• Journal of the Korean GEO-environmental Society
• /
• 제13권3호
• /
• pp.29-37
• /
• 2012

This study is to find out the characteristics of the behavior of Geosyntehtic Reinforced Retaining Earth Wall(GRREW) through the laboratory experiment with the reduced-scale model, and to verify the effect of reinforcement by materials of GRREW. The loading tests after combining nonwoven geosynthetic, re-bar mesh nets and drainage blocks respectively among the components of the GRREW were performed in three cases of their slopes. In the cases of the behavior analysis including all of the components of the GRREW, the maximum horizontal displacement was generated 8.4mm at the location of 0.57H in the slope of 1:0.3; 3.8mm at the location of 0.57H in the slope of 1:0.6; 3.6mm at the location of 0.86H in the slope of 1:1.0. On average, the horizontal displacements of the GRREW were reduced by 83.8% against those of the original slopes. Lastly, seepage analysis and slope stability analysis were performed by modelling section of field, to confirm the effect of installation of drainage block in GRREW. We can confirm to compare increasing the slope safe factor and decreasing ground water in accordance with drainage blocks.

• Journal of the Korean Geotechnical Society
• /
• 제33권11호
• /
• pp.59-72
• /
• 2017

In this study, the calculation method of the active earth pressure acting on the imaginary vertical plane at the end of the heel of the wall is proposed. For cantilever retaining wall, a change of shear zone behind the wall affects the earth pressure in the vertical plane at the end of heel of the wall depending on wall friction and angle of ground slope. It is very complicated to calculate the earth pressure by a limit equilibrium method (LEM) which considers angles of failure planes varying according to the heel length of the wall. So, the limit analysis method (LAM) is used for calculation of earth pressure in this study. Using the LAM, the earth pressures considering the actual slope angles of failure plane are calculated accurately, and then horizontal and vertical earth pressures are obtained from them respectively. This study results show that by decreasing the relative length of the heel, the slope angle of inward failure plane becomes larger than theoretical slope angle but the slope angle of outward failure plane does not change. And also the friction angle on the vertical plane at the end of the heel of the wall is between the ground slope angle and the wall friction angle, thereafter the active earth pressure decreases. Finally, the Coulomb earth pressure can be easily calculated from the relationship between friction angle (the ratio of vertical earth pressure to horizontal earth pressure) and relative length of the heel (the ratio of heel length to wall height).

• Journal of Korean Society of Forest Science
• /
• 제107권4호
• /
• pp.385-392
• /
• 2018

The slope stabilization analysis was performed by conducting survey and selecting the representative section in order to improve slope composition and management technology of masonry embankments in the quarry area, The mean slope of the masonry retain wall (A, B, C, D, E, F) was $38.5^{\circ}$, although the steep slope of the lowest slope (A) as $59^{\circ}$. The horizontal distance of the masonry embankments is 66.2 m and the slope height is 48.3 m. However, the inclination of the masonry embankments is relatively steep and visually unstable. The slope stability analysis for the slope stability analysis was taken into account during the drying and saturation. The slope stability analysis during saturation was performed by modeling the fully saturated slope. The strength constants of the ground were divided into two groups. The safety factor for dry period was 1.850 and the safety factor for rainy season was 1.333. The safety rate of dry period and rainy season was above 1.5 and 1.2. However, the weathered granite on the upper part of the masonry embankments at the time of heavy rainfall is considered to have a high risk of slope erosion and collapse. Therefore, it is considered necessary to take measures for stabilization through appropriate maintenance such as drainage installation.

• Geotechnical Engineering
• /
• 제12권3호
• /
• pp.35-48
• /
• 1996

Reinforced soil structures may experience large local movements between soil and reinforcement. The failure modes of a reinforced structure depend on several factors which are governed by deformation and slipping of the reinforcement. In some cases, pulling out of the reinforcement may occur instead of rupturing, The growing use of geosynthetic liner system for storage of solid and liquid wastes has led to a number of slope instability problems where the synthetic liner may undergo a large amount of stretching and slipping as a result of the loading. The conventional finite element model for the soil-reinforcement interface uses a zero thickness joint element with normal and shear stiffnesses and can only accommodate a small amount of deformation. When a large slippage occurs, the model provides an i ncorrect mechanism for deformation. This paper presents a new interface finite element model which is able to simulate a large amount of slippage between soil and reinforcement. The formulation of the model is presented and the capability of the model is demonstrated using illustrative examples.

• Journal of the Korean GEO-environmental Society
• /
• 제5권4호
• /
• pp.65-72
• /
• 2004

Within a country, owing to the restriction of aggregate which have been supplied to construction sites, applicability of byproducts such as the copper slag is expected to be more reasonable. In this study, on the basis of characteristics, grain distribution and environmental stability of copper slag, its engineering application was estimated as the vertical and horizontal drainage material. As a results of laboratory tests, it was shown that the permeability of the copper slag was similar to that of sands under vertical drainage condition. In addition, the copper slag showed higher critical hydraulic gradient than that of sand under upward vertical flow state. The copper slag has potential safety against piping and it that the copper slag is suitable for drainage and filter material.

• Tunnel and Underground Space
• /
• 제14권5호
• /
• pp.305-317
• /
• 2004

Due to the steep and narrow characteristic of domestic coal beds, the slant chute caving or sub-level caving method have been mainly adopted in Korea, whereas the long-wall mining has been widely used all around world. However, the slant chute caving or sub-level caving method have disadvantage of not giving much information on the scale and characteristic of abandoned mines. Hence, those information on the abandoned mines in Korea are not easily available. In this study, based on the characteristic investigation of the domestic mining methods, the geological survey and safety analysis were carried out for Donghae highway section 2. Finally, the optimum ground reinforcement methods for that site were selected.

• Geotechnical Engineering
• /
• 제14권2호
• /
• pp.55-66
• /
• 1998

The purpose of this paper is to formulate and apply the stability analysis of toppling failure by considering the variation of discontinuity characteristics, slope geometry, and loading conditions. The stability condition on toppling failure of rock slope is mainly iuluenced by the dip angle $\alpha_B$ and H/t ratio. In order to check toppling failures in design, the stability charts composed of dip angle $\alpha_B$ versus H/t ratio have been constructed in the paper. In general, smaller dip angle $\alpha_B$ and smaller dip angle $\alpha_B$ and smaller H/T ratio give safer condition. The suggested curves change rapidly at the chitical point around the sone, H/t=4~6. The stable zone in stability charles becomes smaller due to step angle $\data$.

• Proceedings of the Korean Geotechical Society Conference
• /
• 한국지반공학회 2005년도 춘계 학술발표회 논문집
• /
• pp.179-184
• /
• 2005

Shear strength parameters obtained from filed survey are important factors in the analysis of slope stability. In this study, sensitivity analysis was performed to evaluate the effect of input parameters on the analysis of slope stability. The input parameters selected for sensitivity analysis were slope angle, cohesion, and friction angle. Monte-Carlo Simulation method was used for calculating input parameters and the factor of safety was computed by means of limit equilibrium method. A rock slope, which has failed in the field, was used for the sensitivity analysis in the analysis of slope stability. The result of analysis shows that the factor of safety of the rock slope was a little low. From partial correlation coefficient(PPC) of input parameters determined from the sensitivity analysis, slope stability was dependant on cohesion and slope angle. The effect of friction angle was lower than that of cohesion and slope angle on slope stability.

• Geotechnical Engineering
• /
• 제11권4호
• /
• pp.87-98
• /
• 1995

Laboratory tests were performed on modeling of in situ remediation of contaminated soils by aqueous solution extraction, thus investigating the feasibility of in situ treatments of soil to promote desorption of organic hazardous wastes. The investigation was conducted using phenol, aniline, quinoline, and 2-napthol adsorbed onto a UH40 soil, and various aqueous solutions were used to desorb, or otherwise remove, these organic contaminants. Decontaminants consisted of deionized water as a reference, hydrogen peroxide, acidy, bases, and surfactants. In situ conditions were modeled in the laboratory by permeating potential extracting liquids through reconstituted, contaminated soil specimens under controlled hydraulic gradients and stress condition through flexible wall permeameter tests. Sodium hydroxide desorbed phenol effectively. Aniline was effectively descorbed by nonionic surfactant. Anionic surfactant remediated quinoline and 2-napthol.

• Journal of the Society of Disaster Information
• /
• 제13권3호
• /
• pp.286-295
• /
• 2017

In this study, it is compared various coefficients of subgrade reaction for application of numerical analysis based on measured data by using various theories and empirical formula. The ratio of the maximum and minimum value is 6.80 at the top of wall but it is 1.06 at the maximum displacement point depends on change of calculated coefficient of subgrade reaction. The data of displacement were generally similar considering an increment of a coefficient of subgrade reaction. And the results of comparison of the displacement at the maximum displacement point by numerical analysis and measured data show similar displacement shape.