 무반사실 등이 안테나에 의한 피시험기기 주변 공간에서의 1점 측정으로 인해 시험 시간이 많아 소요되는 공통적인 단점이 있는 반면, TEM 도파관에 의한 측정은 일단 피시험기기의 모델링 정보만 얻어지면 계산에 의해 EMI 측정을 바로 할 수 있다. <표 1>에서 현재 상용화되어 사용되고 있는 TEM/GTEM 셀, 야외 시험장 및 전자파 무반사실에 대해 EMI 측정과 관련된 몇 가지 사안에 대해 비교하였다. 본 문서에서는 야외시험장이나 전자파 반-무반사실 등과 같은 기존 EMI/EMS 측정 시설의 단점을 보완하고, 광대역 특성을 갖는 대용 측정 시설로서의 TEM 도파관에 대해 소개하고 야외시험장 결과와의 상관관계 알고리즘 및 표준화 동향에 대해 기술하였다. 2절에서는 대표적인 TEM 도파관 구조의 측정 시설인 TEM 셀과 GTEM 셀의 전기적.구조적 특징에 대해 간단히 기술하고, 3절에서는 TEM 셀과 GTEM 셀에서이 측정결과를 이용하여 야외 시험장 결과를 얻어내는 상관관계 알고리즘에 대해 기술하였다. 4절에서는 IEC/CISPR와 TC77에서의 표준화 활동을 중심으로 현재 진행중인 TEM 도파관 관련 표준화 동향과 내용에 대해 기술하고자 한다.

• Journal of Korea Multimedia Society
• /
• v.1 no.1
• /
• pp.45-55
• /
• 1998

In the tele-medical system, the broadband network for multimedia telecommunication and the multimedia terminal equipment for the remote access of the tele-medical information are essential. Especially, the tele-medical terminal equipment should provide the multimedia GUI environment in order to support the similar medical process by the tele-medical system. In this paper, we present a multimedia GUI (Graphic User Interface) for a Multimedia Tele-Medical System (TeleMedi_GUI) based on ATM/B-ISDN. In the tele-medical system, one workstation is used for the multimedia data server that is supporting multiple client terminals that are connected by the ATM network. The client terminals are based on Multimedia Personal Computers, and provide the remote access environment of the tele-medical database. We also developed the remote access protocols among the clients and the server to access multimedia medical information of the multimedia server. With using the TeleMedi_GUI, the doctors can examine and treat patients efficiently, using image data like X-ray/CT and voice data such as the S-ray diagnosis. The result of this paper can be applied to the following areas: 1) the implementation of the advanced medical service system interconnecting the small-scale health center and general hospitals, 2) the development of a fully computerized medical information system within the hospital.