• Proceedings of the Korean Nuclear Society Conference
• /
• 1996.05b
• /
• pp.343-348
• /
• 1996

한국원자력연구소에서는 광범위한 열유동조건에서 CHF 실험을 수행하기 위해 고온, 고압으로 운전할 수 있는 RCS 열수력 Loop를 제작하고 기초 실험자료를 얻기 위해 환상 유로에서 CHF 측정실험을 수행하였다. 실험은 압력 1.82Mpa, 질량유속 300~566kg/$m^2$.s Test Section입구 Subcooling 18$^{\circ}C$ 및 47$^{\circ}C$의 범위에서 수행되었다. CHF 실험자료와 Doerffer의 CHF 상관식을 비교한 결과 상관식은 실험치 보다 최고 160% 크게 예측하였고 Doerffer 상관식은 저유량 영역에서 적용이 어려워질 것으로 예상되었다. 따라서 저유량 영역의 체계적인 CHF 실험자료가 필요하다.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2000.11a
• /
• pp.35-36
• /
• 2000

핵연료의 피복관은 핵분열로부터 발생하는 방사성 핵분열생성물이 외부로 유출되는 것을 차단하는 첫번째 방어막의 역할을 하며, 피복관의 건전성은 정상 상태는 물론 이고 사고시에도 위해한 핵분열생성물의 방출을 억제하는 역할을 충분히 수행할 수 있도록 유지되어야 한다. 단사정 산화막 영역에서만 수증기 압력에 의한 산화가속 효과가 존재하는데, 아직 이를 설명할 수 있는 산화속도 모형이 설정되어 있지 않은 상태이다. 본 연구에선 실험자료를 근거로 하여, 절실히 요구되는 $1000^{\circ}C$ 이하 영역에서 의 수증기 압력을 고려한 산화속도식을 개발하여, 보다 정확한 원전 사고해석이 가능 하도록 하는데 기여하려 한다.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1997.05b
• /
• pp.139-146
• /
• 1997

Zircaloy-4의 수증기 산화와 이에 따른 수소침투의 압력에 대한 영향을 평가하기 위해 pre-transition과 post-transition의 영역에서 1~103 기압의 압력 범위에서 실험을 수행하였다. 그리고 시편의 edge부분에서의 산화율 및 수소침투 가속화 현상을 알아보기 위해 시편의 edge 분율에 따른 산화율 및 수소침투량 실험을 압력영향과 함께 수행하였다. 또 steam corrosion과 waterside corrosion의 비교를 위해 산화율에 따른 수소침투를 평가하였다. 잠정적인 결과로서 pre-transition 영역, 즉, 37$0^{\circ}C$, 72시간에서 103기압에서의 산화가 1 기압에서의 산화보다 약 50% 증가된 값을 가졌고,post-transition 영역, 즉, $700^{\circ}C$, 210분에서는 최고 150%의 산화 가속화를 관찰할 수 있었으며 수소 침투량 역시 산화가 가속화된 만큼 증가하였다. 그리고 압력이 증가함에 따라 산화율이 점진적으로 증가함을 pre-transition영역과 post-transition영역에서 관찰할 수 있었다. 시편의 edge 분율에 따른 산화율의 변화에 대해서는 37$0^{\circ}C$, 72시간의 경우 산화량이 적어 별다른 영향을 관찰할 수 없었으나, $700^{\circ}C$, 210분에서는 시편의 표면적에 대한 edge의 비율이 증가할수록 산화율이 증가하고 있음을 볼 수 있다. 하지만 기존의 논문들에서 주장하고 있는 뚜렷한 edge의 영향을 관측하기는 어려웠다.

• Journal of the Mineralogical Society of Korea
• /
• v.15 no.3
• /
• pp.161-169
• /
• 2002

high pressure and temperature conditions. However, those results are not consistent with one another, and phase boundary between ilmenite and perovskite phases determined only from the quenching method may be not so reliable at all. Therefore, in-situ high pressure-temperature (hP-T) X-ray diffraction measurements were performed up to 19 GPa and $700^{\circ}C$ in a large volume press apparatus using synchrotron radiation. Experimental results show that perovskite phase is stable at pressures above 16 GPa, and transforms back to $LiNbO_3$phase near 15 CPa at room temperature, and that the perovskite-ilmenite transition is back and forth near 15 CPa at $500^{\circ}C$. LiNbO$_3$phase transforms to ilmenite at 13 CPa and $300^{\circ}C$ and at 10.8 CPa and $400^{\circ}C$, respectively. These data indicate that $LiNbO_3$phase may have a stability region in the hP-T phase diagram and that the perovskite-ilmenite phase boundary would be quite different from that previously reported.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.35 no.11
• /
• pp.1377-1382
• /
• 2011

Recently, alternative and novel energy resources have been developed for use in the future because of the current environmental problems and exhaustion of fossil energy resources. Hydrogen energy has many merits, such as its environmental friendliness, easy storage, and easy production, but it also has disadvantages, in that it is highly combustible and explosive. In this study, a test procedure using a simple SP test under highly pressurized hydrogen gas conditions was established. In order to evaluate its applicability, SP tests were carried out using a stainless steel (SUS316L) sample under atmospheric, pressurized helium, and pressurized hydrogen gas conditions. The results under the pressurized hydrogen gas condition showed fissuring and produced a reduction of the elongation in the plastic instability region due to hydrogen embrittlement, showing the effectiveness of the current in-situ SP test.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.4 no.4
• /
• pp.78-86
• /
• 2000

The objective of this research is to understand the characteristics of a nonpremixed, turbulent, hydrogen jet flame which is stabilized in Mach 1.8 coflowing air flows. In order to investigate the flame structure, flame lengths and fuel trajectories were measured by using direct photography, acetone PLIF, Mie scattering techniques, and numerical simulation. Effect of increasing air velocity was investigated when fuel velocity is fixed. The subsonic flame length was decreased drastically, however the supersonic flame length was increased slowly Then the change of flame blow out characteristics was observed as varying fuel nozzle lip thickness. The flame stability can be increased when fuel nozzle lip thickness was increased, which indicates that the minimum fuel lip thickness ratio is required for the stable supersonic flames. Also, it is found that fuel jet is blocked by high pressure zone and low scattering zone is made. Then the fuel that was moving along the recirculation zone had longer residence time within the supersonic flames, which made partially premixed zone.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2005.11a
• /
• pp.341-345
• /
• 2005

This paper is for the combustion characteristics of gas generator which drive 1.5MW-class turbo pump and runs in fuel-rich combustion regime with LOx/kerosene as propellant. The outline of development procedure of real scale high pressure gas generator is introduced and the relation between O/F ratio and outlet temperature and the molecular weight and specific heat ratio of combustion gas are described. The relation between O/F ratio and temperature is newly obtained at higher pressure and the molecular weight and specific heat ratio is modified and their validity is confirmed by the mass relation equation.

• Proceedings of the KSME Conference
• /
• 2001.11b
• /
• pp.330-336
• /
• 2001

Water heat transfer experiments were carried out in a uniformly heated annulus with a wide range of pressure conditions. The local heat transfer coefficients for saturated water flow boiling have been measured just before the occurrence of the critical heat flux (CHF) along the length of the heated section. The trends of the measured heat transfer coefficients were quite different from the conventional understanding for the heat transfer of saturated flow boiling. This discrepancy was explained from the nucleate boiling in the liquid film of annular flow under high heat flux conditions.

• Journal of Welding and Joining
• /
• v.10 no.3
• /
• pp.40-53
• /
• 1992

고온고압장치(High Temperature and Pressure Vessels)의 적용을 위한 기초연구로서 9Cr-1Mo강 용접부의 연화특성에 대하여 검토하였다. 9Cr-1Mo 강재에 Bead-on-Plate용접을 실시한 후, 용접부의 기계적 성질과 그 현미경조직관찰 및 미세경도를 측정한 결과, As-Welded 및 용접 후열처리(PWHT)등의 조건에 관계없이 용접열향부의 변태역과 템퍼링역의 경계에서 모재의 경 도보다 낮은 경도값(연화역)을 나타내었으며 이러한 원인은 결정립계(Grain boundary)에 석출 되는 탄화물의 형성에 의한 뜨임 현상임이 판명되었다.

• Journal of the Korean Society for Railway
• /
• v.19 no.4
• /
• pp.436-444
• /
• 2016

The primary windings of the main transformer for rolling stock have several natural frequencies that can occur internal resonance with transient voltages induced on a high voltage feeding line. Factory testing is limited in its ability to determine whether or not transient voltage with various shape and duration can be excitable. This study presents the design of a high voltage windings model and simulation and analysis of the internal resonant characteristics in terms of the initial voltage distribution and voltage-frequency relationship using the electromagnetic transients program (EMTP). Turn-based lumped-parameters are calculated using the geometry data of the transformer. And, sub-models, being grouped into the total number of layers, are composed using a ladder-network model and implemented by the library function of EMTP. Case studies are used to show the layer-based voltage-frequency relationship characteristics according to the frequency sweep and the voltage escalation and distribution aspects in time-domain simulation.