• Journal of the Microelectronics and Packaging Society
• /
• v.25 no.2
• /
• pp.41-48
• /
• 2018

The quantitative interfacial adhesion energy measurement method of copper redistribution layer and WPR dielectric interface were investigated using $90^{\circ}$ peel test, 4-point bending test, double cantilever beam (DCB) measurement for FOWLP Applications. Measured interfacial adhesion energy values of all three methods were higher than $5J/m^2$, which is considered as a minimum criterion for reliable Cu/low-k integration with CMP processes without delamination. Measured energy values increase with increasing phase angle, that is, in order of DCB, 4-point bending test, and $90^{\circ}$ peel test due to increasing roughness-related shielding and plastic energy dissipation effects, which match well interfacial fracture mechanics theory. Considering adhesion specimen preparation process, phase angle, measurement accuracy and bonding energy levels, both DCB and 4-point bending test methods are recommended for quantitative adhesion energy measurement of RDL interface depending on the real application situations.

• Journal of the Microelectronics and Packaging Society
• /
• v.25 no.3
• /
• pp.7-12
• /
• 2018

The effects of Ru deposition temperature and post-annealing conditions on the interfacial adhesion energies of atomic layer deposited (ALD) Ru diffusion barrier layer and Cu thin films for the advanced Cu interconnects applications were systematically investigated. The initial interfacial adhesion energies were 8.55, 9.37, $8.96J/m^2$ for the sample deposited at 225, 270, and $310^{\circ}C$, respectively, which are closely related to the similar microstructures and resistivities of Ru films for ALD Ru deposition temperature variations. And the interfacial adhesion energies showed the relatively stable high values over $7.59J/m^2$ until 250h during post-annealing at $200^{\circ}C$, while dramatically decreased to $1.40J/m^2$ after 500 h. The X-ray photoelectron spectroscopy Cu 2p peak separation analysis showed that there exists good correlation between the interfacial adhesion energy and the interfacial CuO formation. Therefore, ALD Ru seems to be a promising diffusion barrier candidate with reliable interfacial reliability for advanced Cu interconnects.

• Journal of the Korea Concrete Institute
• /
• v.21 no.6
• /
• pp.781-788
• /
• 2009

Mechanical properties of steel-concrete interface were evaluated on the basis of experimental observations. The properties included bond strength, unbounded and bonded friction angles, residual level of friction angle, mode I fracture energy, mode II bonded fracture energy and unbonded slip-friction energy under different levels of normal stress, and shape parameters to define geometrical shape of failure envelope. For this purpose, a typical type of constitutive model of describing steel-concrete interface behavior was presented based on a hyperbolic three-parameter Mohr-Coulomb type failure criterion. The constitutive model depicts the strong dependency of interface behavior on bonding condition of interface, bonded or unbounded. Values of the interface parameters were determined through interpretation of experimental results, geometry of failure envelope and sensitivity analysis. Nonlinear finite element analysis that incorporates steel-concrete interface as well as material nonlinearities of concrete and steel were performed to predict the experimental results.

• 한국신재생에너지학회:학술대회논문집
• /
• 2011.05a
• /
• pp.103.1-103.1
• /
• 2011

실리콘 이종접합 태양전지에서 계면 결함 밀도는 효율을 결정하는데 가장 중요한 요인으로 작용한다. 계면 결함은 캐리어의 재결합 위치로 작용하여, 계면 결함 밀도가 증가하면 재결합 속도가 증가하게 된다. 흡수층으로 사용되는 실리콘 웨이퍼 (결정질 실리콘)를 가능한 깨끗하게 세정함으로써, 또한 emitter로 쓰이는 비정질 실리콘을 낮은 데미지로 증착하여 계면 결함 밀도를 감소 시킬 수 있다. 이러한 계면 결함 밀도의 감소가 어떠한 변화로 인해 태양전지 특성에 영향을 주는지 시물레이션을 통해 알아보았다. n-type 웨이퍼에 p-type 비정질 실리콘을 emitter로 하여 TCO/p/i/n-type wafer/i/n/TCO/metal의 구조를 적용했고, wafer 전면과 i로 쓰인 무첨가된 비정질 실리콘 간의 계면 결함 밀도를 변수로 적용했다. 그 결과, 계면 결함 밀도가 감소함에 따라 재결합이 감소하여 태양전지 특성이 증가하는 측면도 있지만, 흡수층의 장벽 (barrier height)이 높아져 재결합을 더욱 감소시킴으로 인해 태양전지 특성이 증가함을 알 수 있었다.

• Journal of the Microelectronics and Packaging Society
• /
• v.30 no.2
• /
• pp.52-59
• /
• 2023

The effects of dielectric curing temperature and temperature/humidity treatment conditions on the interfacial adhesion energies between Ti diffusion barrier/polybenzoxazole (PBO) dielectric layers were systematically investigated for Cu redistribution layer applications of fan-out wafer level package. The initial interfacial adhesion energies were 16.63, 25.95, 16.58 J/m² for PBO curing temperatures at 175, 200, and 225 ℃, respectively. X-ray photoelectron spectroscopy analysis showed that there exists a good correlation between the interfacial adhesion energy and the C-O peak area fractions at PBO delaminated surfaces. And the interfacial adhesion energies of samples cured at 200 ℃ decreased to 3.99 J/m² after 500 h at 85 ℃/85 % relative humidity, possibly due to the weak boundary layer formation inside PBO near Ti/PBO interface.

• Journal of the Microelectronics and Packaging Society
• /
• v.21 no.1
• /
• pp.45-50
• /
• 2014

Effects of wet chemical treatment and thermal cycle conditions on the quantitative interfacial adhesion energy of $Cu/SiN_x$ thin film interfaces were evaluated by 4-point bending test method. The test samples were cleaned by chemical treatment after Cu chemical-mechanical polishing (CMP). The thermal cycle test between Cu and $SiN_x$ capping layer was experimented at the temperature, -45 to $175^{\circ}C$ for 250 cycles. The measured interfacial adhesion energy increased from 10.57 to $14.87J/m^2$ after surface chemical treatment. After 250 thermal cycles, the interfacial adhesion energy decreased to $5.64J/m^2$ and $7.34J/m^2$ for without chemical treatment and with chemical treatment, respectively. The delaminated interfaces were confirmed as $Cu/SiN_x$ interface by using the scanning electron microscope and energy dispersive spectroscopy. From X-ray photoelectron spectroscopy analysis results, the relative Cu oxide amounts between $SiN_x$ and Cu decreased by chemical treatment and increased after thermal cycle. The thermal stress due to the mismatch of thermal expansion coefficient during thermal cycle seemed to weaken the $Cu/SiN_x$ interface adhesion, which led to increased CuO amounts at Cu film surface.

• Applied Chemistry for Engineering
• /
• v.29 no.5
• /
• pp.524-532
• /
• 2018

In this study, two types of amino acids-based anionic biosurfactants such as potassium cocoyl glutamate (CTK) and sodium cocoyl glutamate (CTN) were synthesized from coconut oils and the structure elucidation of CTK and CTN was carried out by using FT-IR, $^1H-NMR$ and $^{13}C-NMR$ spectrophotometries. Measurements of interfacial properties such as static and dynamic surface tensions and emulsification activity showed that both CTK and CTN were surface-active and effective in lowering the interfacial free energy. In particular, the CTK surfactant was found to be more efficient in reducing the interfacial free energy since the larger number of CTK molecules was preferentially adsorbed at the air-water interface due to the higher hydrophobicity and larger mobility of CTK than those of using CTN, indicating possible uses in cosmetics and household products formulation.

• Journal of the Korean Vacuum Society
• /
• v.2 no.3
• /
• pp.339-345
• /
• 1993

계면의 원자구조와 전자특성간의 상관성을 연구하기 위하여 GaAs-Ge(AlAs) 이종접합에서 전자의 국소상태밀도(LDOS)를 계산하였다. 본 연구에서는 tight-binding recursion 방법을 기초로 하여 계면의 국소상태밀도로부터 band-offsets, 계면형성에너지, 계면결합의 bond order 등을 연구하는 보다 편리한 방법을 제시하였다.

• Magazine of the Korea Concrete Institute
• /
• v.11 no.2
• /
• pp.177-186
• /
• 1999

The purpose of this study is to analyze the interface debonding of RC beams strengthened by carbon fiber sheet(CFS). The behavior of damaged RC beams strengthened with CFS is analytically investigated next using linear elastic fracture mechanics(LEFM) approach and the finite element method. The study includes an investigation of the separation mode by interface fracture of the strengthening materials due to the interfacial shear and normal stresses. The numerical method is presented to obtain the value of interfacial fracture parameter such as the strain energy release rate. Based on the results of this study, it is found that the critical case occurs when the interfacial cracks occur within a short region of the flexural crack. The CFS strengthening has not an adequate factor of safety against interfacial debonding of CFS. Furthermore, for the thicknesses of the adhesive studied[1mm~3mm], it is no noticeable effect on the strain energy release rate.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.11a
• /
• pp.72.2-72.2
• /
• 2010

평판형 고체산화물 연료전지 스택의 고온 밀봉 구조에 대하여 설명하고 스택 운전 후 사후 분석을 통하여 밀봉재와 금속 분리판의 계면반응에 대하여 고찰하였다. 대표적인 고온 밀봉재인 Barium-Silicate 계 결정화 유리와 Fe-Cr 계 금속 분리판은 스택의 작동온도인 $700{\sim}850^{\circ}C$ 에서 고온 반응을 통하여 계면에 반응생성물을 형성하는 것이 확인되었다. 이러한 계면반응은 장기 운전시 SOFC 스택 성능 저하의 원인이 되고, 열 싸이클(작동온도${\leftrightarrow}$상온)을 가하면 계면반응 생성물이 delamination 되어 밀봉구조가 파괴되어 수명을 단축시키게 된다. 계면반응은 Fe-Cr 계 금속 분리판의 산화물인 Cr 산화물, Fe 산화물이 밀봉유리 소재와 반응을 일으키는 것이 주요 원인으로 판명되었다. SOFC 스택에서 열 싸이클시 계면반응에 의하여 기밀도가 감소하는 현상이 확인되었으며, 밀봉 구조의 어느 부분에서 계면반응이 진행되는지 관찰하였다. 이러한 계면반응을 막기 위해서는 금속 분리판과 밀봉유리 사이에 계면반응을 억제하는 보호층을 형성하는 방법이 효과적이다. 본 연구에서는 보호층으로서 밀봉유리 및 Fe-Cr 계 금속 분리판과의 계면반응성이 낮고 열팽창 계수가 비슷한 Yttria Stabilized Zirconia 층을 APS(Atmospheric Plasma Spray) 공정을 이용하여 형성하였다. 밀봉유리/YSZ 보호층/금속분리판은 gas-tight 한 밀봉 구조를 형성하였으며, YSZ 보호층은 밀봉유리와 Fe-Cr 계 금속 분리판 소재와 계면반응을 효과적으로 억제하는 것이 확인되었다.