• Transactions of the Korean Society of Mechanical Engineers
• /
• v.18 no.9
• /
• pp.2431-2442
• /
• 1994

In this paper the efficient space marching Viscous Shock Layer and Parabolized Navier-Stokes method have been applied to study the complex 3-D hypersonic equilibrium chemically reacting flowfilelds over sphere-cone($10^{\circ}$) vehicle at low angles of attack($0^{\circ}~5^{\circ}), Mach 20, and an altitude of 35km. The current bluntbody/afterbody space marching numerical method predicts the complex flowfields accurately and efficiently even on a small computer. The shock thickness from equilibrium air model is thinner than that from the perfect gas model. The windside wall heat-transfer rate, pressure and skin friction force were increased significantly when compared with those of leeside. The CA, CN, CM were increased almost linearly with the angle of attack in this region. The wall pressure, heat transfer, skin friction and axial force coeffient from equilibrium model were much higher than those from perfect gas model. The center of pressure moved forward with the increase of angle of attack.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.10a
• /
• pp.795-798
• /
• 1997

This study is about the dynamic behavior of steel(SM45C). Dynamic tests were performed using SHPB(Split Hopkinson Pressure Bar) which is designed and modified to be used in both tensile and compressive modes. Quasi-static compression tests were also carried out for the comparison to the dynamic results. Not only the dynamic mechanical properties but also the effect of the notch of the specimen on stress-strain curve were investigated. The dynamic test results reveal that strain and stress are sensitively affected by the notch. The depth and the number of notch increase the stress and decrease the strain.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.102-106
• /
• 2003

An experimental modal analysis and dynamic stiffness evaluation of a moving body structure of a high speed machining center are presented in this paper. The natural frequencies and corresponding modes, and dynamic compliance of a moving body structure of high speed machining center are investigated by using F.E.M., hydraulic exciter test, and impulse hammer test. The lowest three natural frequencies were found to be 56.6 Hz, 112.7 Hz, and 142.7 Hz by FEA respectively, while those were 55 Hz, 112 Hz, 131 Hz by experimental analysis. Furthermore, both computed and measured absolute dynamic compliances of the moving body structure in iso-direction showed good agreement especially at the first two mode frequencies. With our experimental data, the dynamic characteristics of the machining center can be exploited to get a new development of structural dynamic design and modification.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.1378-1381
• /
• 2003

Recently, high-performance composite materials have been used for various industrial fields because of their superior high strength, high stiffness and lower weight. In this study, manufactured fiber reinforced metal laminate materials are composed of two parts. One is hard-anodized A15083-O alloy as a face material and the other is high strength aramid fiber (Twaron CT709) and polyethylene fiber(Dyneema HB25) laminates as a back-up material. Resistance to penetration is determined by protection ballistic limit(V$\sub$50/, a static velocity with 50% probability for complete penetration) test method. V$\sub$50/ tests with 0$^{\circ}$ obliquity at room temperature were conducted with 5.56mm ball projectiles that were able to achieve near or complete penetration during high velocity impact tests.

• YAKHAK HOEJI
• /
• v.36 no.3
• /
• pp.205-211
• /
• 1992

A simple dignostic method using Fast Atom Bombardment mass spectrometry was applied to the characterization of green tea flavonols from the eluates of Sepahadex LH-20 column chromatography. From the ethyl acetate extracts, crude mixture of flavonol fraction(Fr.$1{\sim}4$) were separated by the stepwise gradient elution with 30, 45, and 60% aqueous acetone. Procyanidine B analogues were found to be typical constituents of Fr. 1. Main components of Fr. 2 were catechins and gallo-catechins. Fr. 3 contained mainly ester type compounds, catechin-gallates, gallocatechin-gallates with their analogues. Fr. 4 was contaminated with some phthalate esters.

• Journal of the Korean Society of Visualization
• /
• v.9 no.1
• /
• pp.55-60
• /
• 2011

Pulsed supersonic liquid jets injected into an ambient air are empirically studied by using a high pressure ballistic range system. Ballistic range systems which are configured with high-pressure tube, pump tube, launch tube and liquid storage nozzle. Experimental studies are conducted to use with various impact nozzle geometry. Supersonic liquid jets are generated by an impact of high speed of the projectile. High speed liquid jets are injected with M = 3.2 which pressure is 1.19 GPa. Multiple jets which accompany with shock wave and pressure wave in front of the jet were observed. The shock-wave affects significantly atomization process for each spray droplets. As decreasing orifice diameter, the averaged SMD of spray jets had the decreasing tendency.

• 한국전산유체공학회:학술대회논문집
• /
• 1998.05a
• /
• pp.190-201
• /
• 1998

The numerical methodology for computing the impact forces of the water entry bodies has been developed. The present method assumed the impact occurs within a very short time interval and the viscous effects do not have time enough to play a significant role in the impact forces, that is, the flow around a water-entry object was assumed as an inviscid potential flow and is solved by the source panel method. The elements fully submerged into the water are routinely treated, but the elements intersected with the effective planar free surface are redefined and reorganized to be amendable to the source panel method. To validate the present code, it has been applied to disk and ogive model and compared with experimental data. Good agreement has been obtained.

• Proceedings of the KSME Conference
• /
• 2003.11a
• /
• pp.574-579
• /
• 2003

The present study addresses an analytical investigation to understand the characteristics of gas flow in the High-Velocity Oxy-Fuel(HVOF) thermal spray gun. One-dimensional analysis is extended to involve the effects of the wall friction and powder particle diameter. From the present analysis it is well known that the flow characteristics inside and outside the thermal spray gun is varied depending on the combustion chamber pressure. The thermal spray gun flow is characterized by six different patterns. The powder particle size and wall friction significantly influence the powder particle velocity. The particle velocity decreases with an increase in the powder particle size. This implies that the combustion chamber pressure should be increased to achieve a higher velocity of the powder particle.

• Proceedings of the Korea Society for Industrial Systems Conference
• /
• 2000.11a
• /
• pp.367-372
• /
• 2000

국내 도시 철도에 차량 견인용으로 사용되는 전동기는 인버터로 구동되는 200㎾급 3상농형 유도 전동기를 표준 사양으로 선정하였으며 열악한 운전 조건에서도 20년을 상회하는 운전 수명을 보장하도록 규정하고 있다. 그러나 PWM 인버터 구동은 견인 전동기에서 추가적인 고조파 발열 손실과 소음, 진동을 초래하며 더욱이 고속 스위칭에 의한 과도 전압과 빠른 상승 시간을 가진 반복 과전압은 인버터와 전동기를 연결하는 케이블 공진 현상에 의해 배가되어 정현파 구동 시에 예상할 수 없었던 매우 커다란 스트레스를 절연 시스템에 가하게 되어 견인 전동기의 예상 수명에 심각한 영향을 미치고 있다. 따라서 본 연구에서는 인버터 구동 견인전동기의 운전수명을 보장하기 위해서는 기존의 시험 방법에 포함되지 않은 PWM 가변속 구동에 따른 고조파 손실과 과도 전압 충격의 문제점을 고려한 새로운 장기 신뢰성 평가기법이 절실히 필요한 상황이기 때문에 이를 제안하고자 하였다.

• 한국방재학회:학술대회논문집
• /
• 2010.02a
• /
• pp.89.2-89.2
• /
• 2010

고속도로에서 주행속도가 높아지게 되면, 도로의 노면 상태에 따라 차량의 안전과 쾌적한 운전자의 환경이 변화될 수 있다. 이처럼 도로의 노면 상태를 결정하는 주된 인자는 도로의 평탄성과 소성변형에 의한 노면의 요철이라고 할 수 있다. 평탄하지 못한 도로를 자동차가 고속으로 주행하게 되면, 자동차의 속도에 의한 도로와의 마찰이 발생하여 자동차에는 매우 큰 흔들림이 발생하게 된다. 또한, 도로의 경우에도 자동차의 차축과 도로면에서 발생하는 충격에 의해 미세한 진동이 발생하게 된다. 그리고 광섬유 브래그 격자(FBG)센서는 외부에서 작용하는 매우 미세한 물리량에 의한 변화의 측정이 가능한 매우 우수한 계측 센서로 사용이 가능하기 때문에 온도보상형 광섬유진동센서를 제작하였고, 이를 고속도로 포장면의 평탄성 모니터링에 활용하고자 하였다.