• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.43 no.12 s.354
• /
• pp.15-22
• /
• 2006

In this paper, 1.8V 8-bit 500MSPS Low-power CMOS Digital-to-Analog Converter(DAC) for UWB(Ultra Wide Band) Communication Systeme is proposed. The architecture of the DAC is based on a current steering 6+2 full matrix type which has low glitch and high linearity. In order to achieve a high speed and good performance, a current cell with a high output impedance and wide swing output range is designed. Further a thermometer decoder with same delay time and low-power switching decoder for high efficiency performance are proposed. The proposed DAC was implemented with TSMC 0.18um 1-poly 6-metal N-well CMOS technology. The measured SFDR was 49dB when the output frequency was 50MHz at 500MS/s sampling frequency. The measured INL and DNL were 0.9LSB and 0.3LSB respectively. The DAC power dissipation was 20mW and the effective chip area was $0.63mm^2$.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.53 no.7
• /
• pp.17-26
• /
• 2016

This work proposes a 12b 60MS/s 0.18um CMOS Flash-SAR ADC for various systems such as wireless communications and portable video processing systems. The proposed Flash-SAR ADC alleviates the weakness of a conventional SAR ADC that the operation speed proportionally increases with a resolution by deciding upper 4bits first with a high-speed flash ADC before deciding lower 9bits with a low-power SAR ADC. The proposed ADC removes a sampling-time mismatch by using the C-R DAC in the SAR ADC as the combined sampling network instead of a T/H circuit which restricts a high speed operation. An interpolation technique implemented in the flash ADC halves the required number of pre-amplifiers, while a switched-bias power reduction scheme minimizes the power consumption of the flash ADC during the SAR operation. The TSPC based D-flip flop in the SAR logic for high-speed operation reduces the propagation delay by 55% and the required number of transistors by half compared to the conventional static D-flip flop. The prototype ADC in a 0.18um CMOS demonstrates a measured DNL and INL within 1.33LSB and 1.90LSB, with a maximum SNDR and SFDR of 58.27dB and 69.29dB at 60MS/s, respectively. The ADC occupies an active die area of $0.54mm^2$ and consumes 5.4mW at a 1.8V supply.

• Journal of KIISE
• /
• v.44 no.2
• /
• pp.213-222
• /
• 2017

The Internet of Things (IoT) technology is rapidly developing in recent years, and is applicable to various fields. A smart factory is one wherein all the components are organically connected to each other via a WSN, using an intelligent operating system and the IoT. A smart factory technology is used for flexible process automation and custom manufacturing, and hence needs adaptive network management for frequent network fluctuations. Moreover, ensuring the timeliness of the data collected through sensor nodes is crucial. In order to ensure network timeliness, the power consumption for information exchange increases. In this paper, we propose an IEEE 802.15.4e DSME-based distributed scheduling algorithm for mobility support, and we evaluate various performance metrics. The proposed algorithm adaptively assigns communication slots by analyzing the network traffic of each node, and improves the network reliability and timeliness. The experimental results indicate that the throughput of the DSME MAC protocol is better than the IEEE 802.15.4e TSCH and the legacy slotted CSMA/CA in large networks with more than 30 nodes. Also, the proposed algorithm improves the throughput by 15%, higher than other MACs including the original DSME. Experimentally, we confirm that the algorithm reduces power consumption by improving the availability of communication slots. The proposed algorithm improves the power consumption by 40%, higher than other MACs.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.16 no.5 s.96
• /
• pp.482-487
• /
• 2005

In this paper, we propose the control method of output impedance of each cascode unit cell of distributed amplifier by connecting varactors in the gate-terminal of common gate. Compared to common source unit cell, cascode unit cell has many advantages such as high gain and high output impedance as well as negative resistance loading. But if the transistor model which is used in design is inaccurate and process parameter is changed, oscillation sometimes can occur at band edge in which the gain start to drop. Therefore, we need control circuit which can prevent oscillation, although the circuit has already fabricated, and varactor connected to gate-terminal of common gate of cascode gain cell can play that part. Measured result of fabricated distributed amplifier shows the capability of contol of gain characteristic by adjusting of value of varactors, this can guarantee the stability of the circuit. The gain is $8.92\pm0.82dB$ over 49 GHz, the group delay is $\pm9.3 psec$ over 41 GHz. All transistor which has $0.15{\mu}m$ gate length is GaAs based p-HEMT, and distributed amplifier is put together with 4 stages.

• Journal of Food Hygiene and Safety
• /
• v.15 no.4
• /
• pp.304-314
• /
• 2000

Following the recent policy, enlargement of foodservice and contracted management systems of high school foodservices have been accelerated, and the scales of foodservices have been gradually increased. A sudden growth of domestic foodservice companies have remarkably disparated. Yet compared to that of the foodseuice control in advanced countries, domestic foodservice control has a lot more to learn. Due to the characteristics of foodservice establishment serving many people at a time, there is always a high potential of food bone outbreak. The purpose of this study was to evluate hazard factors in the steps of production, holding and assembly and service of fried curry hair-tail, cold seaweed and cucumber, fried pork cutlet, that were served by contracted management in high school foodservice centre, then to suggest method of control with the Hazard Analysis Critical Control Point(HACCP) program. Also we suggested the possibility that the contracted management of foodservice system can be established and utilized to identify the variation of holding temperature among floods up to 6 hours after cooking. The results are as follows; The hazard factors in food product had come from the temperature, time, pH, Aw, equipment and utensils. The critical control point(CCP) of each food product; curry hair-tail, cold seaweed and cucumber and pork cutlet was cooked and held before serving, prepared and held before serving, cooked and held before serving, and prepared, cooked and held before serving, respectively.

• Food Science and Preservation
• /
• v.12 no.6
• /
• pp.546-551
• /
• 2005

The new developed production process and the coating equipment were used to prepare the alginate coated rice having functional property. Then, the quality characteristics such as proximate analysis, moisture sorption properties, influence on the retrogradation, sensory evaluation were investigated. The moisture content of the alginate coated rice was $16.5-18\%$ which is $1.5\%$ higher than the normal rice. About $0.3\%$ alginate was coated on the rice by the measurement of carbohydrate content after coating with $2\%$ alginate. The rice coated with higher alginate concentration showed the higher moisture absorption. The rice coated with $2\%$ alginate solution stored $30^{\circ}C$ and $85\%$ RH conditions for 6 weeks and it increased $1.8\%$ of the moisture content The alginate coated rice has delayed the retrogradation more than 6 hrs as well as got the higher scores for the appearance, stickiness, and taste. The alginate coated rice is a good source of the fiber in the nutritional aspect and it improves the quality and functionality of the rice.

• Composites Research
• /
• v.33 no.5
• /
• pp.296-301
• /
• 2020

Laminated composite materials have excellent in-plane properties, but are vulnerable in thickness directions, making it easy to delamination when bending and torsion loads are applied. Thickness directional reinforcement methods of composite materials that delay delamination include Z-pinning, Stitching, Tufting, etc., and typically Z-pinning and Stitching method are commonly used. The Z-pinning is reinforcement method by inserting metal or carbon pin in the thickness direction of prepreg, and the conventional stitching process is a method of reinforcing the mechanical properties in the thickness direction by intersecting the upper and lower fibers on the preform. In this paper, I-fiber stitching method, which complement and improve weakness of Z-pinning and Stitching method, was proposed, and the static strength of composite single-lap joints using I-fiber stitching process were evaluated. The single-lap joints were fabricated by a co-curing method using an autoclave vacuum bag process. The thickness of the composite adherend was fixed, and 5 types of specimens were manufactured with varying the stitching pattern (5×5, 7×7) and angle (0°, 45°). From the test, the failure load of the specimen reinforced by the I-fiber stitching process was increased by up to 143% compared to that of specimen without reinforcement.

• Journal of Energy Engineering
• /
• v.17 no.1
• /
• pp.8-14
• /
• 2008

The effects of calcium type catalysts addition on the thermal decomposition of low density polyethylene (LDPE) and ethylene vinyl acetate (EVA) resin have been studied in a thermal analyze. (TGA, DSC) and a small batch reactor. The calcium type catalysts tested were calcinated dolomite, lime, and calcinated oyster shell. As the results of TGA experiments, pyrolysis starting temperature for LDPE varied in the range of $330{\sim}360^{\circ}C$ according to heating rate, but EVA resin had the 1st pyrolysis temperature range of $300{\sim}400^{\circ}C$ and the 2nd pyrolysis temperature range of $425{\sim}525^{\circ}C$. The calcinated dolomite enhanced the pyrolysis rate in LDPE pyrolysis reaction, while the calcium type catalysts reduced the pyrolysis rate in EVA pyrolysis reaction. In the DSC experiments, addition of calcium type catalysts reduced the melting point, but did not affect to the heat of fusin. Calcinated dolomite reduced 20% of the heat of pyrolysis reaction. In the batch system experiments, the mixing of calcinated dolomite and lime enhanced the yield of fuel oil, but did not affect to the distribution of carbon numbers.

• The Journal of Engineering Geology
• /
• v.26 no.1
• /
• pp.51-61
• /
• 2016

New building methods are needed to aid increased inner-city redevelopment and industrial construction. A particular area of improvement is the efficient use of cut slopes, with the minimization of associated problems. A retaining wall of precast panels can resist the horizontal earth pressure by increasing the shear strength of the ground and reinforcing it through contact with the panels. Precast panels allow quick construction and avoid the problem of concrete deterioration. Other problems to be solved include the digging of borrow pits, the disposal of material cut from the slope, and degradation of the landscape caused by the exposed concrete retaining wall.This study suggest the methods of improvement of an existing precast panel wall system by changing the appearance of the panels to that of natural rock and improving the process of adhering the panel to a vertical slope. The panels were tested in the laboratory and in the field. The laboratory test verified their specific strength and behavior, and the field test assessed the panels' ground adherence at a vertical cutting. Reinforcement of the cutting slope was also measured and compared with the results of 3D numerical analysis. The results of laboratory test, identified that the shear bar increase the punching resistance of panel. And as a results of test construction, identified the construct ability and field applicability of the panel wall system adhered to in-situ ground. In addition to that, extended measurement and numerical analysis, identified the long-term stability of panel wall system adhered to in-situ ground.

• 한국신재생에너지학회:학술대회논문집
• /
• 2005.06a
• /
• pp.507-511
• /
• 2005

울돌목은 조류발전의 세계적인 최적지로 꼽히고 있으며 서해와 남해의 점이 지대로서 조류에 의해 해양 생물 군집의 대량 이동이 빈번한 곳이라 할 수 있다. 조류 발전 시설인 터빈의 가동은 물리적인 충격에 의해 해양 생물의 생태-생리 반응에 영향을 미칠 가능성이 있다. 네트를 이용한 1차 조사에서 터빈 가동에 의한 동물플랑크톤의 순 사망률은 $44.3\%$로 나타났다. 1차 조사 이 후 다이아프램 펌프를 이용한 조사 결과 중 출현 개체수가 높았던 조사에서 전체 동물플랑크톤의 순 사망률은 각각 $7.3\%,\;5.8\%$를 나타내었고, 요각류는 각각 $4.4\%,\;5.2\%$를 나타냈다. 물리적인 충격을 인위적으로 가한 실험에서 스트레스를 받은 요각류 Acartia hongi의 알 생산은 스트레스를 받지 않은 것보다 $1.8\~2.3$배 낮은 경향을 보였다. 본 조사에서 동물플랑크톤이 낮은 사망률을 보골 이유는 작은 크기의 생물이 우점하였기 때문이며 조사 결과에서 몸체가 비교적 단단하고 크기가 작은 요각류는 상대적으로 약한 부유유생보다 높은 생존율을 보였다. 울돌목 조사 해역에서 출현한 동물플랑크톤은 크기가 작아 터빈의 물리적인 충격에 의한 사망률은 낮을 수 있으나 순간적으로 강한 스트레스를 받는다면 재생산을 포함한 생리활동이 저하될 수 있음을 보였다. 네트 및 펌프를 이용한 조사 결과에서 네트에 의한 채집은 터빈의 영향뿐만 아니라 빠른 유속으로 인하여 네트가 받는 압력에 의해 생물체가 손상되는 양상이 높아 사망률이 높았던 것으로 보인다. 그러나 다이아프램 펌프는 생물 채집 시 오류를 최소화하는 장점은 있으나 채집의 장시간에 비해 매우 적은 생물량이 채집되는 단점을 보였다TEX>$96.5\%$에 미달하는 문제는 식물성 원료유로 제조한 고순도 바이오디젤과 혼합 사용하거나 감압 증류 공정을 통해 고농도의 폐식용유 바이오디젤을 제조하여 해결 가능하다. 대전시 신성동 소재의 음식점에서 수거한 폐식용유를 원료로 하여 생산한 바이오디젤의 차량 배출가스 실증 테스트 결과 경유 차량의 주 오염물질인 PM과 Soot 및 기타 오염물질의 배출량은 감소하였으나 NOx의 배출량은 약간 증가하는 것으로 나타났다구와 이해를 바탕으로 보존대책이 마련되어야 한다.되었다. 이런 모든 시편들을 각 탈염방법에 따라 탈염처리한 후 XRD와 SEM-EDS으로 분석한 결과 인철광과 침철광은 어떠한 변화도 보이지 않았고, 다만 적금광으로 동정된 시편만이 잔존하지 않았다. 철기 제작별 $Cl^-$ 이온 추출량과 탈염효과에 대한 비교 실험은 이온 크로마토그래피 분석 결과와 마찬가지로 단조 철제유물이 주조 철제보다 $Cl^-$ 이온을 많이 가지고 있었으며, 탈염 처리 후에는 $Cl^-$ 이온은 전혀 발견되지 않았다. 이상의 결과 $K_2CO_3$와 Sodium 용액은 탈염처리에서 가장 적합한 탈염처리 용액으로 알수가 있었으며 특히 어떠한 탈염 용액으로 유물을 처리한다 해도 철제유물에 생성된 부식물은 제거되지 않는다는 것을 알게 되었다. 따라서 보존처리자는 유물 표면의 부식 상태만을 보고 처리하기 보다는 철기제작물로 고려하여 처리하는 것이 필요하다. 또한 금속에 부식을 야기시키는 $Cl^-$ 이온과 부식물을 완전하게 제거하여 탈염처리를 하는 것이 유물 부식을 최대한 지연시킬 수 있는 것이라 생각된다.TEX>$88\%$)였다.(P=0.063). 결론: 본