• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2007.12a
• /
• pp.34-36
• /
• 2007

현재 모형선을 이용한 선형성능 검증방법에는 크게 2가지 방법이 있다. 첫째는 예인수조에서 예인전차를 이용하여 정수중에 배를 예인시켜 그에 따른 저항을 시험하는 방법이 있고, 둘째는 회류수조에서 배를 고정하여 물을 회전시켜 모형선의 저항을 측정하는 방법이 있다. 이와 같은 방법은 저속 및 대형선박을 검증하기 위해 계발된 방법들로 소형 고속어선 및 고속레저선박의 저항성능 평가를 수행하기 어려운 것이 현실이다. 예인전차의 예인속도와 회류수조 물의 유속이 소형 고속어선 및 고속레저선박의 속력에 미치지 못하기 때문이다. 따라서 고속을 요하는 선박의 저항성능 평가를 위해 새로운 방법 연구가 필요하다. 이에 고속선의 저항성능 시험을 위해 실 해상에서 일반 선박을 이용하여 예인하는 방법을 적용하여 저항시험을 수행하였으며 그에 맞는 시스템을 설계하였다.

• Journal of Navigation and Port Research
• /
• v.31 no.10
• /
• pp.813-818
• /
• 2007

There are the C.W.C and Towing Tank to the model-test equipments of the boat. A model testing of the high speed boat have a difficult in the performance verification because of very a small the scale-ratio of the ship-model and restricted by flow-velocity of the C.W.C and X-carriage velocity of the T.T. In general, the stepped hull boat is a high of fuel-efficiency because of the resistance reduction by a small wetted surface-area in correspond without stepped-hull boat. But It have a tendency to be bad the rolling performance by reduced stern wetted-area In this paper, the high speed stepped planning-boats with & without attached a stern body were performed to compare the effect of resistance and rolling performance by using sea model-test method.

• Journal of Navigation and Port Research
• /
• v.34 no.8
• /
• pp.623-628
• /
• 2010

High speed marine vehicle, such as semi-planing, planing craft have been developed recently. These ships paid attention to the resistance characteristics, especially in high speed region. Model test method is divided to two equipment greatly, first 'Towing tank', second 'C.W.C.'. It is difficult to estimate a resistance characteristics for high speed boat. because these are made for low speed ship. This paper suggests a new model test method and system. This is real sea model test and it's comprised of eight part. Firstly, This method is tested at C.W.C that is possible to using in real sea model tes using low speed boat modelt. And then, Real sea model test and CFD calculation are performed and compared with tow way used high speed boat model. It can be a good way to estimate a performance for high speed boat.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.16 no.6
• /
• pp.79-84
• /
• 2012

An experiment of rapid pressurization-induced crack propagation of solid propellant was conducted by using a windowed test chamber. A pre-cracked specimen of solid propellant is installed in the chamber, and highly compressed nitrogen gas in an accumulator pressurizes the chamber until the chamber pressure reaches set-up pressure to make the chamber depressurization. Pressure-time trace was obtained from the experimental result, and pressurization rate was defined from the trace. In this study, three pressurization rates (64.34, 73.86 and 85.44 MPa/s) are considered, and propagation lengths are measured. Also, a progression of the crack propagation recorded by a high-speed digital camera is presented.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2012.05a
• /
• pp.539-544
• /
• 2012

An experiment of rapid pressurization-induced crack propagation of solid propellant was conducted by using a windowed test chamber. A pre-cracked specimen of solid propellant is installed in the chamber, and highly compressed nitrogen gas in a accumulator pressurizes the chamber until the chamber pressure reaches set-up pressure to make the chamber depressurization. Pressure-time trace was obtained from the experimental result, and pressurization rate was defined from the trace. In this study, three pressurization rates (64.34, 73.86 and 85.44 MPa/s) are considered, and propagation lengths are measured. Also, a progression of the crack propagation recorded by a high-speed digital camera is presented.

• Journal of the Society of Naval Architects of Korea
• /
• v.47 no.4
• /
• pp.496-507
• /
• 2010

It is well known that when a high-speed planing craft travels in following seas it experiences long-periodic motions due to low encounter frequency, and it often loses its course keeping stability. Therefore, it is necessary to study the sea-keeping performance and stability of it in the following seas. In this paper, the vertical motions of a planing craft were measured in following regular waves, and the test results were compared with the theoretical results. In the case of the same encounter frequency, non-dimensionalized motion amplitudes become larger as Froude number is higher, and non-dimensionalized motion amplitudes in head waves are larger than those in following waves. The mean values of the motions in following waves are similar to the running attitudes of a craft in calm water at the same Froude number.

• Journal of the Society of Naval Architects of Korea
• /
• v.46 no.4
• /
• pp.373-381
• /
• 2009

The running attitude of a high-speed planing craft may change significantly depending on its speed in seaway. Other variables that may influence its running attitude are its weight, center of gravity, sea conditions, and so on. In this paper, planing craft model tests were carried out with respect to above variables in SNU towing tank, and vertical motion responses of a planing craft in regular head waves were analyzed. The experimental results in regular waves were compared with those in calm water, and compared with the theoretical estimations. Finally, the effects of running speeds of a planing craft on its motion amplitudes are confirmed.

• Journal of Biomedical Engineering Research
• /
• v.19 no.3
• /
• pp.285-290
• /
• 1998

There are various reports on the fracture of mechanical heart valves implanted in human or animal, and they are pointed out that problems are induced by an erosion of disk surface, due to a cavitation effect. We have been investigating this mechanism using accelerated fatigue tester, and it was found that erosion was enhanced by a compliance effect in the test circuit. In this study, effects of compliance value and location on erosion were discussed, while disk closing velocity was measured by a high speed video camera. It was clarified that faster closing velocity was resulting in a enhancement of erosion on the disk surface.

• Journal of the Society of Naval Architects of Korea
• /
• v.46 no.3
• /
• pp.335-342
• /
• 2009

Motion characteristics of a planing craft are sensitively changed according to its weight and longitudinal center of gravity. In this paper, planing craft model tests were performed in calm water for various test conditions and Froude numbers. Sinkage and trim were measured to analyze the relations between the attitudes of a planing craft and the weight and center of gravity of it. Theoretical formula for the prediction of the attitudes of a prismatic planing hull was modified so that it can be applied to the prediction of the attitudes of a non-prismatic planing hull, and the calculation results by the modified formula were in good agreements with the experimental data.

• Journal of Ocean Engineering and Technology
• /
• v.15 no.2
• /
• pp.1-5
• /
• 2001

A study on the new active type oil-water separation system including the oil-water separation system of magnetic film was carried out. Separation system is composed of several active types of circulating oil separation steps and one magnetic film separation step at final stage. At the magnetic separation step, ferrofluid easily forms a weak magnetic mixture with oil, which is from the water by magnetic field gradient. The vessel has been designed to run at the maximum speed of 25 knots. And two typical forms of SWATH and Catamaran have been studied as a new type of oil recovery vessel.