• Korean Journal of Optics and Photonics
• /
• v.6 no.3
• /
• pp.214-221
• /
• 1995

When the broad pressure region (0.5-3.5 atm) of laser media is pumped by 70 ns [FWHM] electronbeam accelerator (800 kV, 21 kA), the correlation between free-runnuing XeF$(C\rightarrowA$ excimer laser output and Xe concentration are studied. The resonator consisted of dichroic output coupler, and the laser output is optimized with laser media $(Xe/F_2/Ar)$ as functions of total pressure and gas mixing ratio. Under the condition of F2 0.46% fixed, the laser intrinsic efficiencies of 0.38%, 1.03%, and 0.29% are obtained at 1. 2, and 3 atm, respectively. So then the peaks of laser intrinsic efficiency occured to the higher Xe concentration with decreasing total gas pressure. By analyzing the kinetics for the $XeF^*(C)$ formation efficiency and XeF$(C\rightarrowA$ laser extraction efficiency the dependence of Xe concentration on their correlation is explained. As the results we propose efficient operation of an atmosphericpressure XeF$(C\rightarrowA$ laser. laser.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.22 no.3
• /
• pp.292-298
• /
• 2011

In this paper, a voltage controlled injection-locked oscillator(VC-ILO) is proposed for wideband applications. From the control of the free-running frequency by a varactor diode, the wide frequency locking range can be obtained for low-level injected signals. The proposed VC-ILO is implemented on an FR-4 substrate with a thickness of 0.8 mm. The free-running frequencies of the oscillator is 2.39~2.52 GHz at the control voltage of 0~5 V. While the frequency locking range of over 50 MHz is presented for -10 dBm injected signal level at a fixed frequency, the locking range of over 90 MHz can be achieved for -30 dBm by controlling the free-running frequency.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.44 no.12
• /
• pp.43-53
• /
• 2007

We have analyzed low current operation characteristics of a VCSEL transmitter operating at fixed Current over wide temperature range. Used 850 nm oxide VCSEL has low temperature dependence of the threshold current and $d^2I_{th}/dT^2$ is approximately $1.346\times10^{-4}mA/^{\circ}C^2$. We fixed on-current so that output power from the chip is 1 mW at $20^{\circ}C$ and investigated the turn-on, turn-off characteristics and eye-diagram of the 850 nm oxide VCSEL transmitter with varying ambient temperature and off-current. We measured rise time, fall time, extinction ratio and timing jitter by changing tile ambient temperature and off-current. With the fixed off-current of around $0.1\sim0.2mA$ lower than the lowest threshold current the transmitter successfully operated at 1.25 Gbps over a wide temperature range from $-20^{\circ}C$ to $80^{\circ}C$.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.20 no.6
• /
• pp.570-579
• /
• 2009

In this paper, we presented a Vt-DRO with a wide electrical frequency tuning range, using open-loop gain method. The Vt-DRO was composed of 3-stages, resonator, amplifier and phase shifter. In order to satisfy an oscillation condition, we determined magnitude and phase of each stage. The measured S-parameter of cascaded 3-stages shows open-loop oscillation condition. Also, using measured open loop group delay, we derived the relation for electrical frequency tuning range. The Vt-DRO was implemented by connecting the input and the output of the designed open-loop and resulted in closed-loop. As a results, tuning-range of Vt-DRO is 82 MHz, which is close to the predicted results for tuning voltage 0${\sim}$10 V and shows linear frequency tuning at the center frequency of 5.3 GHz. The phase noise is -104 ${\pm}$1 dBc/Hz at 100 kHz offset frequency and power is 5.86${\pm}$1 dBm respectively.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.27 no.2C
• /
• pp.191-200
• /
• 2002

A frequency synthesizer that can be used in IMT-2000 was designed and fabricated using dual loop PLL(Phase Locked Loop) in this paper. For improving phase noise characteristic two loops, reference loop and main loop, were divided. Phase noise was improved by transformed clamp type voltage controled oscillator and optimizing loop bandwidth in reference loop. And voltage controlled oscillator open loop gain in main loop. Fabricated the frequency synthesizer had 1.81GHz center frequency, 160MHz tuning range, 13.5dBm output power and -119.73dBc/Hz low phase noise characteristic.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.14 no.2
• /
• pp.111-118
• /
• 2003

Notch Antenna is a travelling wave type antenna and can provide multioctave operation in phased arrays that scan over wide angle. In this paper, we designed a wideband E-plane phased array antenna using E-plane waveguide simulator which has a bandwidth of 3 : 1 and a scan volume of $\pm$45$^{\circ}$ in E-plane. We compared impedance of single antenna and infinite array antenna using equivalent circuit modeling. We analyzed full structure of 1$\times$9 phased array antenna and we evaluated active reflection coefficient with variation of beam scan angle through mutual coupling coefficient acquired from simulation and investigated the variation of antenna gain with variation of active element pattern as beam scan angle is varied.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.15 no.11
• /
• pp.1075-1081
• /
• 2004

In this paper, a VCO of a general advance warning system for vehicle's speed limitation in the X-band used in Japan is designed using a small signal scattering coefficient of PHEMT. A varactor diode that wide tuning range and series resistance 0 H is used for designing the VCO and -85 dBc/Hz of phase noise at 10 kHz of offset frequency is obtained by adjusting the reflection coefficient between the micro-strip line and the varactor device which determines transistor's operation voltage and resonant frequency, In addition +4.5 dBm of basic frequency signal output level and -25.6 dEc of the second harmonic constraint are acquired. Sample that produce in this paper could confirm that more excellent special quality appears than existing products in sensitivity.

• Journal of Sensor Science and Technology
• /
• v.8 no.1
• /
• pp.16-23
• /
• 1999

When a moving piezoelectric transducer detects an object in water, its receiving sensitivity is attenuated by Doppler effect. In this paper, a method for compensating the effect is suggested by using a newly designed condenser of which capacitance is varied according to the moving speed of the transducer. Using the method, the receiving resonant frequency of the transducer can be changed automatically. As a result, there is good agreement between the results of experiment and those of calculation. It is confirmed that the response sensitivity degradation of transducers due to Doppler effect can be compensated in the range of $1{\sim}10^m/_s$ moving speed.

• Polymer(Korea)
• /
• v.27 no.3
• /
• pp.189-194
• /
• 2003

Interfacial evaluation, damage sensing and cure monitoring of single carbon fiber/thermo setting composite with different curing processes were investigated using electro-micromechanical test. After curing, the residual stress was monitored by measurement of electrical resistance and then compared to various curing processes. In thermal curing case, matrix tensile strength, modulus and interfacial shear strength were higher than those of ultraviolet curing case. The shrinkage measured during thermal curing occurred significantly by matrix shrinkage and residual stress due to the difference in thermal expansion coefficient. The apparent modulus measured in the thermal curing indicated that mechanical and interfacial properties were highly improved. The reaching time to the same stress of thermal curing was faster than that of UV curing case.

• Journal of Korea Multimedia Society
• /
• v.14 no.2
• /
• pp.194-200
• /
• 2011

Recently, RFID(Radio Frequency IDentification) market spread in industry region is entering a phase of stagnation due to cost issue. RFID tag inlay cost has become relatively more expensive due to the recent decrease in chip price. Therefore, a simple and rapid design technique for RFID tag has yet to be implemented to achieve low cost. This paper presents a design technique considering chip impedance for antenna design for improved accuracy and computation time. As a result, it is confirmed that analysis error for resonance ranges within 20MHz and readable range error falls within 1.5m.