• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.40 no.8
• /
• pp.527-533
• /
• 2016

A new empirical correlation was developed to identify the effect of an inclination angle on pool boiling heat transfer coefficient of a tube submerged in the saturated water at atmospheric pressure. Through the experiments and the survey of published results 431 data points were obtained and the nonlinear least square method was used as a regression technique. The heat flux of the tube($0{\sim}120kW/m^2$), inclination angle($0^{\circ}{\sim}90^{\circ}$), and the length divided by the diameter of a tube(18~42.52) were selected as major parameters. The newly developed correlation well predicts the experimental data within ${\pm}18%$, with some exceptions.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.24 no.5
• /
• pp.591-596
• /
• 2018

In Designing a Small Ship, the Design of the Trim for Sailing has a great influence on the Stability of the Ship as well as Resistance. The Center of Gravity of a Ship is mostly determined during Initial Design. This Study confirms the Effect of Trim on changes in Vertical Center of Gravity by Numerical Analysis for a Small Catamaran. The Results were examined in a Model test. However, No Model tests were conducted while varying the changes in Vertical Center of Gravity. Nonetheless, Investigation was completed for the Purpose of presenting Vertical Center of Gravity results according to plans for the Trim during Initial Design of a Small Ship. In order to verify the Results of Numerical Analysis, a Comparison with Experimental results was carried out. Alternation of Trim angle and Resistance performance according to changes in the Center of Gravity were studied.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.22 no.3
• /
• pp.149-155
• /
• 2010

The existing formula for estimating the wave overtopping are mainly about the perpendicularly incident wave to the structure and wave overtopping formula for the obliquely incident wave are rare. Moreover, these formula present only the overtopping reduction factor(${\gamma}_{\beta}$) with respect to the incident wave angle rather than the spatial distribution of overtopping along the structures because the length of model is relatively too short for the wave to propagate along the structure. In this study, the wave overtopping reduction factor considering the spatial variation of wave overtopping along the vertical wall is investigated using the hydraulic model tests and the results are compared with the those of EurOtop(2007). The wave overtopping reduction factor is modified for ${\beta}$ > $45^{\circ}$ condition.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2016.05a
• /
• pp.108-109
• /
• 2016

It is very important to fully understand the concepts, causes and corrections of ship's transverse inclination which is classified into Heel, List and Loll. Particularly, it is presumed that some recent disaster at sea is related to negative GM developed by the loss of stability during sailing. In this study, actual 'Angle of Loll' is simulated by model-ship experiment and the result is compared with calculated value under same condition. Furthermore, how to distinguish Loll from List and the way to correct the 'Angle of Loll' for officers are described.

• Proceedings of the KAIS Fall Conference
• /
• 2007.05a
• /
• pp.99-103
• /
• 2007

정확하고 신뢰성 높은 유량 자료는 수자원의 정량적인 계획과 관리에 필수적이다. 이를 위하여 Chiu는 기존의 결정론적인 흐름 방향 유속분포식의 한계를 극복할 수 있는 방법으로 확률통계에서 사용되는 엔트로피 개념을 이용한 3차원 유속분포 식을 제안하였고, 이를 실험실 데이터와 자연하천에 적용하여 신뢰성과 정확성을 지속적으로 증명하여 마침내 이에 대한 활용성이 매우 크게 대두되어 Chiu의 유속공식을 적극적으로 사용하고 있는 실정이다. 그러나 지금까지 이론적인 유속 분포식을 검증하기 위하여 단면 형상이 일정한 직사각형이나 사다리꼴 동의 실험수로에서부터 불규칙한 단면 형상을 갖는 자연 하천에 대한 적용을 거의 이루고 있는 실정이나, 하상경사가 변하는 경우에도 엔트로피 파라미터(M)가 이에 대응하여 평형상태에 도달하려고 하는지에 대한 연구는 전무하다. 본 연구에서는 하상경사를 임의로 변경 가능한 실험수로를 선택하여 정밀법에 의한 유속측정을 실시하였다. 같은 지점의 같은 단면에서 하상경사(${\Theta}$)가 0.000935부터 0.025794까지 28번의 경사변화를 주고 각 경사마다 유량을 측정하여 28개의 유량측정 데이터를, Chiu의 엔트로피 유속공식에 적용하여, 평균유속과 최대유속 사이의 관계가 선형관계, 즉 하상경사가 변하는 경우에도 엔트로피 파라미터(M)가 이에 대응하여 평형상태에 도달함을 증명하였다.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.10 no.1
• /
• pp.23-29
• /
• 2006

In an annular injection supersonic ejector, the supersonic primary flow is injected along the side wall, therefore a funnel-shaped shock wave is generated by the contraction angle of the mixing chamber. In the present study, we developed a simple funnel shock wave model using 2-D wedge and conical shock wave relations. In result, the secondary flow pressure can be predicted more accurately than using a simple 2-D wedge shock wave model. Through the same analysis, the compression ratio and the adiabatic efficiency according to the entrainment ratio were calculated.

• Proceedings of the KAIS Fall Conference
• /
• 2007.11a
• /
• pp.116-119
• /
• 2007

정확하고 신뢰성 높은 유량 자료는 수자원의 정량적인 계획과 관리에 필수적이다. 이를 위하여 Chiu는 기존의 결정론적인 흐름 방향 유속분포식의 한계를 극복할 수 있는 방법으로 확률통계에서 사용되는 엔트로피 개념을 이용한 3차원 유속분포 식을 제안하였고, 이를 실험실 테이터와 자연하천에 적용하여 신뢰성과 정확성을 지속적으로 증명하여, 마침내 이에 대한 활용성이 매우 크게 대두되어 Chiu의 유속공식을 적극적으로 사용하고 있는 실정이다. 그러나 지금까지 이론적인 유속 분포식을 검증하기위하여 단면 형상이 일정한 직사각형이나 사다리꼴 등의 실험수로에서부터 불규칙한 단면 형상을 갖는 자연 하천에 대한 적용을 거의 이루고 있는 실정이나, 하상경사가 변하는 경우에도 엔트로피 파라미터(M)가 이에 대응하여 평형상태에 도달하려고 하는지에 대한 연구는 전무하다. 본 연구에서는 하상경사를 임의로 변경 가능한 실험수로를 선택하여 정밀법에 의한 유속측정을 실시하였다. 같은 지점의 같은 단면에서 하상경사($\theta$)가 0.00069부터 0.019034까지 28번의 경사변화를 주고 각 경사마다 유량을 측정하여 28개의 유량측정 데이타를, Chiu의 엔트로피 유속공식에 적용하여, 평균유속과 최대유속 사이의 관계가 선형관계, 즉 하상경사가 변하는 경우에도 엔트로피 파라미터(M)가 이에 대응하여 평형상태에 도달함을 증명하였다.

• Journal of the Korea Convergence Society
• /
• v.11 no.2
• /
• pp.53-60
• /
• 2020

The purpose of this paper is to evaluate the image of the Styrofoam Wedge that can minimize the position change by supporting the wrist during the True PA and lateral examination of the wrist. In 50 people, the gap between the distal radius joint facet and the wrist bone was measured after the wrist True PA and lateral images were obtained using a general examination(vertical), tube angle(vertical:10°, lateral:20°) and Styrofoam Wedge(vertical). When joint spacing was measured in the True PA and lateral images of the wrist, general examination(5.54mm, 9.42mm), tube angle(2.05mm, 5.07mm) and Styrofoam Wedge(1.79mm, 5.46mm) were shown to be small. The smaller the joint spacing, the easier it is to observe that is open. Therefore, True PA and lateral imaging of the wrist Styrofoam Wedge can reduce the distortion of the image and thus acquire images of high diagnostic value. In addition, it may be possible to reduce the deviation caused by the change of patient's position during re-projection.

• Korean Journal of Optics and Photonics
• /
• v.10 no.6
• /
• pp.500-506
• /
• 1999

We designed and fabricated a bidirectional optical transceiver module for low cost access network. An integrated chip forming a pin-PD on an 1.3 urn FP-LD was assembled by flip-chip bonding on a Si optical bench, a single mode fiber with an angled end facet was aligned passively with the integrated chip on V-groove of Si-optical bench. Gaussian beam theory was applied to evaluate the coupling coefficients as a function of some parameters such as alignment distance, angle of fiber end facet, vertical alignment error. The theory is also used to search the bottle-neck between transmittance and receiving coupling efficiency in the bi-directional optical system. Tn this paper, we confirmed that reduction of coupling efficiency by the vertical alignment error between laser beam and fiber core axis can be compensated by controlling the fiber facet angle. In the fabrication of sub-module, a'||'&'||' we made such that the fiber facet have a corn shape with an angled facet only core part, the reflection of transmitted laser beam from the fiber facet could be minimized below -35 dE in alignment distance of 2: 30 /J.m. In the same condition, transmitted output power of -12.1 dEm and responsivity of 0.2. AIW were obtained.

• The Journal of Korean Academy of Prosthodontics
• /
• v.55 no.1
• /
• pp.9-17
• /
• 2017

Purpose: The purpose of this study was to evaluate the fracture strength of straight and angled zirconia abutments for internal hex and external hex implants. Materials and methods: Twenty internal hex implants and 20 external hex implants were prepared. The prefabricated straight zirconia abutments and 17-degree-angled zirconia abutments were connected to those 40 implants. The specimens were classified into 4 groups depending on the connection type and abutment angulation; internal hex implant/straight abutment, group INS; internal hex implant/angled abutment, group INA; external hex implant/straight abutment, group EXS; external hex implant/angled abutment, group EXA. All specimens were loaded at a 30-degree angle with a crosshead speed of 1 mm/min using universal testing machine. The fracture loads were analyzed using 2-way ANOVA and independent t-test (${\alpha}=.05$). Results: The mean fracture load for INS was 955.91 N, 933.65 N for INA, 1267.20 N for EXS, and 1405.93 N for EXA. External hex implant showed a significantly higher fracture load, as compared to internal hex implant (P < .001). No significant differences in fracture loads were observed between the straight and angled abutment in internal hex implants (P = .747) and external hex implants (P = .222). Internal hexes of abutments were fractured horizontally in internal connection implants, while lingual cervical neck portions were fractured in external connection implants. Conclusion: The zirconia abutments with external hex implants showed significantly higher fracture strength than those with internal hex implants. However there was no difference in fracture strength between the straight and 17-degree-angled zirconia abutment connected to both implant systems.