본 논문은 노약자들의 발목근력보조를 위한 착용형 로봇에 대해서 서술하였다. 기존 착용형 로봇들은 보행 시 필요한 근력을 보조하기 위해 대부분 모터와 감속기를 사용하였다. 하지만 모터와 감속기의 조합은 무게가 무거울 뿐만 아니라 감속기 치차의 마찰때문에 실제 사람의 근육과 달리 강성과 토크를 동시에 제어하기 어려운 한계가 있다. 따라서 본 연구에서는 모터/감속기 조합보다 가볍고 안전하며 근력을 보조하는 힘을 충분히 발휘할 수 있는 Mckibben 공압 근육을 사용하였다. 발목의 피칭 모션에 이용되는 종아리 가자미근 및 앞정강근의 힘을 한 쌍의 공압 근육을 사용한 상극구동으로 보조하였으며, 상극구동제어를 위해 상극구동 모델 파라미터들을 실험적으로 도출하였다. 사용자의 보행의지를 판단하고자 발바닥에 부착된 압력변위센서로 압력과 압력중심위치를 측정하여 발바닥의 하중과 발목토크를 계산하였고, 이를 기반으로 공압 근육 관절의 강성과 토크를 동시에 제어하였다. 최종적으로, 트레드밀에서 근전도 신호를 측정하여 발목근력보조로봇의 성능을 실험적으로 입증하였다.
본 논문은 대퇴 절단 환자를 위한 의지를 설계하고 최적화를 통해 경량화하는 것을 목적으로 한다. 대퇴절단환자의 경우 정상적인 보행을 위해서는 무릎 관절의 움직임을 모사하는 것이 무엇보다 중요하다. 따라서 무릎 관절 움직임을 모사할 수 있는 1자유도의 능동형 대퇴 의지를 설계하였다. 3개의 링크들로 이루어진 기구학 식을 통해 능동형 대퇴 의지의 작동범위 및 토크를 계산하였다. 또한 의지를 구성하는 주요 부품에 대한 유한요소해석을 통해 작동 환경에서의 안정성을 검증하고 최적화 기법을 통해 중요 부품의 경량화를 진행하였다. 동일한 조건에서 형상최적화를 수행하여 안정성을 확보하면서 최소부피를 가지는 형상을 구현하였다. 해석 결과를 통해 주요 부품의 경우 약 35%정도 무게가 감소한 것을 확인할 수 있다.(abstract)와 동일한 내용으로 국문으로 작성하시면 됩니다. 본 논문은 생체신호를 기반으로 하여 노약자들이 사용할 수 있는 재활기기들의 훈련 프로그램 및 데이터 관리에 대한 것이다. 노약자의 신체조건, 취향에 대한 기능적, 감성적 특성을 반영하여 개발된 프로그램으로서 남녀 구분이 되어 있다. 65세 이상의 노약자 20명을 대상으로 수행한 일련의 실험을 통하여 프로그램의 신뢰성과 우수성을 확인하였다.
Ankle-foot orthosis with a pneumatic rubber actuator, which is intended for the assistance and the enhancement of ankle muscular activities was developed. In this study, the effectiveness of the system was investigated during plantarflexion motion of ankle joint. To find a effectiveness of the system, the subjects performed maximal voluntary isokinetic plantarflexion contraction on a Biodex-dynamometer. Plantarfexion torque of the ankle joint is assisted by subject's soleus muscle that is generated when ankle joint do plantarflexion motion. We used the muscular stiffness signal of a soleus muscle for feedback control of ankle-foot orthosis as physiological signal. For measurement of this signal, we made the muscular stiffness force sensor. We compared a muscular stiffness force of a soleus muscle between with feedback control and without it and a maximal plantarflexion torque between not wearing a ankle-foot orthosis, without feedback control wearing it and with feedback control wearing it in each ten elderly adults. The experimental result showed that a muscular stiffness force of a soleus muscle with feedback control was reduced and plantarflexion torque of an ankle joint only wearing ankle-foot orthosis was reduced but a plantarflexion torque with feedback control was increased. The amount of a increasing with feedback control is more higher than the amount of a decreasing only wearing it. Therefore, we confirmed the effectiveness of the developed ankle-foot orthosis with feedback control.
최근 산업현장에서 작업자들의 장시간 작업으로 인한 사고 및 부상의 위험을 방지하기 위하여 작업자들의 근력을 보조할 수 있는 외골격 근력보조 장치에 대한 연구가 활발히 진행되고 있다. 그러나 기존의 외골격 장치들은 작업자의 근력을 보조하기 위하여 모터의 동력을 사용하므로, 고가일 뿐만 아니라 오작동의 위험이 있어서 산업현장에서 매우 제한적으로 사용되었다. 이러한 문제를 해결하기 위해서, 본 연구에서는 센서 및 모터 없이 순수 기계요소들만으로 구성된 근력보조 외골격 장치를 설계 및 제작하였다. 본 외골격 장치는 사람의 손목 관절을 제외한 어깨, 팔꿈치 관절의 동작이 추종 가능하며, 팔의 자중에 의한 중력토크를 상쇄 가능한 중력보상장치를 탑재하여 작업자의 팔에 대한 근력보조를 수행한다. 개발된 외골격 장치의 성능을 검증하기 위하여 EMG 센서를 이용한 근전도 비교 실험을 수행하였고, 실험 결과를 바탕으로 외골격 장치의 근력보조 성능을 확인하였다.
계단 보행 시 로봇의 최적 궤도 계산은 유전자 알고리즘과 계산 토크 컨트롤러를 사용하여 수행되었다. 첫째, 생식, 교배, 돌연변이로 이루어진 실시간 유전 알고리즘 (RCGA)을 사용하여 총 에너지 효율이 최소화되었다. 보폭의 시작과 끝, 그리고 조인트, 각도, 각속도 위치 어셈블리 관련 재현성 조건은 선형 제약이다. 다음은 고르지 못한 제약은 코너 스윙 다리와 계단의 외부와의 충돌을 막기 위한 조건, 운동 학적 특이성을 막기 위한 무릎 관절의 조건 및 진행 방향의 안전은 보장되지 않음 이란 조건을 따른다. 마지막으로, 각 관절의 각도 궤도는 염색체를 근사 계수를 가지는 4차 다항식에 의해 정의된다. 이것은 보통 도보를 의미한다. 이 연구에서는 최적의 궤도의 에너지 효율을 7개의 링크로 구성된 7자유도의 2족 로봇을 통한 컴퓨터 시뮬레이션을 통해 분석했다.
Ankle-foot orthosis with an artificial pneumatic muscle which is intended for the assistance of plantarfelxion torque was developed. In this study, power pattern of the device in the various pneumatics and the effectiveness of the system were investigated. The pneumatic power was provided by ankle-foot orthosis controlled by user‘s physiological signal, that is, muscular stiffness in soleus muscle. This pneumatic power can assist plantarflexion torque of ankle joint. The subjects performed maximal voluntary isokinetic plantarflexion motion on a biodexdynamometer in different pneumatics, and they completed three conditions: 1) without wearing the orthosis, 2) wearing the orthosis with artificial muscles turned off, 3) wearing the orthosis activated under muscular stiffness control. Through these experiments, we confirmed the effectiveness of the orthosis and muscular stiffness control using the analyzing isokinetic plantarflexion torque. The experimental results showed that isokinetic torques of plantarflexion motion of the ankle joints gradually increased in incremental pneumatic. The effectiveness of the orthosis was -7.26% and the effectiveness of the muscular stiffness control was 17.83% in normalized isokinetic plantarflexion torque. Subjects generated the less isokinetic torques of the ankle joints in wearing the orthosis with artificial muscles turned off, but isokinetic torques were appropriately reinforced in condition of wearing the orthosis activated under muscular stiffness control(17.83%) compared to wearing the orthosis(-7.26%). Therefore, we respect that developed powered orthosis is applied in the elderly that has weak muscular power as the rehabilitation equipment.
본 연구에서는 스미스 머신을 이용한 스쿼트 운동에 대한 가상 테스트 프레임웍을 제안하고 구현하였다. 이를 위하여 인체 및 제품의 통합 모델을 개발하고, 실험 데이터를 바탕으로 자세의 변화에 따른 새로운 동작을 생성하는 알고리즘을 개발한 후, 가상의 조건에서 동작을 생성하여 인체의 관절에 걸리는 토크와 근육에 걸리는 힘을 시뮬레이션 하는 전체 시스템을 개발하였다. 이 시스템을 검증하기 위하여 동작 수집과 더불어 EMG와 지면반력에 대한 데이터를 수집하여 시뮬레이션 결과가 실제와 잘 맞는지 확인하였다. 이 시스템을 확장시켜 사용한다면 다양한 조건에서 운동하였을 때 신체 근육과 관절에 어떤 영향을 끼치는 지 시뮬레이션 해봄으로써 적절한 운동 프로그램을 효과적으로 개발할 수 있을 것으로 기대된다.
Recently, skid steering methods have been increasingly applied to unmanned ground vehicles since they can provide a narrow turn that general steering methods like ackerman steering may not provide. However, dynamic behaviors of the skid steering vehicles with articulating arms which occur during a steering are very complicated and coupled. This makes it difficult to control vehicles and in severe case vehicles may loose stability. There are two methods to control unmanned ground vehicles. The first one is speed control method generally used with easiness and robustness in remote vehicle control. The next one is torque control allowing the vehicles to get better performance in several cases provided careful application is achieved. This paper addresses dynamic phenomena of skid steering vehicles during steering and compares with vehicle driving control methods between torque(traction force) control and speed control.
The purpose of this study was to investigate the effects of strength training on knee joint torque during walking in an adolescent with trisomy-21 Down syndrome. One adolescent with Down syndrome and one normal child participated in this study. Strength training consisted of eight exercises: squat, hamstring curl, hip adduction, hip abduction, knee extension, toe raise, sit-ups, and hyperextension of the waist. The participant with Down syndrome was participated in strength training for 12 weeks, three times a week, three sets, 10-15 RM; resistance was adjusted according to the principle of progressive overload. To measure the effect of strength training, isokinetic strength variables and knee joint torques were measured before training and after 12 weeks of training. The participant with Down syndrome had some abnormalities in controlling knee motion during walking due to muscle hypotonia, ligament laxity, and weakness of muscles. Post-training isokinetic strength increased compared to pre-training measurements. Knee range of motion were increased after strength training. Strength training did not affect ad/adduction and in/exteranl moments but did have an effect on flexor/extensor moment and timing.
Various methods and torque generating devices are developed and employed to apply proper torque clinically. In this study, clinically used torque control devices are measured whether uniformed and precise torque are generated. Digital torque gauge are employed for measurement and torque driver, torque limiting device, torque indicating device are used for torque generating devices. ${\chi}^2$ distribution was formed and One-way ANOVA(Turkey test) was performed to measure torque values generated by each torque generating device. In the results, all companies have been shown slight errors and deviations. This indicates a difficulty of applying precise torque. Therefore, it would be recommended torque generating device should be checked whether uniformed and precise torque can be generated and an error should be corrected.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.