• Journal of Korean Society of Steel Construction
• /
• v.29 no.2
• /
• pp.181-192
• /
• 2017

A beam splice method using inclined end-plates and high-strength tension bolts was developed. The end-plates welded to a bracket and a spliced beam are connected each other by using the tension bolts. In the present study, six exterior beam-to-column moment connections were tested under cyclic loading. Test parameters were the end-plate details and bolt arrangements. All specimens were designed so that moment resistances of the end-plates and bolts were greater than the required moment at the beam splice, in accordance with the design methods of AISC Design Guide 4. Test results showed that in the beam splices with the extended end-plates, the beam moment successfully transferred to the bracket, without any defeats such as excessive prying action of the end plates and brittle failure at the end plate-to-beam flange weld joints. However, the deformation capacities of the overall beam-to-column connections were limited due to the brittle failure of the beam-to-column flange weld joints. From the test results, recommendations for seismic design and detailing of the beam-to-column moment connection with inclined end-plate beam splice were given.

• Journal of the Korean GEO-environmental Society
• /
• v.8 no.1
• /
• pp.49-55
• /
• 2007

In order to utilize treads of waste tire as reinforcement material it is necessary to know the interface friction angle between tread surfaces and soil and tensile strength of connection joint of tire treads. In this research large direct shear tests were performed to get the interface friction angle between the inner and outer surfaces of treads and soil for different degree of compaction. From the large direct shear tests, the ratio of interface friction angle to the shear friction angle of sand, ${\delta}/{\phi}$, were 1.06 in outside surface of tire tread and 0.93 in inside surface of tire tread. For weathered granite soil the ratio of interface friction angle was 0.98 and 0.92 for outside and inside of tread, respectively. Also tensile tests were performed using universal testing machine for the connection joint of treads and Tirecell units using bolts. The tensile strength of connection joint increased with the number of bolts and with the sizes of washers. Connection by polypropylene ropes showed lower strength than those of bolts.

• Journal of Korean Society of Steel Construction
• /
• v.15 no.1
• /
• pp.9-15
• /
• 2003

As building structures become higher and longer-spanned these days, welding fabrication may become more and more difficult as the thickness of the plate increases. The use of high-strength steel is one of the solutions to reduce membrane thickness. Using high-strength steel would reduce the size of the column, which is under high axial load. Performance tests of high-strength box-type and H-shaped welded columns subjected to the combined bending and axial compressive load were carried out with variable axial load and slenderness ratio. Beam-column test results showed that the ultimate strength satisfied both ASD and LRFD codes

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.33 no.4
• /
• pp.263-270
• /
• 2020

This study evaluates the structural behavior of connected long-span beams applied for excavation in urban areas with a narrow street. Generally, the reliability of the connection is reduced owing to the defect of the upper flange in the connection. An improved connection part was developed to complement the defects in the connected long-span beam. A finite element analysis based on a commercial program, ABAQUS, was employed to evaluate the behavior of the improved connection part. A numerical analysis model was proposed to analyze the high-strength bolt connection and the composite behavior of steel and concrete applied to the improved connection. The suitability of the proposed numerical analysis was verified by comparing the experimental and numerical analysis results of the references. Using the proposed numerical analysis method, the improved and general connections were analyzed and compared with each other. The stress distribution and elastic-plastic behavior of the long-span beam were analyzed numerically. The analysis confirmed that 25% of the compressive stress was improved, resulting in the improvement of structural safety and performance.

• Journal of Korean Society of Steel Construction
• /
• v.22 no.2
• /
• pp.121-128
• /
• 2010

The current trends in steel construction involve the use of tapered sections to minimize the use of excess materials to the extent possible, by choosing cross-sections that are as economical as possible abandoning the classical approach of using prismatic members. In addition, snug-tightened connections, especially the end-plate type, have the advantage of fetching less construction costs and shorter assembly times as opposed to fully tightened joints. Although they have many merits, however, snug-tightened bolted end plates are extremely complex in their structural behavior. In this study, an experimental investigation of the snug-tightened flush end-plate connections of tapered beams were conducted. The primary test parameters were the torque for the clamping bolt, the loading pattern, the bolt type and the connection failure type. Using initial stiffness and load-carrying capacity as proposed by Silva et al. and AISC (2003), the moment-rotation curve of a linearly tapered member with a snug-tightened flush end-plate connection was predicted. Moreover, numerical and experimental data for moment-rotation curves were compared.

• Journal of Welding and Joining
• /
• v.17 no.1
• /
• pp.133-144
• /
• 1999

To fine seam annealer capacity of through thickness seam annealing in terms of through thickness microstructure change with increased toughness and elongation leaving heat trace on it, high strength steel pipes of ERW with different thickness were tested in different seam annealing temperature measured on the outer surface of pipes. Annealing temperature and microstructure of the weld seam were changed through applied seam annealing condition. Toughness and tensile test with hardness and microstructure analysis were done on the annealed weld seam to fine its characteristics as a primary step and annealing characteristics according to different seam annealing condition. Through a study of annealed ERW weld seam characteristics and seam annealing technology, amount of electric power should apply in decreased manner to arranged inductors of annealer in the order of 1st, 2nd, 3rd, so on for proper seam annealing. For example of 15.4mm thick and 610mm outside diameter pipe, applied power for proper seam annealing is 600 -650kw at 1st inductor, 450 - 500kw at 2nd inductor, 200-250 kw at 3rd inductor of annealer during 10 - 12M/minute moving speed of pipe. Also, the penetration depth of heat trace along the thickness direction of weld during seam annealing can be estimated through the equation 17mm/kv$\times$voltage(kv) with the microstructure and hardness analysis of thick weld seam as well as study of seam annealing and comparison of cooling condition to CCT diagram of low carbon high strength steel. From this result, the difference between the technological applicability of full annealing condition based on phase diagram and full penetration of heat trace based on CCT diagram along the thickness of weld seam is discussed.

• Journal of Welding and Joining
• /
• v.4 no.3
• /
• pp.13-25
• /
• 1986

철강 구조물의 용접기술에 있어 용접부의 신속성을 좌우하는 가장 중요한 요소는 용접균열에 관한 문제와 용접본드부의 취화에 관한 문제로 요약될 수 있다. 일반적으로 용접부 및 그 근방의 금속은 국부적으로 매우 높은 온도까지 급열된 후 급냉되므로, 용접부에서 각종균열의 발성 위험성이 높아지고 용접본드부를 취화하여 파양인성의 저하를 초래하게 된다. 따라서 이러한 문 제점을 극복하기 위해서는 재료의 선택이나 설계, 시공, 검사의 각 단계에서 충분한 검토가 필 요하다. 특히 최근 들어 이전보다 높은 강도의 고장력강재가 널리 사용되고 구조물의 대형화에 따라 구속조건이 증대되며 구조물의 사용 조건은 더욱 가혹 화함에 따라 상술한 문제점은 더욱 중요시되고 있다. 철강 용접부에 발생하는 균열은 용접시공시 발생되는 균열과 용접완료후 구 조물 사용중에 발생되는 균열로 대별될 수 있다. 용접시공중 발생되는 균열은 용접열싸이클로 인해 생성되는 조직, 석출물등의 치금학적 요인과 잔유응력 또는 구속응력등의 역학적 요인이 중첩됨으로서 발생된다. 또한 사용중 발생되는 균열은 상기의 두 가지 요인이외에 환경적 요인이 첨가되어 발생된다고 볼 수 있다. 이상과 같은 용접균열을 방지하기 위해서는 실 구조물 용접 조립시의 각종 조건을 재현한 시험법을 통해 용접균열 발생의 한계조건을 정량적으로 분석할 필요가 있다. 이러한 균열 시험의 결과, 적정한 용접 시공 조건이 도출될 수 있기 때문이다. 이와 같은 필요성에 의해 지금까지 다수의 용접균열 시험법에 관한 연구가 행하여져 왔고 그 중에는 각 국가의 협회나 학회의 규격으로 확립된 것도 많으며 국제규격으로 되어 있는 것도 있다. 본 고에서는 각종균열들에 대한 지금까지 밝혀진 기구들에 대해 해설하고, 그 각각에 적용되고 있는 시험법들에 대해 소개하고저 한다.C1지구의 공업.생활용수는 103units, 33units로 배분되고, 하류지구에 304units로 배분되었다. 따라서 용도별로 물배분하므로서 금호강 하루지역에 더욱 많은 물을 배분할 수 있음을 알았다.통해서 수위-유량관계(rating curve)를 규명하였다. 시험지구의 관개효율 및 용수손실 규명 등에 관한 기본자료를 수집하기 위해서는 계측시스템의 운영은 장기간으로 지속 되어야 한다며, 전기전도도와 토양수 농도, 전기전도도와 함수량의 관계를 이용한 천이상태의 오염원 농도 측정방법을 개발하였다. 특히 제안식에서는 한계함수량의 개념을 도입하여 전기전도도와 함수량관계를 추정하므로 추정식의 실험값 반영 정도를 증가시켰다. 본 연구에서 제안된 식을 이용하여 추정된 전기전도도와 함수량관계는 다른 제안식에 비하여 개선된 결과를 보여 주었고, 본 연구에서 개발한 오염원 농도 측정법을 이용하여 측정한 결과 함수량이 0.15이하에서는 측정오차가 크지만 함수량이 0.15이상일 경우 매우 좋은 결과를 보였는데 질량평형을 검토한 결과 약 5-10%의 오차율을 보였다. 따라서 본 논문에서 개발된 천이상태의 오염원 농도측정법은 용존 오염물질의 이송에 관한 정확한 실험을 제공할 것으로 판단된다.며, 수질 보전적-환경 보전 차원에서 저수관리 체계를 확고히 할 수 있는 방안을 강구하여야 할 것이다.펄스주입법에 의해 증착된 박박은 강유전성 이력을 나타내었다.지역과 비도시지역을 비교하는 조사 연구가 필요하며, 이러한 조사결과를 바탕으로 자녀의 식습관에 대한 교육을 위한 교재, 교구의 개발과 영양, 식습관 교육프로그램의 개발을 통해 가정과 학교에서 부모와 교사가 자녀의 식생활 지도 관리를 돕고 가정과 교육기관이 연계한 교육 프로그램이 활성화 될 수 있도록 지속적인 관심을 기울여 나가야 할 것이며, 이에 따른