• Explosives and Blasting
• /
• v.34 no.3
• /
• pp.10-16
• /
• 2016

Recently, transition from open pit to underground mining in limestone mines is an increasing trend in Korea due to environmental issues such as noise, dust and vibrations caused by crushers and equipment. The severe damages in the surrounding rock mass of underground opening caused by explosive blasting may lead to rock fall hazards or casualties. It is well known that variables which mainly affect blast-induced rock falls in underground mining are: blast vibration level, joint orientation and distribution and shape of the cross sections of underground structures. In this study, UDEC program, which is a DEM code, is used to simulate blast vibration-induced rock fall in underground openings. Variation of joint space, joint angle and joint normal stiffness was considered to investigate the effect of joint characteristics on the blast vibration-induced rock fall in underground opening. Finally, jointed rock mass models considering blast-induced damage zone were examined to simulate the critical blast vibration value which may cause rock falls in underground opening.

• Journal of the Korean GEO-environmental Society
• /
• v.16 no.12
• /
• pp.13-22
• /
• 2015

Developed ground cavity due to leakage of decrepit old sewer pipe causes ground surface settlement and brittle fracture of pavement. Recently, for 5 years, frequency of occurrence of ground subsidence phenomenon tends to increase rapidly and/or steadily. It is difficult to investigate ground surface settlement and/or subsidence in urban area because most ground surfaces are covered with asphalt or concrete pavement. In this research, therefore, ground surface settlement, influence zone and settlement of sewer pipe were analyzed using finite element method. Not only reinforced effect of pseudo-plastic backfill that is applied to prevent ground surface settlement or subsidence spot, was compared and analyzed using numerical analysis program, but also direct shear test was carried out to determine strength parameters of pseudo-plastic backfill.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.34 no.6
• /
• pp.1937-1944
• /
• 2014

In recent years, common ducts have been installed and operated in the sidewalls of tunnels to prepare for emergencies in tunnel construction and maintenance. The installation of common ducts is done mainly by humans. Problems with cost increases are inherent in tunnel construction by humans due to the safety risks and the economic inefficiency of humans performing construction activities. Among the problems that arise are poor illumination due to the use of temporarily installed electricity, the risk of accidents due to the confined workspaces, and workers avoiding work tasks because of the poor environment in tunnel. Ideas for solving these problems were developed using a value engineering (VE) process, and mechanized construction was identified as a promising solution. To verify the effectiveness of mechanized construction of a common duct in tunnels, experimental construction work was carried out, and mechanized construction was proven to directly improve the constructability and economic efficiency of common duct construction. In addition, reducing human involvement in common duct construction in tunnels is expected to improve safety, and because of the continuous concrete placement technique used, the finish and appearance of the ductwork are improved.

• Proceedings of the Korean Institute Of Construction Engineering and Management
• /
• 2007.11a
• /
• pp.1039-1042
• /
• 2007

The number of vehicle has been increased due to growth of economy. Consequently, the needs for parking area has been increasing. there is a serious problem in aged-apartments. It result from observing a parking lot law at that times. That is the reason why residents demand parking lot expansion. Parking lot addition is being studied on a lots different standpoint to solve the present parking lot condition. Parking lot expansion is limited by housing complex characteristics. This study analyzed the housing complex characteristics of aged-apartment. It is analyzed that the number of house holders, distance between buildings, and level of site for finding housing complex characteristics. The result are as follows. the complex lower than 300 households is about 35% in the Number of households. The buildings which has a moving distance from 41m to 50 is nearly 23%. Them the 멕스둣 house located on the flat is 82%. This study will become a reference data for the parking lot expansion.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.20 no.2
• /
• pp.287-303
• /
• 2018

In recent years, the occurrence of ground subsidence phenomenon is frequent in Korea. The Korean government has enacted a special law on underground safety and the law will be enforced from January 1, 2018. Under this new law, underground excavation should be assessed for underground safety impacts. After excavation construction, periodic geophysical surveys should be conducted to investigate the occurrence of underground cavities. When underground cavities were discovered, the underground safety was assessed through numerical analysis. However, it is controversial because the method of numerical modeling the discovered underground cavity is due to be established. In this study, the effect of the depth of the underground cavity from the shape of the underground cavity to the underground cavity was studied using a continuum analysis program. In this study, a method to reflect the shape of the underground cavity to the numerical modeling is presented. The relationship between the shape and depth of the underground cavity, and the factor of safety calculated by the shear strength reduction method (SSR) is presented. The results of this study are expected to form the basic data on underground safety impact assessment.

• Journal of the Society of Naval Architects of Korea
• /
• v.41 no.4
• /
• pp.9-16
• /
• 2004

In the cavitation tunnel, the first corner playes role for the flow direction to execute 90-degree turn. So, energy loss is serious, and the cavitation phenomena well occur in the guide vane surface. In this paper, the flow in the first corner was numerically calculated. From the calculation result, cavitation phenomena mainly occurred in the suction side of the last guide vane and vicinity that vane and tunnel wall adjoin each other. And bubbles occurred from all guide vanes if the flow velocity in the test section reaches the any critical value. We could analogize with our experience in the water tunnel that bubbles that occurred in time not vanish, and become miniature in the flow although the pressure recover. So, they circulate with flow in the tunnel, and come into view in the test section. Therefore, first corner must be designed for bubbles not to appear in the test section according to the flow condition like velocity and pressure demanded by the experiment. We analyzed flow in case that the first elbow configuration was redesigned and some of the existing guides vanes were eliminated. And we presented that first elbow can be easely designed for the improvement of tunnel performance through the computational analysis.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.5 no.3
• /
• pp.25-32
• /
• 2001

A passive control method of the interaction between a weak normal shock-wave and a turbulent boundary-layer was simulated using two-dimensional Navier-Stokes computations. The inflow Mach number just upstream of the normal shock wave was 1.33. A porous plate wall having a cavity underneath was used to control the shock-wave/turbulent boundary-layer interaction. The flows through the porous holes and inside the cavity were investigated to get a better understanding of the flow physics involved in this kind of passive control method. The present computations were validated by some recent wind tunnel tests. The results showed that downstream of the rear leg of the $\lambda$-shock wave the main stream inflows into the cavity, but upstream of the rear leg of the $\lambda$-shock wave the flow proceeds from the cavity toward to the main stream. The flow through the porous holes did not choke fur the present shock/boundary layer interaction.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2021.06a
• /
• pp.64-64
• /
• 2021

댐의 중요 구성요소 중 하나인 여수로 구조물은 관행적으로 단위길이당 100m³/s 정도의 유량이 흐를 수 있도록 설계를 하고, 이를 초과할 때는 여수로 구조물에 피해가 가지 않도록 공기혼입 장치를 설치하거나 콘크리트의 설계강도를 증가시키는 대책을 사용하는 것이 일반적이다(댐설계 기준·해설, 2011) 그러나 건설된 지 오래된 댐의 경우 여수로 콘크리트 구조물의 설계강도가 낮고(최저 16.7MPa) 수문방류 횟수가 많아 최근에 건설된 댐 여수로 보다 상대적으로 많은 손상이 발생되어 있어 잦은 보수보강이 요구되고, 점차 유지관리 비용이 증대되고 있어 노후된 여수로 구조물일수록 기능을 유지하면서도 유지관리 비용을 절감할 수 있는 방안의 수립이 요구되고 있다. 이에 본 연구에서는 𐩒𐩒𐩒댐 여수로를 대상으로 2020년 홍수기 전·후의 여수로 바닥슬래브의 손상상태를 3D드론 매핑, 육안조사 및 내구성 조사결과 등을 이용한 정밀분석을 통해 수문방류시 여수로 바닥슬래브에 가장 큰 손상을 일으키는 손상메커니즘으로 유수에 의한 부상(uplift)에 의한 파손 메커니즘(Flow-driven uplift failure mechanism)을 제시하였으며, 여수로 바닥슬래브의 가장 일반적 손상원인으로 간주되고 있는 공동현상(cavitation)이 공동지수(cavitation index)가 0.3이상인 경우에도 발생할 수 있음을 확인하였다. 이와 같은 관찰 및 분석결과는 보다 많은 사례를 통하여 보완될 경우 향후 여수로 구조물의 설계 뿐만 아니라 보수보강 방법이나 유지관리, 더나아가서는 종합적 댐시설물 자산관리 계획을 수립하는데 매우 유용한 자산이 될 수 있다.

• Journal of the Society of Naval Architects of Korea
• /
• v.49 no.2
• /
• pp.151-157
• /
• 2012

The present study explored the possibilities of the applications of open source libraries to shipbuilding and marine engineering industries. A computational fluid dynamics (CFD) code, termed SNUFOAM, was developed and tested for turbulent flow around a ship, free surface flow around a hull, cavitating flow, and vortex shedding dynamics around a cylinder. The results using the developed CFD codes were compared against existing experimental data and solution of commercial CFD codes. SNUFOAM showed the nearly same results as commercial CFD codes and proved to be an alternative to commercial CFD codes for shipbuilding and marine engineering industries.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• v.y2005m4
• /
• pp.364-367
• /
• 2005

A series of computational simulations have been carried out for non-reacting and reacting flows in channel-type and divergent scramjet combustor configurations with and without a cavity. Transverse injection of hydrogen is considered with the injection pressure varying from 0.5 to 1.5 MPa. The detailed resolution of the oscillatory flow and flame dynamics are captured at sufficient scale to identify the underlying physical mechanisms, and the role of combustor configuration, cavity and amount of heat addition could be understood.