• Journal of Korean Society of Steel Construction
• /
• v.23 no.3
• /
• pp.261-273
• /
• 2011

Recently, the demands for steel frame are increasing because of the trend and due to the demand for bigger and higher buildings. In the analysis of typical steel frame, connections are based on the idealized fixed or pinned connection. A fixed connection assumes that the relative angle of each member before deformation is the same after the transformation. Therefore, the stiffener reinforces the connection to sufficient rigidity and stability of the panel zone. In the economical aspect, however, the necessity of connection that the stiffener reinforcement has omitted is increasing due to the excessive production as well as labor costs of connection. In contrast, pinned connection is assumed that bending moments between the beams and columns do not transfer to each member. This is easy to make in the plant and the construction is simple. However, the structural efficiency is reduced in pinned connection because connection cannot transfer moments. The introduction of this semirigid process can decide efficient cross-sectional dimensions that promote ease in the course of structural erection, as performed by members in the field-a call for safety in the entire frame. Therefore, foreign countries exert efforts to study the practical behavior and the results are applied to criterion. This paper analyzes the semirigid connection of domestic steel by design specifications of AISC/LRFD and make data bank that pertain to each steel. After wards, the results are compared to those of idealized connection; at the same time, this paper presents a design method that matches economic efficiency, end-fixity, and rotational stiffness.

• Korean Journal of Construction Engineering and Management
• /
• v.7 no.2 s.30
• /
• pp.71-80
• /
• 2006

It is required to study systematical on the concrete quality management to extend structure life because rebuilding effect is reducing under present condition of large sized and high stories structure. Concrete, which shows its intensity by hydrating action and a big change in quality according to hot weather and temperature, produces a lot of quality problem under hot and cold weather. Because of each specification and construction plan which does not have basic standard on site, concrete's quality is irregular and makes some defect. As a result, Dae-gu is fumed out to be the longest area after investigating application period and days focused on 8 cities weather information about t relationship between hot weather circumstance and construction environment. Therefore, we first surveyed the curing construction processing in the region and found out the problem of quality management. Then figure out the way of solution. Moreover, we integrated curing quality management, which is applied differently to each site, to have equal quality and to reduce defect from construction site. And then, based on various test of construction condition and analysis of quality management item, we suggest effective concrete quality management to make curing construction standard guide and plan under hot weather.

• Korean Journal of Construction Engineering and Management
• /
• v.13 no.2
• /
• pp.120-127
• /
• 2012

Today, most construction projects have been higher, bigger, and more complicated gradually. So the domestic construction companies have been trying to understand overall construction process and relationships between activities, and adopted various management techniques and tools in order to perform a systematic and effective scheduling. However numerous problems have been occurred on the practical applications because most existing scheduling softwares adapt ADM and PDM techniques. One of them, PDM, is so uneffective because it represents the overlapping relationships between two consecutive activities only by the combinations of start and finish points between two activities. In order to supplement the demerit of PDM, Beeline Diagramming Method(BDM) is proposed as a new networking technique, it can represent two-way multiple overlapping relationships between two activities directly. However there are occurring a loop phenomenon on applying two-way multiple overlapping relationships. This research proposes and verifies the schedule computation method of two-way multiple overlapping relationships on the BDM network.

• Journal of the Korean Institute of Educational Facilities
• /
• v.4 no.1
• /
• pp.53-64
• /
• 1997

지난 20여년간의 비약적 경제 성장을 통하여 우리 사회는 모든 물리적 측면에서 양적인 성장과 질적인 발전을 거듭하여 왔다. 이러한 경제 성장기를 거치면서 우리의 삶은 다각도에서 변화를 겪었으며 건축환경에도 많은 변화가 있었다. 정보화, 세계화라는 시대적 흐름은 우리의 생활자체를 급속도로 변화시키고 있으며 업무용 시설을 포함한 모든 건축물이 대형화, 고층화 뿐 아니라 정보화, 현대화되고 있다. 그러나, 교육의 중요성과 이를 뒷받침해 줄 학교 시설의 중요성에도 불구하고 교육환경의 질적 개선은 상대적으로 낙후되어 있는 상황이라고 할 수 있다. 교육개혁위원회의 교육개혁방안이 계속적으로 나오고 있고 서울의 불암초등학교를 필두로 한 시설 현대화 시범학교가 시도별로 마련되고는 있지만 전반적인 교육 환경은 아직 열악한 상태이다. 특히 구도심부에 위치한 초등학교의 경우, 준공된 후 30년 이상 경과된 학교 건물을 사용하고 있는 경우가 적지 않아 안전상의 문제마저 안고 있는 실정이다. 따라서, 건물의 내구 연한이 그 한계에 달해 가고 유지보수비용이 계속적으로 늘어 경제성을 잃어 가고 있는 학교들을 대상으로 한 재건축과제가 신설 학교의 신축 또는 기존학교의 이전 못지 않은 주요 과제로 대두되고 있다. 더욱이 기존 학교의 재건축사업은 수업을 진행시켜가며 철거 및 신축공사가 단계적으로 수행돼야 한다는 어려움을 갖고 있다. 본 연구는 초등학교의 재건축을 위한 기본적인 자료를 정리하고 배치 및 평면 계획을 중심으로 한 계획 대안을 작성, 검토하여 대안별 장단점을 분석한 후 가장 바람직하다고 평가되는 안을 제시하는 것을 연구의 범위로 하였다. 계획안의 작성에 앞서 실시된 문헌조사 및 실측조사를 통하여, 신축되는 홍파초등학교에 필요한 시설의 내용 및 규모가 산정되었는데 특기할 사항은 좁은 대지임에도 불구하고 가능한 체육관 시설을 포함시키고자 하였다는 것이다. 홍파초등학교 부지는 $8,960m^2$ 정도밖에 안되는 좁은 부지로서 운동장도 제대로 확보할 수 없는 상황이었으나 체육관의 높은 활용도 및 장래의 필요성을 고려하여 소규모라도 계획되는 것이 바람직하다고 판단하였다. 열린교육에의 대응, 제반 특별교실의 확충, 식당 및 지하주차장의 확보 등 모든 시설이 현재 및 장차의 사용에 적합하도록 계획하여 현 시설의 1.5배 정도의 연면적을 갖는 신축 계획안을 작성하였다. 서울대학교와 광운대학교에서 분담하여 실시된 계획안의 작성을 통하여 총 4개의 계획안이 도출되었으며 이 대안들을 채광 및 환기, 학년별 zoning, 기능별 zoning, 열린교실의 정도, 지역사회에의 개방성, 재건축 공사의 용이성, 규모, 옥외공간의 활용성, 동선 계획, 조형성 등 10개 항목을 기준으로 평가하였다. 이러한 비교분석을 통하여 결론적으로 제1안을 최적안으로 제시하게 되었으며, 이를 바탕으로 구체적인 최종 설계안이 도출되기를 기대하는 바이다.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2010.05a
• /
• pp.39-40
• /
• 2010

The demands for longer span and reduction of story height have greatly increased as building structures become much larger and higher in recent years. Although the development of flexural members for reducing story height or making long span has been studied by many researchers and engineers, there is still a lack of efficient systems that meet these two demands simultaneously. This study aimed at developing a new composite beam system suitable for long span and reduction of story height, and proposed a prestressed composite beam with corrugated web. It has great resistance against non-symmetric construction load due to its strong out-of-plane shear strength with relatively small member height as well as good constructability and economic efficiency by removing/minimizing form work. The corrugated webs also make accordion effect introducing larger effective prestressing force to top and bottom flanges, which causes larger upward camber reducing the member deflection. Five full-scale specimens with key test parameters, which are web sectional shapes and number of drape points, were tested to understand their flexural behavior and to verify the performance of the proposed method. The experimental test results showed that the proposed prestressed composite beam had greater flexural strength and stiffness than the ordinary non-prestressed composite beam.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.22 no.1
• /
• pp.1-5
• /
• 2018

The present study investigated the characteristics of vertical sagging down of high temperature in chamber and characteristics of vertical sagging down in the outdoor asphalt sheet and asphalt seal under korea ltimate condition using asphalt seal products of solvent based type, solventless type, water dispersion type, and heat melting type, which are currently applied in Korea. Prior to the investigation of outdoor vertical sagging down characteristics, the assessment of sagging down performance of single use of sealing products at $20^{\circ}C$, $40^{\circ}C$, $60^{\circ}C$ was conducted and the result showed that sagging down did not occur at $20^{\circ}C$ but some solventless type, water dispersion type specimens at $40^{\circ}C$ had sagging down up to 10 mm. In addition, some solventless type, water dispersion type specimens had sagging down up to 55 mm at $60^{\circ}C$. For specimens to which asphalt seal and renovated asphalt sheet were layered over the outdoor concrete vertical surface, sheet sagging and sagging down occurred up to 50 mm in water dispersion specimens after three month later since the construction in summer.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.17 no.2
• /
• pp.110-116
• /
• 2013

A concrete structure has become bigger and higher because of development of construction technology and a change in construction environment. Also it tends to focus on repairing, reinforcement and exterior in harmony with environment for structure maintenance and performance improvement. The research is about eco friendly durable painting applicable to concrete structure using civil and architecture. it purpose to improve external beauties and durable problems due to flexibility by variation of temperature, adhesion of exterior wall, crack and delamination in existing organic and mineral painting. For those problems, we made a eco friendly pre-paint that is made with preliminary treatment mixture as a highly enriched waterproof agent and adhesive increasing agent in preprocessing mixture. Then we performed an experiment on durability of prevention neutralization of concrete, durability abrasion, hiding power, adhesion, temperature resistance and resistance to chemical attack. The result of an experiment shows that hiding power is over 0.96 in standard test, durability abrasion test got higher value 1mg than water paint 75mg and tensile strength is 6 times higher than standard waterproof specification.

• Korean Journal of Construction Engineering and Management
• /
• v.21 no.3
• /
• pp.28-38
• /
• 2020

The large-scaled and high-rise construction structures in recent years have increased high place work, leading to an increase in falling accidents (hereinafter, "accidents"). The need for prediction and management of unsafe acts of workers at construction sites has been raised as unsafe acts of workers are identified as the main cause of industrial accidents. This research aims at deriving the improvement effect of unsafe acts by presenting the relationship between unsafe acts of workers and accidents at construction sites as a probability. Unsafe acts of workers were derived based on the analysis of accident cases. In addition, surveys were conducted to calculate the probability of occurrence of accidents caused by unsafe acts (hereinafter, 'accident probability'). The Event Tree Analysis (ETA) was utilized to confirm the final probability according to the combination of unsafe acts and improvement effect. The accident probability by unsafe act was found to be the highest for working after drinking (95.41%) and to be the lowest for equipment and machine utilization (65.70%). The accident probability according to a combination of unsafe acts was the highest when all of the unsafe acts were conducted (13.23%) and was the lowest when none of the unsafe acts were conducted (0.00%).

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.20 no.4
• /
• pp.657-669
• /
• 2018

In recent years, the development of complex urban areas has become saturated and much attention has been focused on the development of underground space, and deep excavation is frequently performed in order to increase the utilization of underground space due to the enlargement of buildings and the high rise of buildings. Therefore, in this study, we tried to understand the behavior of the braced wall and the behavior of the tunnel adjacent to the wall according to the stiffness of the wall and the distance between the tunnel and wall. As a result of the study, the deformation of the braced wall tended to decrease with increasing the stiffness of the wall, and the axial force acting on the struts was also different according to the stiffness of braced wall. When the stiffness of the braced wall is small (2 mm), the point at which the axial force of the braces maximizes is near 0.3H of the wall. When the stiffness of the braced wall is large (5 mm), the axial force is maximum at around 0.7H of the wall. Also, the tunnel convergence occurred more clearly when the separation distance from the braced wall was closer, the stiffness of the wall was smaller, and the tunnel convergence was concentrated to the lower right part. The ground settlement due to the excavation of the ground tended to decrease as the distance between tunnel and braced wall was closer to that of the tunnel, which is considered to be influenced by the stiffness of the tunnel.

• Journal of the Korea Institute of Building Construction
• /
• v.18 no.1
• /
• pp.33-40
• /
• 2018

Currently, in South Korea, because of reducing the construction period or treating wasted water, there are some cases of missing wet curing for concrete structure even though for high strength concrete. This air curing conditions is considered to cause increased possibility of compressive strength decrease, and increasing drying or autogenous shrinkages. As a solution of shrinkage of concrete, The authors' research team conducted the research on improving durability of concrete with decreasing autogenous shrinkage by adding the oil or fat to induce the saponification. Therefore, in this research, the influence of curing method on compressive strength, shrinkage on evaporation rate of high strength mortar including high volume supplementary cementitious materials (SCMs) was evaluated depending on various curing methods such as air curing, drying after painting emulsified refined cooking oil (ERCO), and drying after 7 and 28 days' wet curing. The experimental result showed the air curing method caused approximately 50% of decreased compressive strength and 1.9 times of increased shrinkage rather than the 28-day-wet curing method, thus it was known that the wet curing significantly influences on performance of high strength mortar using high volume SCMs. However, the ERCO painting curing caused decreased performance of concrete rather than drying after 7 days curing while it caused improved performance of concrete than entire period air curing.