• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.9 no.1
• /
• pp.1-11
• /
• 2011

Tetraethoxysilane(TEOS) as a silica precursor and hydrochloric acid as an acid catalyst have been used in a surfactant-template synthesis of micrometer-sized mesoporous silica microspheres based on the macroemulsion technique. Increase in the concentration of tetraethoxysilane of the reaction mixture has a serious destructive effect on the particle shape and pore structure. As the acid concentration increases, relatively small microspheres are formed without destroying their spherical morphology of the particles as well as the pore structures. However, due to the attractive interaction between particles in an acidic condition, strong silica agglomerates are formed, and therefore are subject to a post-ultrasonic treatment to separate into an individual single particle.

• The Journal of Engineering Geology
• /
• v.20 no.1
• /
• pp.13-23
• /
• 2010

Toppling failure of a slope is defined as failure behavior accompanying the rotation of rock block which is different from other failure such as sliding along with discontinuities and so on. It generally occurs in the region that discontinuities were developed with inverse dip direction to a slope and it could play a critical role in judging stability of slope. In this study, the stability evaluation was performed about toppling failure on a jointed road cut-slope. To check the deformation behavior, numerical analysis is widely used. However common analysis programs are based on continuum model. Recently, many methods that discontinuity properties can be considered in continuum analysis are suggested. In this study, numerical analysis based on FEM(Finite Element Method) was performed using interface element applied in heterogeneous boundary to simulate effects of discontinuities.

• Journal of Adhesion and Interface
• /
• v.16 no.2
• /
• pp.76-82
• /
• 2015

W/O emulsions were prepared from the aqueous solution containing NIPAAm, MBA, and APS in the continuous phase of toluene and mineral oil mixture with HMP and Span80 by using SPG membrane emulsification, and followed by the formation of PNIPAAm hydrogel microspheres through UV photopolymerization. As the ratio of mineral oil to toluene increased in the continuous phase, both particle size of the hydrogel increased and density of PNIPAAm polymer in the hydrogel particle increased, and which significantly affected swelling/deswelling ratio ($V/V_o$) with temperature change around VPTT. When the polymerization temperature was below LCST ($20^{\circ}C$), PNIPAAm hydrogel showed filled particle morphology; however, it was turned out to hollow particle morphology with thick shell layer with $40^{\circ}C$. Both density of PNIPAAm and gel content of the hydrogel increased with the increase in MBA concentration.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.12 no.2
• /
• pp.67-74
• /
• 2008

This paper provides the test results of bonding behavior of the interface between concrete substrate and carbon fiber in the rehabilitation method applying carbon fiber with epoxy based resin adhesive. The difference in each components was gradually increased subjected to the repetition of temperature variation, regardless of the strength of the substrate concrete, while the ultrasonic interface between each component occurred. An increase in difference of the temperature resulted in a decrease in bond strength of each component. Associated failure mode was shown to be interfacial failure and substrate concrete failure. No remarkable changes were found in the deformation and ultrasonic velocity of each component until the four cycles of the dry and moisture test. Hence, the moisture condition may not affect the bonding behavior of each component. After the repetition of dry and moisture test, corresponding bond strength was reduced to 40% of that before test. For the effect of freeze and thaw test, the cycle of freeze and thaw within 4 cycles resulted in debonding of each component.

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.23 no.2
• /
• pp.118-151
• /
• 1997

Allergic contact dermatitis is a common skin disease resulting from specific immumologic sensitization to topically applied various allergen. Purpose of this study was to investigate skin morphologic chganges by light microscopic, changes of protein band by SDS-PAGE in the skin treated on the surfactant. Furthermore, lectin histochemistry is used to know the chagnges of the terminal sugar of the glycoconjugate in the skin treated on the surfactant. The results were as follows : The 1 day of treated group was indicated the enlargement of capillary, the 3 days of treated group was showed that the cytoplasm was eosinophlic by the pyknotic of nucleus. The 6 days of treated group was observed hyperkeratinoid, increased of inflammation cells to epithelium. The 9 days of treated group was appeares that serum crust was sheded and formed a acanthosis. But dermis layer was cytoplasmic vaculation and enlargement of intercellular space. The 12 days treated group made up new epidermis layer of seven layer and of observed an decreased in quantity of inflammation cells. The mast cell of degranulated type was increased in treated surfactnat. It was secreating granules hold histamin, serotonin and heparin. Accordingly, protein band of electrophortic phase was observed a sudden changes since 3 days treated group. At observeation of the cell-surface glycoconjugates, LCA, PNA, SBA and WGA lectin positive cells but inducated lectin negative cells in Con-A. Furthermore, PNA and SBA showed stroger positive reaction as treated surfactant group.

• Composites Research
• /
• v.16 no.5
• /
• pp.45-53
• /
• 2003

The experimental and numerical investigations on the failure characteristics of the secondary bonded composite single-lap joints were performed. The initiations and growths of cracks were observed using CCD camera and acoustic emission sensor during the tension tests of the joint specimens. The structural behaviors of the specimens were predicted by the geometric nonlinear two-dimensional finite element analysis. The three types of observed initial cracks were included in each finite element models and the strain energy release rates of each specimen models were calculated by VCCT(Virtual Crack Closure Technique) technique. The tension tests showed that the initial cracks occurred in the 60∼90% of final failure loads and the major failure modes of the specimens were adhesive failure and the delamination between the 1st and 2nd ply of laminate. The specimens with the thicker bondline had earlier crack initiation loads but higher crack propagation resistance and eventually better loading capability. The delaminations were mostly observed in the thicker bondline specimens. The mode I values of calculated strain energy release rates were higher than the mode II values in the all specimen models considering the three types of initial cracks. The mode I and total strain energy release rates were calculated as higher values in the order of initial crack in the edge interface, comer interface and delamination between the plies of laminate.

• Korean Journal of Materials Research
• /
• v.10 no.12
• /
• pp.853-863
• /
• 2000

In this study, a new UBM materials system for solder flip chip interconnection of Cu pads were investigated using electroless copper (E-Cu) and electroless nickel (E-Ni) plating method. The interfacial reaction between several UBM structures and Sn-36Pb-2Ag solder and its effect on solder bump joint mechanical reliability were investigated to optimife the UBM materials design for solder bump on Cu pads. Fer the E-Cu UBM, continuous coarse scallop-like $Cu_{6}$ $Sn_{5}$ , intermetallic compound (IMC) was formed at the solder/E-Cu interface, and bump fracture occurred this interface under relative small load. In contrast, Fer the E-Ni/E-Cu UBM, it was observed that E-Ni effectively limited the growth of IMC at the interface, and the Polygonal $Ni_3$$Sn_4$ IMC was formed because of crystallographic mismatch between monoclinic $Ni_3$$Sn_4$ and amorphous E-Ni phase. Consequently, relatively higher bump adhesion strength was observed at E-Ni/E-Cu UBM than E-Cu UBM. As a result, it was fecund that E-Ni/E-Cu UBM material system was a better choice for solder flip chip interconnection on CU PadS.

• Journal of Conservation Science
• /
• v.28 no.1
• /
• pp.21-27
• /
• 2012

In the Chosun period, the noble class usually buried the dead bodies in the lime-covered tomb. Recently their costumes are excavated while maintaining the shape. However, the textiles discovered from the inside have been degradated by a body and moisture. To conserve these textiles one of the most important thing is how to clean these textiles right after the excavation. The purpose of this study is to examine the effects of wet cleaning to minimize the color change of textile remains. For this purpose, silk and cotton were dyed with natural dyes (7 red, 1 blue, 6 yellow, 4 green and 4 purple colors), then they were kept for 6 months with pork meat at $10^{\circ}C$, and were washed by four cleaning solutions (water, anionic surfactant (SDS), non-ionic surfactant (Triton X-100) and natural surfactant (saponin)) at $20^{\circ}C$ and $40^{\circ}C$. The color change was evaluated by color difference (${\Delta}E$) between non-treated and after washed samples. From the results, it was found that the color changes are significantly different depending on the washing temperature, textile material, the cleaning agents and the type of dyes.

• Journal of Adhesion and Interface
• /
• v.9 no.3
• /
• pp.20-26
• /
• 2008

It is well know that the structure of shape memory alloy (SMA) can change from martensite austenite by either temperature or stress. Due to their inherent shape recovery properties, SMA fiber can be used such as for stress or cure-monitoring sensor or actuator, during applied stress or temperature. Incomplete superelasticity was observed as the stress hysteresis at stress-strain curve under cyclic loading test and temperature change. Superelasticity behavior was observed for the single-SMA fiber/epoxy composites under cyclic mechanical loading at stress-strain curve. SMA fiber or epoxy embedded SMA fiber composite exhibited the decreased interfacial properties due to the cyclic loading and thus reduced shape memory performance. Rigid epoxy and the changed interfacial adhesion between SMA fiber and epoxy by the surface treatment on SMA fiber exhibited similar incomplete superelastic trend. Epoxy embedded single SMA fiber exhibited the incomplete recovery during cure process by remaining residual heat and thus occurring residual stress in single SMA fiber/epoxy composite.

• Proceedings of the Korean Society of Dyers and Finishers Conference
• /
• 2011.03a
• /
• pp.55-55
• /
• 2011

실리카 지지체 위에 은 (silver) 나노 입자를 부착시키는 방법으로는 지지체 표면을 먼저 은입자와 친화성이 큰 amino(-NH2), mercapto(-SH), cyan(-CN) 등의 관능기로 표면처리 하는 방법이 일반적으로 사용된다. 구체적으로 설명하면 첫 단계로 지지체인 실리카입자의 표면을 아민으로 표면 처리 한다. 실리카 입자위에 부착된 아민관능기는 입자 생성의 단계에서 은 (silver) 나노 입자가 붙는 접촉점의 역할과 핵 생성 장소로서의 역할을 하게되고, 아민 관능기의 이런 역할로 실리카 입자 표면에 부착된 핵이 생장하여 입자가 됨으로써 최종적으로 은(silver) 나노 입자가 실리카 지지체위에 부착된 형태의 나노복합체가 형성된다. 분자량이 다른 PVP를 사용하여 제조한, NH2와 SH로 계면처리 된 은-실리카 나노복합체제조를 시도하였다. 사용되는 PVP의 분자량이 증가함에 따라 긴 고분자 사슬에 의하여 생성된 입체장애가 증가하게 되어, 은 핵의 성장에 대한 물리적 장벽이 증가하게 된다. 그러므로 고정화된 은 입자의 크기가 감소하게 된다. 이러한 형상은 NH2기 또는 SH기로 계면 처리된 실리카를 이용하여 제조된 은-실리카 나노복합체 입자들에서 모두 관찰되지만, SH기로 계면처리된 실리카를 사용할 경우 고정화된 은 입자의 수가 더욱 많고, 크기 역시 더욱 균일함을 알 수 있다.