• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.43 no.6
• /
• pp.533-539
• /
• 2015

Recently, guided missiles applies folding wings to save space. During wing deployment, aero force acting on wing effects significantly on deployment performance, usually aerodynamic coefficient are calculated by CFD analysis. However, Missile Datcom can calculates estimated aerodynamic coefficient very quickly by assuming wing deployment motions as dihedral angle of wing. If missile has external store, wings may need to be folded on top of each other. In this case, one of wing help or interrupt other wing deployment, locking effect. In this study, both effects were included on wing deployment performance analysis to criteria for wings locked condition and formulated wing deploy performance, and compared with wind tunnel test data. Analysis predicted vulnerable wind direction of wing deployment very well.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.42 no.4
• /
• pp.298-304
• /
• 2014

The lifting-line method based on Weissinger's method is extended to be able to analyze the ground effect. The method is applied to predict the variation of aerodynamic performance due to ground effect for the elliptic wing with aspect ratio of 10 and the wing of human powered aircraft. While the vortex strength of the wing increases slightly, the downwash decreases significantly as the wing approaches to the ground. For the wing of human powered aircraft, the increment of lift at the height of 2m is 5% than the lift outside the influence of ground effect. The decrease of induced drag at the height of wing span is 10% and at the height of 2m is 55% than that out of ground effect.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.12 no.6
• /
• pp.111-118
• /
• 2004

The work presented in this paper concerns the aerodynamic characteristics and compression wave generated in a tunnel when a high speed train enters it. A large number of solutions have been proposed to reduce the amplitude of the pressure gradient in tunnels and some of the most efficient solutions consist of (a) addition ofa blind hood, (b) addition of inclined part at the entrance, and (c) holes in the ceiling of the tunnel. These are numerically studied by using the three-dimensional unsteady compressible Euler equation solver with ALE, CFD code, based on FEM method. Computational results showed that the smaller inclined angle leads to the lower pressure gradient of compression wave front. This study indicated that the most efficient slant angle is in the range from $30^{\circ}$ to $50^{\circ}$. The maximum pressure gradient is reduced by $26.81\%$ for the inclined angle of $30^{\circ}$ as compared to vertical entry. Results also showed that maximum pressure gradient can be reduced by $15.94\%$ in blind hood entry as compared to $30^{\circ}$ inclined tunnel entry. Furthermore, the present analysis showed that inclined slant angle has little effect on aerodynamic drag. Comparison of the pressure gradient between the inclined tunnel hood and the vertical entry with air vent holes indicated that the optimum inclined tunnel hood is much more effective way in reducing pressure gradient and increasing the pressure rise time.

• Aerospace Engineering and Technology
• /
• v.10 no.1
• /
• pp.30-38
• /
• 2011

Structural effects of several geometric parameters such as shroud thickness, edge roundness and fillet radius of turbopump turbine blade were investigated throughout transient finite element analyses. Usually shroud is inserted to increase aerodynamic efficiency, but blocks deformation of blades. Therefore it can increase stress level in a structural point of view. Likewise, edge roundness and fillet between blades are also parameters where aerodynamics and structural mechanics should compromise. In this study, overall stress levels according to the geometric parameters were thoroughly investigated and the results could be utilized to determine optimal geometries.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2010.11a
• /
• pp.519-522
• /
• 2010

Flow-induced vibration analyses have been conducted for a 3D compressor blade model. Advanced computational analysis system based on computational fluid dynamics(CFD) and computational structural dynamics has been developed in order to investigate detailed dynamic responses of designed compressor blades. A fully implicit time marching scheme based on the Newmark direct integration method is used for computing the coupled aeroelastic governing equations of the 3D compressor blade for fluid-structure interaction problems. Detailed dynamic responses and instantaneous pressure contours on the blade surfaces considering flow-separation effects are presented to show the multi-physical phenomenon of the rotating compressor blade.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.50 no.9
• /
• pp.599-608
• /
• 2022

Urban air mobility (UAM) equipped with rotor system is subject to ground effect at vertiport during takeoff and landing. The aerodynamic performance of the aircraft in ground effect should be analyzed for the safe operation. In this study, The ground effects on the aerodynamic performance and wake structure of the quadcopter electric vertical takeoff and landing (eVTOL) configuration equipped with coaxial counter-rotating propellers were investigated by using the lattice Boltzmann method (LBM). The influence of the ground effect was observed differently in the upper and lower propellers of the coaxial counter-rotating propeller system. There was no significant change in the aerodynamic performance of the upper propeller even if the propeller height above the ground was changed, whereas the averaged thrust and torque of the lower propeller increased significantly as propeller height decreased. In addition, the amplitude of the thrust fluctuation tended to increase as the propeller height decreased. The propeller wake was not sufficiently propagated downstream and was diffused along the ground due to the outwash flow developed by the ground effect. The impingement of the rotor wakes on the ground and a fountain vortex structure were observed.

• Aerospace Engineering and Technology
• /
• v.4 no.1
• /
• pp.39-44
• /
• 2005

To validate the rotor performance analysis, 3D Computational Fluid Dynamics(CFD) analysis was performed for tilt rotor aeroacoustic model(TRAM). Also, 3D vehicle with rotating rotors was simulated for rotor power effect analysis. Multiple reference frame(MRF) and sliding mesh techniques were implemented to capture the effect of rotor revolution. CFD results were compared with the wind tunnel test results to validate their accuracy. At helicopter mode, CFD analysis predicted lower thrust than the wind tunnel test but CFD results showed good agreement with the test result at cruise mode. Rotor power effect decreased the lift but did not change drag and pitching moment.

• Journal of the Korean Society for Aviation and Aeronautics
• /
• v.25 no.2
• /
• pp.63-68
• /
• 2017

In the present study, a wind tunnel test for a rotor-blade configuration was conducted to investigate a basic aerodynamic performance and a effect of the cross wind. The diameter of the configuration was 1.46 m and the test was carried out for both a clean and a tripped configurations. The boundary layer for the trip configuration was simulated by zig-zag tape and the test performed on constant-velocity and constant-rotational modes. It was shown that the test result for the tripped configuration reduces the maximum power coefficient by 9.4% ~ 12.1% compared to the clean one. Within $5^{\circ}$ of the flow angle, there is no significant loss of power, however, the coefficient is reduced by 5.3% ~ 36.7% in the range of $10^{\circ}{\sim}30^{\circ}$.

• Proceedings of the KSME Conference
• /
• 2001.06e
• /
• pp.416-421
• /
• 2001

This paper presents the numerical prediction of sound generated by viscous flow past a circular cylinder. The two dimensional flow field is predicted using FEM based Reynolds-averaged Navier-Stokes solver, and the calculated unsteady fluid field values are utilized by an acoustic code that implements Ffowcs Willianms-Hawkings(FW-H) equation. The integration surface used in acoustic analysis is extended from the cylinder surface to permeable surfaces. The 2D based CFD calculations overpredict the acoustic amplitude, however, if adequate correlation length is used, the predicted acoustic amplitude agrees well with experiment. The predictions using extended integral surface in FW-H equation show results that contain the characteristics of quadrupole - volume integration - noise term, and do not vary seriously with the integral surface location.

• The KSFM Journal of Fluid Machinery
• /
• v.2 no.3 s.4
• /
• pp.30-36
• /
• 1999

Blade shape profile in the axial compressor is one of the most important factors governing its aerodynamic characteristics. Manufacturing tolerance, which is inevitable in the blade manufacturing processes, may change blade profile and as a consequence, it will affect the compressor performance. In this paper, influence of manufacturing tolerance on the aerodynamic characteristics of axial compressor blades with distortion of blade profile curvatures is investigated by using a flow simulation technique. It is found that manufacturing tolerance can be an important factor affecting the source of both profile and wake losses of the axial compressor blades.