• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.26 no.3C
• /
• pp.201-207
• /
• 2006

Soil tests are generally conducted using a membrane to measure a pore water pressure. However, it has also been recognized that the membrane penetrates into the specimen by the change of the confining pressure, and it results in the erroneous measurement in the pore water pressure and the volumetric strain. This study examined the effectiveness of the correction equation of the membrane penetration on the basis of the experimental data acquired during the isotropic unloading and the cyclic shear process using the hollow cylindrical shear test equipment. The results showed that the membrane penetration by the correction equation could be overestimated when the mean effective stress was lower than 20kPa in this study. The limitations originated from the sudden increase near the zero effective stress, and in order to prevent the overestimation in low effective stress condition, the use of the constant a was proposed in this study. Furthermore, the correction equation for the membrane penetration had to be applied carefully when the initial relative density was high and the density changes were occurred by the relocation of the soil particle by the liquefaction.

• Journal of the Korean Geotechnical Society
• /
• v.23 no.7
• /
• pp.17-25
• /
• 2007

Various geotechnical problems due to insufficient bearing capacity or excessive settlement are likely to occur when constructing roads or large complexes on soft ground. Accurate predictions of the magnitude of settlement and the consolidation time provide numerous options of ground improvement methods and, thus, enable to save time and expense of the whole project. Asaoka's method is probably the most frequently used one for settlement prediction and the empirical formulae such as Hyperbolic method and Hoshino's method are also often used. To find an elaborate method of predicting the embankment settlement, two recurrent type neural network models, such as Jordan model and Elman-Jordan model, are adopted. The data sets of settlement measured at several domestic sites are analyzed to obtain the most suitable model structures. It was shown from the comparison between predicted and measured settlements that Jordan model provides better predictions than Elman-Jordan model does and that the predictions using CPT results are more accurate than those using SPT results. It is believed that RNN using cone penetration test results can be a highly efficient tool in predicting settlements if enough field data can be obtained.

• International Journal of Highway Engineering
• /
• v.14 no.3
• /
• pp.49-58
• /
• 2012

In many countries including Korea, the design concept of pavement structure has been converted from empirical method to mechanisticempirical method since the advent of compaction control based on resilient modulus proposed by AASHTO in 1986. Studies of last decades indicates that the classical compaction control method based on relative compaction and plate bearing test(PBT) will necessarily move to the methods taking advantage of light falling weight deflectometer(LFWD) and dynamic cone penetrometer(DCP) in addition to PBT. In this study, the validity of resilient modulus prediction equation proposed by Korean Pavement Design Guide is verified by comparison with physical properties of subgrade soil and the results of structural analysis. In addition, correlational equations between elastic modulus measured by various field tests and resilient modulus estimated by empirical model are proposed. Finally, a field test-based compaction control procedure for subgrade is suggested by using proposed correlational equations.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.28 no.2C
• /
• pp.95-103
• /
• 2008

Seismic piezocone penetration tests (SCPTu) can be used to obtain dynamic properties of soils as well as cone resistance and penetration pore pressure. However, the SCPTu system can be hardly utilized in marine soils because it is difficult to install the source apparatus which generates the shear wave in offshore site. The authors developed an inhole type piezocone penetration test (CPTu) equipment which both source and receiver composed of bender elements were installed inside the rod located behind the cone. Therefore, it can be applicable to even an offshore site without any additional source apparatus. The objective of this paper is to investigate the practical application of inhole type CPTu by performing laboratory model tests using kaolinite as soft clay. The shear wave velocities of kaolinite soil were measured with time, and the effects of soil disturbance due to the installation of source and receiver were also examined for various distance between source and receiver.

• Journal of the Korean Geotechnical Society
• /
• v.18 no.4
• /
• pp.45-53
• /
• 2002

There are some previous studies on the determination wave equation soil constants by SPT. However, methods suggested in previous researches had such analytical defects as the non-uniqueness of solutions, long-time consuming in computation, and lacking of accuracy due to the limit of available point values in time domain. In this paper, a modified procedure is proposed to improve the accuracy of determination of wave equation soil constants. It is based upon the least-error approach which minimizes the sum of errors between the measured and the recalculated wave values in total time domain. Finally, its applicability was verified by analyzing measured data presented on the released references.

• Geotechnical Engineering
• /
• v.14 no.4
• /
• pp.163-176
• /
• 1998

To apply piezocone test to soil classification, several classification charts based on correlations between its results and basic characteristics of soils have been developed. However, it is necessary to investigate their applicability to Korean soil, since they were the results obtained from the limited number of foreign sites. In this study, 41 piezocone penetration bests for various sixtes spreading widely over Korean territory were carried out. Correlations between piezocone teat results and basic characteristics and the applicability of existing classification charts were investigated. Conclusively, new classification charts based, on Unified Soil Classification System were developed with a local confidence.

• Journal of Korean Society of Rural Planning
• /
• v.5 no.1 s.9
• /
• pp.95-103
• /
• 1999

The purpose of this study is to find out the distribution of underground biomass and its soil stabilizing effects. Bamboo and grass were examined and compared. 1. Thirty 'soil & root' samples were collected to the depth of 30cm with Impact-corer, and then divided into three sections(0-10cm, 10-20cm, 20-30cm). Each piece had a volume of $950cm^3$ and the underground biomass was separated from the soil particles by washing with flowing water. The average underground biomass rates of bamboo and grass were 10.8% and 4% of each sample, respectively. The rate of grass root biomass declined with depth, but the bamboo root biomass was at peak at around 20cm depth. 2. The shear strength was measured with con-penetration tester at each sample collecting site. Three measurements were made at each depth(0-10cm, 10-20cm, 20-30cm) and were compared with the impact counts needed to insert the corer to the depth of 30cm. The shear strength has clear correlations with underground biomass. The more underground biomass, the higher shear strength. The shear strength of bamboo was about three times larger than the grass.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.30 no.1
• /
• pp.127-134
• /
• 2024

With the growth of offshore wind power generation market, the corresponding installation vessel market is also growing. It is anticipated that approximately 100 installation vessels will be required in the of shore wind power generation market by 2030. With a price range of 300 to 400 billion Korean won per vessel, this represents a high-value market compared to merchant vessels. Particularly, the demand for large installation vessels with a capacity of 11 MW or more is increasing. The rapid growth of the offshore wind power generation market in the Asia-Pacific region, centered around China, has led to several discussions on orders for operational installation vessels in this region. The seabed geology in the Asia-Pacific region is dominated by clay layers with low bearing capacity. Owing to these characteristics, during vessel operations, significant spudcan and leg penetration depths occur as the installation vessel rises and descends above the water surface. In this study, using penetration variables ranging from 3 to 21 m, the unique vibration period, structural safety of the legs, and conductivity safety index were assessed based on penetration depths. As the penetration depth increases, the natural vibration period and the moment length of the leg become shorter, increasing the margin of structural strength. It is safe against overturning moment at all angles of incidence, and the maximum value occurs at 270 degrees. The conditions reviewed through this study can be used as crucial data to determine the operation of the legs according to the penetration depth when developing operating procedures for WTIV in soft soil. In conclusion, accurately determining the safety of the leg structure according to the penetration depth is directly related to the safety of the WTIV.

• Journal of the Korean Geotechnical Society
• /
• v.31 no.3
• /
• pp.63-72
• /
• 2015

This paper describes the correlation and relationship between elastic moduli measured by three stiffness measurement methods with different mechanical characteristics to evaluate the compaction characteristics of subgrade soils. The Soil Stiffness Gauge (SSG) with very small strain (${\approx}0.001%$) ranges, static Plate Loading Test (PLT) with mid-level strain (${\approx}0.01{\sim}0.1%$) ranges, and Dynamic Cone Penetrometer (DCP) using penetration resistance were implemented to measure the elastic modulus. To use the elastic modulus measured by different measurement methods with a wide range of strain in practice, it is required to identify the correlation and relationship of measured values in advance. The comparison results of the measured elastic moduli ($E_{SSG}$, $E_{PLT}$, $E_{DCP}$) using the three measurement methods for domestic and overseas subgrade soils under various conditions indicate that the evaluated elastic modulus relies on the types of soils and the level of stress condition. The correlation analysis of the measured elastic moduli except the data of cement treated soils indicates that the static elastic modulus ($E_{PLT}$) is evaluated as about 60 to 80% of the dynamic elastic modulus ($E_{SSG}$). Unusual soils such as cement treated soils are required to be corrected by the stress correction during the correlation analysis with typical soils, because these types of soils are sensitive to the stress condition when measuring the static elastic modulus ($E_{PLT}$) of soils. In addition, when considering the use of DCP data for the evaluation of the elastic modulus ($E_{DCP}$), the measured data of the elastic modulus less than 200 MPa show more reliable correlation.

• Journal of the Korean GEO-environmental Society
• /
• v.6 no.2
• /
• pp.5-14
• /
• 2005

In the present study, the liquefaction potential in the area of the Incheon international airport was assessed by applying the data of both standard penetration tests and laboratory tests to the modified Seed & Idriss method. The analysis was performed against the non-plastic silty soil layer and silty sand soil layer existing within the depth of 20m and under the ground water level, having the standard penetration value(N) of below 20. Also, each set of data was mapped using the GIS(Geographic Information System) and the safety factor against the liquefaction potential ($FS_{liquefaction}$) was obtained by overlapping those layers. Throughout the analysis, it was found that there exists a potential hazard zone for the liquefaction, showing partially that the safety factor against the liquefaction potential is 1.0 to 1.5 below the standard safety factor criterion. It is further thought to be necessary that the liquefaction potential for the corresponding hazard zone be additionally assessed in detail.