• Journal of Korea Water Resources Association
• /
• v.45 no.4
• /
• pp.349-360
• /
• 2012

A horizontally curvilinear non-hydrostatic free surface model that was applicable to three-dimensional viscous flows was developed. The proposed model employed a top-layer equation to close kinematic free-surface boundary condition, and an isotropic k-${\varepsilon}$ model to close turbulence viscosity in the Reynolds averaged Navier-Stokes equation. The model solved the governing equations with a fractional step method, which solved intermediate velocities in the advection-diffusion step, and corrects these provisional velocities by accounting for source terms including pressure gradient and gravity acceleration. Numerical applications were implemented to the wind-driven currents in a two-dimensional closed basin, the flow in a steep-sided trench, and the flow in a strongly-curved channel accounting for secondary current by the centrifugal force. Through the numerical simulations, the model showed its capability that were in good agreement with experimental data with respect to free surface elevation, velocity, and turbulence characteristics.

• Korean Journal of Agricultural Science
• /
• v.30 no.2
• /
• pp.164-174
• /
• 2003

This study was performed to suggest a rational method for the stability evaluation of agricultural reservoir in the very soft ground. The stability methods for agricultural reservoir was used to compare and analyze with various condition by limit equilibrium method. The behavior of settlement-displacement obtained by field monitoring system was used to compare and analyze with various stability methods, and to investigate the applicability of the methods for stability evaluation of agricultural reservoir. The horizontal displacement was abruptly increased when physical properties of soft clay reached its maximum values and therefore, the values of these properties could be used to the fundamental data for stability evaluation. The evaluation of the stability of agricultural reservoir was suggested to use the inclination of curve rather than critical line.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.36 no.5
• /
• pp.377-383
• /
• 2016

The effect of long-term aging degradation on magnetic properties of ferritic 11Cr low-carbon steel was investigated. Coercivity and hysteresis loss measured from the hysteresis loops decreased with long-term aging time and showed that the relation was well fitted by a second order exponential function. Vickers hardness also decreased with aging time and resulted in mechanical softening. In addition, the microstructural evolution was observed by the scanning electron microscopy, backscattered electron image and X-ray diffraction. The $Cr_{23}C_6$ precipitates along grain boundary grew fast and Laves ($Fe_2W$) phase on martensitic lath boundaries in interior grains was developed. The solid solution atoms depleted in matrix and lath subgrains recovered owing to precipitate coarsening with long-term aging degradation. There was a close relation with softening of magnetic and mechanical properties.

• Journal of Korea Water Resources Association
• /
• v.30 no.6
• /
• pp.597-610
• /
• 1997

One-dimensional numerical models using finite difference methods for unsteady sediment transport on alluvial river channel are developed. The Preissmann implicit scheme and the Lax-Wendroff two-step explicit scheme with the Method of Characteristics for water motion and a forward time centered space explicit scheme for sediment motion are developed to simulate the sediment transport rate and the variation of channel bed level. The program correctness of each model is successfully verified using volume conservation tests. The sensitivity studies show that higher peak stage level, steeper channel slope and longer flooding duration produce more channel bed erosion. and median grain size, $D_{50}=0.4mm$ give maximum volume loss in this study. Finally, the numerical models are found to produce reasonable results from the various sensitivity tests which reveal that the numerical models have properly responded to the changes of each model parameter.

• Magazine of the Korea Concrete Institute
• /
• v.8 no.1
• /
• pp.145-153
• /
• 1996

The fracture process zone in concrete is a region ahead of a traction-free crack, in which two major mechanisms, microcracking and bridging, play important roles. The toughness due to bridging is dominant compared to toughness induced by microcracking, so that the bridging is dominani: mechanism governing the fracture process of concrete. Fracture mechanics does work for concrete provided that the fracture process zone is being considered, so that the development of model for the fracture process zone is most important to describe fracture phenomena in concrete. In this paper the bridging zone, which is a part of extended rnacrocrack with stresses transmitted by aggregates in concrete, is modelled by a Dugdale-Barenblatt type model with linear tension-softening curve. Two finite element techniques are shown for the analysis of progressive cracking in concrete based on the discrete crack approach: one with crack element, the other without crack element. The advantage of the technique with crack element is that it dees not need to update the mesh topology to follow the progressive cracking. Numerical results by the techniques are demonstrated.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.12 no.1
• /
• pp.1-8
• /
• 1992

A method analizing contact pressure between plate and elastic half space is presented by using F.E.M. With the method, the pressure intensities at surface nodes of half space cae be directly calculated by using flexibility matrix of half space. The method is originally presented by Y.K. Cheung et al.(3) Insted of Y.K. Cheung's method, which use a conception of equi-contact pressure area around each surface nodes of half space in the noded rectanqular element area. We use the equi-contact pressure area around the Gaussian integration points of half space surface in the noded isoparametric element area. Numarical examples are presented and compared with other's studies.

• Journal of Advanced Marine Engineering and Technology
• /
• v.34 no.5
• /
• pp.678-685
• /
• 2010

GTAW was carried out to the austenitic 304(STS 304) and 22 APU stainless steels. In this case, difference of the corrosion characteristics of welded zone with STS 304 and 22APU mentioned above was investigated with electrochemical methods. Vickers hardness of weld metal in case of STS 304 (Hv-250) showed a relatively higher value than this of 22 APU(Hv-217). The corrosion current densities of weld metal of 22APU and heat affected zone of STS 304 were observed at the highest value compared to those of other welding zone respectively. This is probably because chromium depletion field due to chromium carbide formed to weld metal of 22APU and to heat affected zone of STS 304 can preferentially easily be corroded with more active anode than other fields. Consequently it is thought that application of the other welding methods like as laser welding or using of the optimum filler metals is necessary to improve the corrosion resistance of welding parts of these steels.

• Journal of KIISE:Computer Systems and Theory
• /
• v.35 no.8
• /
• pp.407-415
• /
• 2008

This paper presents novel segmentation and transition techniques for dancing motion synthesis. The segmentation method for dancing motions is based on Laban Movement Analysis (LMA). We assume a dance sequence as a set of small dancing motions. To segment a dancing motion is a subjective, psychological, and complex problem, so we extract the shape factor of LMA from a dance motion and observe shape's changes to find the boundaries of dance segments. We also introduce a transition method that meets constraints on the feet. This method that is based on a linear interpolation modifies the intermediate posture motion after analyzing footprint positions. The posture could be a key-frame between source motion and target motion on the transition. With the proposed techniques, it would be easy for multimedia applications to generate plausible dance motions.

• Journal of Yeungnam Medical Science
• /
• v.13 no.1
• /
• pp.134-140
• /
• 1996

Recently many studies have shown the usefulness of computed tomogram in diagnosing abdominal mass when clinical and conventional radiologic examinations fail to reveal the nature of abdominal mass or the cause of abdominal distension. To evaluate the usefulness of CT in diagnosing neuroblastoma, we retrospectively analyzed computed tomographic findings of 16 neuroblastoma patients, who pathologically proved in Yeungnam University Hospital from 1986 to 1995. The age range of the patients studied were from 8months to 18years. The most frequent sith of origin was adrenal gland and the next was retroperitioneum. The presenting symptoms were palpable mass, abdominal distension, and abdominal pain. The viewpoints of this analysis were turnoral calcifications, midline cross, shape, margin, internal structure, contrast enhancement patterns, major vessel involvement, and lymph node involvement. Characteristic CT findings were as follows: Fine dense curvillinear calcification within the tumor(56%), midline cross(50%), lobulation(75%), well-circumscribed margin(56%), cystic degeneration(56%), heterogeneous contrast enhancement(69%). encasement of major vessels such as aorta, IVC and celiac trunk(50%), and paraaortic lymphadenopathy(87%). We conclude that these CT findings were very common and could be helpful in diagnosting and differentiation neuroblastoma in infant and children.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.11
• /
• pp.363-367
• /
• 2016

A test section of a supersonic wind tunnel was designed for the analysis of flow characteristics over a backward-facing step with Mach 1.0 slot injection in a supersonic flow of Mach 2.5. The cavity flow of a high-speed vehicle is very complex at supersonic speed, so it is necessary to do experiments using supersonic wind tunnels to verify numerical analysis methods. The previous 2D symmetrical nozzle was replaced with an asymmetrical nozzle. The inviscid nozzle contour was designed using Method of Characteristics (MOC), and the boundary layer thickness correction was reflected by experimental data from the wind tunnel. The results were compared with a CFD analysis. The PID control system was changed to be based on the change of tank pressure. This improved the control efficiency, and the run times of supersonic flow increased by about 1 second. The flow characteristics over a backward facing step with slot injection were visualized by a Schlieren device. This equipment will be used for an experimental study of the film cooling effectiveness over a cavity with various velocities, mass flows, and temperatures.