• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.23 no.2
• /
• pp.272-280
• /
• 1999

A cycle analysis was achieved to predict the characteristics by comprehensive modeling and simulation of an air-cooled, double-effect absorption system using a new $H_2O/LiBr+HO(CH_2)_3OH$ solution. The simulation results showed that the new working fluid may provide the crystallization limit 8% higher than the conventional $H_2O/LiBr$ solution. With a crystallization margin of 3wt%(weight%), the optimal solution distribution ratio was found in the range of 36 to 40%. Variation of cooling air Inlet temperature has a sensitive effect on the cooling COP and corrosion problem. The simulation of heat exchangers with UA value revealed that the absorber and the evaporator are relatively important for an air-cooled system compared with the condenser and the low temperature generator. The effect of cooling air flow rate, circulation weak solution flow rate and chilled water inlet temperature were also examined. The new working fluid may provide the COP approximately 5% higher than the conventional $H_2O/LiBr$ solution.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2004.05a
• /
• pp.146-146
• /
• 2004

최근 전 세계적으로 사람이 직접 작업할 수 없는 환경이나 작은 공간에서의 용이한 작업수행을 위해서 초소형 정밀 기계 기술에 관한 연구 및 개발이 활발하게 이루어지면서 형상기억합금(Shape Memory Alloy ： SMA)을 이용한 초소형 액츄에이터(Micro Actuator)에 관한 관심이 증대되고 있다. 그 이유 중의 하나는 형상기억합금을 이용한 구동 방식은 다른 구동 방식보다 높은 에너지 대 부피비율을 가지고 있기 때문에 기존의 모터에 의한 구동보다 소형화가 간단하기 때문이다.(중략)

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.7 no.3
• /
• pp.488-500
• /
• 1995

An air-cooled ammonia/water GAX(Generator-Absorber heat eXchange) absorption cooling cycle is proposed and its performance is numerically evaluated. It is shown that the performance of the system is greatly dependent on the quality of the refrigerant leaving the evaporator. For any refrigerant concentration in the investigated range(99.1~99.9% ammonia), the cycle COP(coefficient of performance) reaches the highest value, when some amount(about 7%) of refrigerant evaporates in the refrigerant heat exchanger. Among temperature differences in various heat exchangers, the temperature difference between GAX-absorber and the GAX-generator shows the greatest effect on the system performance, whereas pressure losses cause no significant decrease in COP. The system COP increases almost linearly with increasing evaporator temperature, decreasing absorber temperature or decreasing condenser temperature. If both absorber and condenser temperature increase simultaneously, the decrease in the COP becomes larger.

• Journal of the Korea Society of Computer and Information
• /
• v.20 no.4
• /
• pp.11-16
• /
• 2015

Data center, not only the development of globally of cloud-based IT solutions, As the big data, education, use of development electronic equipment of communication means is increased, Demand of domestic and international data center has increased steadily. Due to the increase of data center demand, heat generation of server rack due to the development of IT equipment is also increasing continuously. Calculating heat value of the data center, because more than 99% of the power usage of IT server is converted into heat, the calorific value as the size and capacity of the server is larger will increase. In this paper, to center the cooling system of air-cooled, and research and development of air conditioning systems for energy reduction of data center, through performance analysis and simulation, it has been analyzed that there is energy savings.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2003.10a
• /
• pp.47-52
• /
• 2003

In the recent years, as the research and the development of micro and precision machinery become active, the interest of micro actuators using SMA(Shape Memory Alloy) has been increased. The dynamic characteristic analysis of SMA is necessary for actuator application and many common researches report the material characteristics of SMA sufficiently. However, the research on dynamic characteristics is very deficient. In this paper, the helical spring are fabricated with NiTi SMA wire of high resistivity. The force, response speed, temperature, and displacement are measured by digital force gauge, infrared thermometer, and laser displacement sensor so that the dynamic characteristics of this SMA is analyzed. Also, bidirectional actuator was fabricated and experimented fir its performance.

• Journal of Korea Foundry Society
• /
• v.17 no.2
• /
• pp.151-157
• /
• 1997

다섯 조성의 서로 다른 Mo, Ni 및 Mn함량을 지닌 3 mass% C-20 mass% Cr 공정조성의 백주철을 질소분위기하에서, 1173, 1273 및 1373 $^{\circ}K$의 온도로 3.6, 7.2, 14.4 및 28.8 ks동안 불안정화열처리를 행한 후 공냉시켜 잔류오스테나이트를 측정한 결과 합금원소함량, 불안정화열처리조건 및 $V{\Upsilon}$사이에 다음과 같은 관계를 얻었다. 즉 Mo, Ni 및 Mn을 첨가한 결과, 주방상태에서 79.89${\sim}$91.65 vol.%범위의 $V{\Upsilon}$가 얻어 졌으며 퍼얼라이트는 전혀 생성되지 않았다. 1173 $^{\circ}K$에서 불안정화열처리를 한 경우에는 무수히 작은 이차탄화물이 석출하였으나 온도가 높아 질수록 그 수는 점차 감소하여 1373 $^{\circ}K$에서는 거의 관찰되지 않았다. 1173 및 1373 $^{\circ}K$에서 불안정화열처리를 한 경우, 불안정화열처리시간의 증가에 따른 $V{\Upsilon}$의 변화는 미미하였으나 1273 $^{\circ}K$의 경우에는 감소하였다. 또한 Mo, Ni 및 Mn의 첨가량이 많아짐에 따라 $V{\Upsilon}$는 증가하였으며 이 두 함수사이의 관계식을 정립시키기 위하여 P인자를 도입하였다.

• Proceedings of the Korea Society for Energy Engineering kosee Conference
• /
• 2003.05a
• /
• pp.351-357
• /
• 2003

In absorption system, the performance of the absorber is critical the overall system performance, size, and first-cost. The objective of this paper is to provide a comprehensive review of the significant effects that researchers have made to numerically analysis model the coupled heat and mass transfer process that occur during falling-film absorption and experimental researches. This study includes experimental work in the enhancement of absorption performance, the effect of the geometry of a vertical absorber, and the effect of configuration of absorption system. This paper is used to highlight key areas which need attention such as film ans vapor hydrodynamics, especially the non-periodicity, instability, and recirculatory motion of waves in the vertical absorber case.

• Korean Journal of Materials Research
• /
• v.6 no.4
• /
• pp.372-378
• /
• 1996

고크롬주철에 있어서 기지 및 탄화물의 조직제어는 내마모성의 향상을 위해 필수적이다. 특히 기지조직내의 잔류오스테나이트함량은 최적 내마모성을 얻기위해 반드시 조절되어야 한다. 본 연구에서는 3% C-18%(or 25%)Cr-Mo-Ni-Mn 고크롬주철을 80$0^{\circ}C$, 90$0^{\circ}C$, 100$0^{\circ}C$ 및 110$0^{\circ}C$의 질소분위기 하에서 각각 20분 불안정화열처리를 행한 후 공냉시켰다. 잔류오스테나이트의 함량은 Xtjs 회절시험을 통해 측정하였으며 회절 peak는 $\alpha$200, $\alpha$220, ${\gamma}$220그리고 ${\gamma}$311을 이용하였다. 화학조성, 불안정화열처리의 온도 및 시간, 그리고 잔류오스테니이트함량강의 관계식을 도출하였다.

• Journal of Energy Engineering
• /
• v.25 no.3
• /
• pp.27-33
• /
• 2016

The heat recovery system that was applied in this study, is the energy-saving type that can produce the maximum cooling capacity less power in use. In order to have a more precise control function the temperature and humidity of the constant temperature and humidity machine, control algorithm is applied to designed a fuzzy PID controller, and the outside air compensation device (air-cooled) demonstrated excellent ability to dehumidify the moisture, $-20^{\circ}C$ in winter. High efficiency and the low-noise type sirocco fan operate quitely and designed to fit the bottom-up and top-down in accordance with the characteristics of equipment. as a result of experiment data, the conversion efficiency is 95% or more, power recovery time is within 5sec, stop delay time is within 30sec, pump down time is 10sec, pump delay time is 5sec, heating delay time is 5sec, temperature deviation is ${\pm}2^{\circ}C$ (cooling deviation: $2^{\circ}C$, Heating deviation : $2^{\circ}C$), humidity deviation is a ${\pm}5%$ (humidification deviation 3.0%, dehumidification deviation 3.0%). Recently, ubiquitous technology is important. so, the constant temperature and humidity machine designed to be able to remotely control to via the mobile phone, and more scalable to support MMI software and automatic interface. Further, the life of the parts and equipment is extended by the failure.

• Solar Energy
• /
• v.12 no.3
• /
• pp.70-83
• /
• 1992

The interaction between the surface radiation and the mixed convection transport from an isolated thermal source, with a uniform surface heat flux input and located in a rectangular enclosure, is stuied numerically. The enclosure simulates a practical system such an air cooled electric device, where an air-stream flows through the openings on the two vertical walls. The heat source represents an electric component located in such an enclosure. The size of this cavity is $0.1[m]{\times}0.1[m]$. The inlet velocity is assumed as 0.07[m/s] and the inlet temperature is maintained as $27^{\circ}C$. The inflow is kept at a fixed position. Laminar, two dimensional flow is assumed, and the problem lies in the mixed convection regime, governed by buoyancy force and surface readiation. The significant variables include the location of the out-flow opening, of the heat source and the wall emissivity. The basic nature of the resulting interaction betwwn the externally induced air stream and the buoyancy-driven flow generated by the source is investigated. As a result, the best location of the heat source to make the active heat transfer is 0.075[m] from the left wall on the floor. The trends observed are also discussed in terms of heat removal from practical systems such as electric circuitry.