• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.13 no.4
• /
• pp.351-358
• /
• 2002

To determine a scattering performance of a rectangular waveguide with two skewed conducting posts in approximation by the mode matching method and the generalized scattering method is presented in this paper. We determined the optimized result from effective analysis to select the adequate eigenmode number in mode matching method for the skewed two conducting posts. And we obtained the scattering performance of the junction of the waveguide to coaxial line with two skewed conducting posts by application of above method. By this result, it can be seen that the transmission performance at output port of waveguide to coaxial line is 3 ㏈ at the angle, 50°And we obtained the reflection performance to decrease linearly along the skewed angle at input port.

• Water for future
• /
• v.28 no.3
• /
• pp.197-204
• /
• 1995

The runoff from an urban catchment is increased because of the gravitation of the population towards cities. For this reason, water level increment in confluence area makes it impossible to drain internal water and thus produces flood out in upstream areas. In this study, flow variations of main channel are measured which is caused by combining storm sewer into main channel in small watershed. Depth increment in main stream is analyzed due to flowrate and slope in main channel and flowrate, slope is getting steeper, and also due to low flowrate in main stream and high flowrate in tributrary channel. For the degree of confluence, depth ratio decreases when the degree is getting small. As mentioned above, main factors influencing the depth ratio increment of confluence channel are in the order of the degree of confluence, and the flowrate of tributary channel and main channel.

• Journal of Energy Engineering
• /
• v.12 no.2
• /
• pp.139-144
• /
• 2003

Augmentation of CHF by ultrasonic vibration in water pool is experimentally investigated under pool boiling condition. The experiments are carried out using copper coated plates and distilled water. Measurements of CHF on flat plate heated surface were made with and without ultrasonic wave and with variations in inclined angle of the surface and water subcooling. Experimental apparatus consists of a bath, power supply, test section, ultrasonic generator, and data acquisition system. The measurements show that ultrasonic wave enhances CHF and its extent is dependent upon inclination angle as well as water subcooling. The rate of increase in CHF increases with an increase in water subcooling while it decreases with an increase in inclination angle. Visual observation shows that the cause of CHF augmentation is closely related with the dynamic behavior of bubble generation and departure in acoustic field.

• Journal of the korean Society of Automotive Engineers
• /
• v.10 no.4
• /
• pp.85-96
• /
• 1988

The optimum cutting condition for rake angle in turning was investigated in (6-4) Brass and Al alloy. Results of experiments in (6-4) Brass and Al alloy are as follow. Specific cutting resistance becames higher as the depth of cutting, feed or cutting velocity decreases at same rake angle and resistance appear low value 20.deg., 25.deg.(6-4)brass, 0.deg. 20.deg.(Al alloy). The optimum cutting condition for(6-4) Brass is depth of cutting 0.5mm, rake angle 25.deg., cutting velocity 80m/min, feed 0.1mm/rev and for Al alloy is depth of cutting 0.1mm, rake angle 0.deg., cutting velocity 200m/min, feed 0.5mm/rev. The rake angle for good roughness is 20.deg. at (6-4) Brass, and that for Al alloy is 15.deg. The roughness is influenced by feed and it has the lowest value at 0.1mm/rev and the cutting condition is influenced by rake angle only.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 2002.02a
• /
• pp.158-166
• /
• 2002

진공관형 태양열집열기의 집열성능 및 집열특성 실험을 통하여 다음과 같은 결론을 얻을 수 있었다. 1) 집열성능 실험을 통하여 진공관형 태양열집열기의 순간집열효율이 60%로 높게 나타났다. 2) 진공관형 태양열집열기의 집열특성 실험에 의해 얻어진 결론은 다음과 같다. \circled1 경사각 0$^{\circ}$일 때 집열기에 조사된 광 강도는 630W/m$^2$이었으며, 5시간 24분의 광 조사 후 초기온도에 비해 물탱크내의 물 132$\ell$를 8.1$^{\circ}C$ 상승시켰다. \circled2 경사각 $10^{\circ}$일 때 광강도는 615W/m$^2$이었으며, 5시간 24분의 광 조사 후 초기온도에 비해 물탱크내의 물의 온도를 7.3$^{\circ}C$ 상승시켰다. \circled3 경사각 20$^{\circ}$일 때 광 강도는 605W/m$^2$이었으며, 5시간 24분의 광 조사 후 초기온도에 비해 물탱크의 물 132$\ell$을 6.6$^{\circ}C$ 상승시켰다. 집열기에 대한 솔라시뮬레이터의 경사각이 작을수록 광 강도가 커 물탱크내의 물 온도를 크게 상승시키는 것으로 나타났다.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.32 no.5
• /
• pp.84-90
• /
• 2004

A prediction of SEE rates for a candidate microprocessor is made based on the ground experiment results with a proton accelerator. Populations of charged particles in space are estimated with numerical models such as AP8, JPL91 and CREME. The cross section curves that are previously obtained with the accelerator are then employed for SEE prediction. Both the high and low inclinations are considered for low-earth orbits with nominal altitudes of about 685km. The results show that the occurrence rate of SEEs for the candidate device is acceptable for low-inclinations, but can be considerable under worst conditions for high inclinations.

• Tunnel and Underground Space
• /
• v.16 no.2 s.61
• /
• pp.166-178
• /
• 2006

Recently, the frequency of occurring dynamic events such as earthquakes, explosives blasting and other types of vibration has been increasing. Besides, the chances of exposure for rock discontinuities to free faces get higher as the scale of rock mass structures become larger. For that reason, the frictional behavior of rock joints under dynamic conditions needs to be investigated. In this study, artificially fractured rock joint specimens were prepared in order to examine the dynamic frictional behavior of rough rock joint. Roughness of each specimen was characterized by measuring surface topography using a laser profilometer and a series of shaking table tests was carried out. For mated joints, the static friction angle back-calculated ken the yield acceleration was $2.7^{\circ}$ lower than the tilt angle on average. The averaged dynamic friction angle for unmated joints was $1.8^{\circ}$ lower than the tilt angle. Displacement patterns of sliding block were classified into 4 types and proved to be related to the first order asperity of rock joint. The tilt angle and the static friction angle for mated joints seem to be correlated to micro average inclination angle which represents the second order asperity. The tilt angle and the dynamic friction angle for unmated Joints, however, have no correlation with roughness parameters. Friction angles obtained by shaking table test were lower than those by direct shear test.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.35 no.3
• /
• pp.237-244
• /
• 2011

An experimental study was carried out to investigate the effect of the inclination angle on the nucleate pool boiling of saturated water at atmospheric pressure. We considered an annulus with a gap of 5 mm and a bottom opening. The inner tube of the annulus was heated, and the outer diameter and the length of the tube were 25.4 mm and 500 mm, respectively. The inclination angle was varied from horizontal to vertical. The results were compared to those for an annulus with a larger gap and a single tube. In the small-gap annulus, the effect of the inclination angle on the heat transfer was not significant. However, an early onset of the critical heat flux was observed at 80 kW/$m^2$ when the annulus was horizontal. Liquid agitation and bubble coalescence were considered to be the major heat-transfer mechanisms.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.30 no.4
• /
• pp.1-9
• /
• 2002

There is the high possibility of crack initiation from mechanical joints, which are widely used in aircraft fuselages, due to the development of stress concentration and contact pressure. In this paper, the mixed-mode stress intensity factors at the surface and deepest points of an inclined quarter elliptical corner crack in mechanical joints are analyzed by the weight function method. The coefficients included in the weight function are obtained by finite element analyses for reference loadings. Critical angle at which mode I stress intensity factor becomes maximum is determined by analyzing the variation of stress intensity factors along incline angle of crack and the effects of the amount of clearance and crack depth on the critical angle are investigated.

• Fire Science and Engineering
• /
• v.20 no.4 s.64
• /
• pp.135-142
• /
• 2006

The experiment applied Positive Pressure Ventilation to rapidly exhaust heat and smoke inside the construction in the fire was done. Changes of heat discharge and smoke density were measured, with the various blowing condition like a fan tilting angle to find the effect of the parameter. Experimental apparatus were with PPV and water mist system for better efficiency, and investigate the effect of heat discharge and smoke removal. In the experiment, flame temperature has decreased when PPV was applied. Smoke density, generated from fire also decreased dramatically and the efficiency showed the highest rate at $0^{\circ}$ tilting angle. In addition, combination of PPV and water mist system highly improved the efficiency of evacuation on heat and smoke density, clearly was influenced by the tilting angle.