• Journal of Advanced Marine Engineering and Technology
• /
• v.40 no.3
• /
• pp.223-227
• /
• 2016

Power supplies make the load compatible with its power source. DC power supplies are extensively used with most electrical and electronic appliances such as computers, television, and audio sets. The presence of non-linear loads results in a low power factor and higher harmonics in the power system. Several techniques for power-factor correction and harmonic reduction have been reported in the literature. This paper proposes a bridgeless boost converter that improves the power factor and reduces the harmonic content in input line currents as compared to full-bridge rectifiers. This bridgeless boost converter eliminates the need of a line-voltage bridge rectifier in conventional boost converter and thereby reduces conduction losses. The effectiveness of the proposed scheme is verified by computer simulations by using the PSIM software.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.18 no.1
• /
• pp.35-46
• /
• 2008

Harmonic vibration characteristics for the general rotor model having a breathing crack are analyzed. Analyses are performed at the half critical speed ranges. The vibration characteristics are explained by using the additional slope and bending moment at the crack position and the influence coefficient showing the structural dynamic characteristics of the rotor. With the low crack depth the magnitude of the additional slope is kept constant even at the speed range at which the orbit magnitude is very sensitive to the rotational speed change. At this speed range the vibration is affected by the influence coefficient only. As the dynamic bending moment exceeds the static bending moment with the increase of crack depth. the additional slope affects the vibration amplitude of cracked rotor and the crack propagation rate increases.

• Journal of KSNVE
• /
• v.8 no.5
• /
• pp.879-886
• /
• 1998

An automated calibration system of sound level meters was developed and tested. As a standard sound source, the speaker unit(Forstex FE208) cabineted by 440$\times$390$\times$490 $\textrm{mm}^3$(LHW) volume wood box was adopted. Including this source, the driving part was found out to have a good linearity of sound pressure output vs AC voltage input. The Hybrid-Bisect/Newton-Raphson method modified by the linearity was adopted as a searching algorithm. Uisng GPIB interface, the console PC make the control, measurements, and calculations and finally make the accumulation of useful data and results automatically by the instructon in the program coded by C languate. Several trials of automatic calibration using this developed system give the reliable results.

• Journal of KSNVE
• /
• v.8 no.5
• /
• pp.887-899
• /
• 1998

It has been resulted that Lagrange multiplier method with statistical approach was superior to traditional harmonic balance method in identifying the nonlinear loudspeaker parameters when output signals were contaminated with Gaussian random noise. We have known that the displacement-dependent characteristic values of nonlinear parameters identified by traditional harmonic balance method were estimated less than original values by the increase of output noise and the stiffness coefficients were very sensitive to output noise. Also, by the sensitivity analysis we have verified that the harmonic distortions in acoustic radiation was mainly due to nonlinearity of force factor caused by uneven magnetic fields and that reducing the nonlinearity of damping coefficients were very effective for improving second harmonic distrotion of acoustic radiation.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.16 no.4
• /
• pp.22-29
• /
• 2002

Usually, much harmonics are included and cause harmonic loss of motor, torque pulsation, electro-magnetic noise and shock etc. by switching function of inverter when drive induction motor variableness inside. It applied partial resonant Buck converter and three phase voltage type SPWM inverter circuit to induction motor driving system in this paper that see to solve such problem. Changed operation condition variously to do input current of circuit that propose sine-wave by unit power factor almost and capacitor supplied bringing back to life voltage by power supply arranging properly assistance diode and electric power switching. Power factor and efficiency improved as that minimize variation of input at power supply voltage polarity reverse by that add voltage reversal function. Also, by using output filter, reduced harmonic of output line to line voltage components, and introduce state space analysis and forecast operation of rectifier. Such all items confirmed validity through simulation and an experiment.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.7 no.2
• /
• pp.194-204
• /
• 2002

In this paper, a new two-phase space vector RPWM(Random PWM) is proposed. In the proposed RPWM, each of two-phase PWM pulses is located randomly in each switching interval. Based on the space vector modulation technique, the duty ratio of the pulses is calculated. Along with the randomization of the PWM pulses, we can obtain the effects of spread spectra of inverter output voltage, d.c link current and audible switching acoustic noise as in the case of randomly changed switching frequency. To verily the validity of the proposed two-phase RPWM scheme, the experiment based on the Cl67 micro-controller was executed. The performance of the proposed scheme was compared with traditional PWM schemes experimentally.

• Proceedings of the KIPE Conference
• /
• 2015.07a
• /
• pp.497-498
• /
• 2015

Random PWM 방식은 기본파의 배수 고조파에 밀집된 성분을 광대역화할 수 있기 때문에 특정 주파수의 노이즈 감소 및 소음 저감 등에 효과가 있는 인버터 스위칭 방식이다. Random PWM을 구현하는 방법은 랜덤 변수를 생성하고 이를 이용하여 스위칭 주파수를 가변하거나, 인가되는 벡터의 위치를 변화시키는 등의 다양한 방법이 있다. 본 연구에서는 Random PWM 구현 방식, 랜덤 변수의 변동 주기, 랜덤 변수가 적용되는 크기 등의 차이에 따라 주파수 광대역화에 미치는 효과를 분석하였다. 이 결과로부터 구현을 위해 요구되는 조건에 따른 Random PWM의 효과를 비교할 수 있으며, 투입 비용 및 시스템 제한 조건 대비 최적의 Random PWM 방식을 선정할 수 있는 기준으로 활용될 수 있다.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2005.05a
• /
• pp.935-940
• /
• 2005

In this paper, dual rotor disk configuration with a coreless stator is proposed for the Lorentz force type integrated motor bearing system. An experimental compensation for the effects of high order harmonics is performed using the digital controller of the experimental setup. The runout profile and rotor unbalance are also identified by the extended influence coefficient method. The experimental results confirm that this compensation method effectively attenuates the rotor vibration all over the operating range of rotational speed.

• Proceedings of the KIEE Conference
• /
• 2015.07a
• /
• pp.1062-1063
• /
• 2015

오프 그리드 형태의 소형풍력발전기는 도심지 또는 사람이 거주하는 지역에 설치되므로 소음, 진동, 안전성 등에 많은 문제가 야기되고 있다. 풍력발전기 내부적으로 소음 및 진동에 가장 큰 영향을 미치는 요소는 코깅토크로 발전기 회전자가 회전할 때 고정자 슬롯과 회전자 영구자석 사이 공극 릴럭턴스 변화에 의해 발생한다. 또한, 코깅토크는 풍력발전기의 초기 기동 풍속에 영향을 미치며, 토크리플 증가의 원인이 되어 코깅토크 저감 설계는 소형풍력발전기 설계에서 필수적으로 이루어져야 한다. 본 논문에서는 실험계획법을 진행하여 이중고정자 발전기의 영구자석 형상 최적화 설계를 통해 코깅토크를 저감 설계를 실시하였으며, 추가적으로 발전기 출력 전압 고조파 발생을 저감시켰다.

• Proceedings of the KIEE Conference
• /
• 2006.07b
• /
• pp.803-804
• /
• 2006

우리는 이전 논문을 통해 Air blower용 모터에서 널리 사용되고 있는 단상 유도기를 기존의 분포 권선 방식에서 벗어나 집중 권선 방식을 사용하여 설계한 결과 생산 공정의 단계를 줄이고 많은 생산 비용을 줄일 수 있었다. 또한 집중 권선형에서 발생할 수 있는 고조파 문제를 로터의 skew와 overlap 권선 방식을 이용하여 해결 할 수 있음을 증명하였다. 그러나 이러한 이점에도 불구하고 시제품의 특성을 측정한 결과 집중 권선형 모터의 자계 불균형 때문에 기존 분포권 모터에 비해 소음과 진동 특성이 좋지 않은 결과를 보였다. 이에 본 논문에서는 소음과 진동 특성을 고려하여 기존의 기동 및 정격 토크 특성을 유지하면서 토크 리플을 저감할 수 있는 방법을 로터의 Skew 각도 영향, 권선 사양 및 스테이터 및 로터 형상 등을 고려하여 새롭게 설계하였고 그 결과를 제시하였다.